From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (qmail 130815 invoked by alias); 6 Jun 2016 12:05:47 -0000 Mailing-List: contact cygwin-help@cygwin.com; run by ezmlm Precedence: bulk List-Id: List-Subscribe: List-Archive: List-Post: List-Help: , Sender: cygwin-owner@cygwin.com Mail-Followup-To: cygwin@cygwin.com Received: (qmail 130805 invoked by uid 89); 6 Jun 2016 12:05:47 -0000 Authentication-Results: sourceware.org; auth=none X-Virus-Found: No X-Spam-SWARE-Status: No, score=0.7 required=5.0 tests=AWL,BAYES_40,FSL_HELO_BARE_IP_2,RCVD_IN_DNSWL_LOW,RCVD_NUMERIC_HELO,RP_MATCHES_RCVD,SPF_HELO_PASS,SPF_PASS autolearn=no version=3.3.2 spammy=Hx-languages-length:725, H*MI:post, H*M:post, waits X-HELO: plane.gmane.org Received: from plane.gmane.org (HELO plane.gmane.org) (80.91.229.3) by sourceware.org (qpsmtpd/0.93/v0.84-503-g423c35a) with (AES256-SHA encrypted) ESMTPS; Mon, 06 Jun 2016 12:05:46 +0000 Received: from list by plane.gmane.org with local (Exim 4.69) (envelope-from ) id 1b9tHq-0002zs-Lq for cygwin@cygwin.com; Mon, 06 Jun 2016 14:05:43 +0200 Received: from 217.10.52.10 ([217.10.52.10]) by main.gmane.org with esmtp (Gmexim 0.1 (Debian)) id 1AlnuQ-0007hv-00 for ; Mon, 06 Jun 2016 14:05:42 +0200 Received: from Stromeko by 217.10.52.10 with local (Gmexim 0.1 (Debian)) id 1AlnuQ-0007hv-00 for ; Mon, 06 Jun 2016 14:05:42 +0200 To: cygwin@cygwin.com From: Achim Gratz Subject: stty icrnl Date: Mon, 06 Jun 2016 12:05:00 -0000 Message-ID: Mime-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit User-Agent: Loom/3.14 (http://gmane.org/) X-IsSubscribed: yes X-SW-Source: 2016-06/txt/msg00058.txt.bz2 I'm trying to connect to a development board via a (USB) serial line. It's using CR rather than NL for line ends, so I was hoping for stty to set that up so I could use screen to communicate with that board. No such joy on Cygwin since the cooked modes are not implemented apparently. Connecting via screen anyway lets me send commands to the board with no problems, but I cannot see any output (presumably because screen waits for the line end ?). I can dump the output into a pipe and see it, but of course not at the same time screen is connected. Is there some other terminal emulator/program that would let me use this board anyway via Cygwin until Cygwin learns cooked mode for terminals? Regards, Achim. -- Problem reports: http://cygwin.com/problems.html FAQ: http://cygwin.com/faq/ Documentation: http://cygwin.com/docs.html Unsubscribe info: http://cygwin.com/ml/#unsubscribe-simple