From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (qmail 11661 invoked by alias); 10 Jul 2002 12:46:48 -0000 Mailing-List: contact ecos-discuss-help@sources.redhat.com; run by ezmlm Precedence: bulk List-Subscribe: List-Archive: List-Post: List-Help: , Sender: ecos-discuss-owner@sources.redhat.com Received: (qmail 11654 invoked from network); 10 Jul 2002 12:46:47 -0000 Received: from unknown (HELO hermes.chez-thomas.org) (63.225.98.241) by sources.redhat.com with SMTP; 10 Jul 2002 12:46:47 -0000 Received: from localhost.localdomain (localhost [127.0.0.1]) by hermes.chez-thomas.org (Postfix) with ESMTP id 9F0281BB; Wed, 10 Jul 2002 06:46:46 -0600 (MDT) From: Gary Thomas To: Christoph Csebits Cc: eCos mailing list In-Reply-To: <20020710144147.A27017@frequentis.com> References: <20020710144147.A27017@frequentis.com> Content-Type: text/plain Content-Transfer-Encoding: 7bit Date: Wed, 10 Jul 2002 05:46:00 -0000 Message-Id: <1026305206.27291.5124.camel@hermes.chez-thomas.org> Mime-Version: 1.0 Subject: Re: [ECOS] init_all_network_interfaces problem with new stack X-SW-Source: 2002-07/txt/msg00125.txt.bz2 On Wed, 2002-07-10 at 06:41, Christoph Csebits wrote: > hi > > i got a problem with the new ip stack at initialization, > here is the output: > > [cyg_net_init] Init: mbinit(0x00000000) > [cyg_net_init] Init: cyg_net_init_devs(0x00000000) > Init device 'fcc_eth0' > Init device 'fcc_eth1' > [cyg_net_init] Init: loopattach(0x00000000) > [cyg_net_init] Init: ifinit(0x00000000) > IFP: 0x00146430, next: 0x00146564 > IFP: 0x00146564, next: 0x001a1568 > IFP: 0x001a1568, next: 0x00000000 > eth0 XXX: driver didn't set ifq_maxlen > eth1 XXX: driver didn't set ifq_maxlen > [cyg_net_init] Init: domaininit(0x00000000) > [cyg_net_init] Init: cyg_net_add_domain(0x001471c8) > New domain internet at 0x00000000 > [cyg_net_init] Init: cyg_net_add_domain(0x00146b90) > New domain route at 0x00000000 > [cyg_net_init] Init: cyg_route_init(0x00000000) > [cyg_net_init] Done > > Start time client - test > Driver can't set multi-cast mode > BOOTP/DHCP failed on eth0 > Driver can't set multi-cast mode > BOOTP/DHCP failed on eth1 > > Are these lines negligible? Should be. > eth0 XXX: driver didn't set ifq_maxlen This is just a warning and a default is supplied in this case. > Driver can't set multi-cast mode This only matters for IPv6 stuff IIRC. > > btw: The "old" ip stack is working well. > its a powerpc based custom board/driver/hal Try a network analyzer (like 'ethereal' on Linux) to see if anything is actually happening on the wire. -- Before posting, please read the FAQ: http://sources.redhat.com/fom/ecos and search the list archive: http://sources.redhat.com/ml/ecos-discuss