* [ECOS] Redboot: "load -m xmodem" command
@ 2002-06-22 1:55 Mike A
2002-06-22 12:25 ` Gary Thomas
2002-06-25 14:50 ` [ECOS] " Iztok Zupet
0 siblings, 2 replies; 3+ messages in thread
From: Mike A @ 2002-06-22 1:55 UTC (permalink / raw)
To: ecos-discuss
Hi,
I Redbooted my ATLAS(MIPS 4Kc) board. Then at the console prompt "Redboot>"
(on Windows Hypertermial) I typed in the command to load the RAM image "load
-m xmodem". Then I select Transfer->Send file (on Hyperterminal). with the
following options I then click OK,
Protocol: Xmodem
file:
C:\myrep\examples\t\t_install\tests\io\wallclock\current\tests\wallclock.srec
The file does not get download...
Even before I start sending from the PC, I see a lot of 'C' being sent from
Redboot in response to "load -m xmodem"
I even tried with ymodem.. I wasn't sucessful
Any clue??
Thanks alot,
-Mike.
_________________________________________________________________
Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp.
--
Before posting, please read the FAQ: http://sources.redhat.com/fom/ecos
and search the list archive: http://sources.redhat.com/ml/ecos-discuss
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [ECOS] Redboot: "load -m xmodem" command
2002-06-22 1:55 [ECOS] Redboot: "load -m xmodem" command Mike A
@ 2002-06-22 12:25 ` Gary Thomas
2002-06-25 14:50 ` [ECOS] " Iztok Zupet
1 sibling, 0 replies; 3+ messages in thread
From: Gary Thomas @ 2002-06-22 12:25 UTC (permalink / raw)
To: Mike A; +Cc: eCos Discussion
On Sat, 2002-06-22 at 01:07, Mike A wrote:
> Hi,
>
> I Redbooted my ATLAS(MIPS 4Kc) board. Then at the console prompt "Redboot>"
> (on Windows Hypertermial) I typed in the command to load the RAM image "load
> -m xmodem". Then I select Transfer->Send file (on Hyperterminal). with the
> following options I then click OK,
>
> Protocol: Xmodem
> file:
> C:\myrep\examples\t\t_install\tests\io\wallclock\current\tests\wallclock.srec
>
> The file does not get download...
>
> Even before I start sending from the PC, I see a lot of 'C' being sent from
> Redboot in response to "load -m xmodem"
>
> I even tried with ymodem.. I wasn't sucessful
>
> Any clue??
The most probable cause is that HAL_DELAY_US() isn't working properly.
The way to check is run the same command (load -m xm) and don't try to
start the transfer. You should see a string of "C" characters, but they
should only come out at a rate of one every 3 or 4 seconds. Any faster
says that the HAL_DELAY_US() macro is broken.
If this is the case, try and fix it and rebuild RedBoot.
As always, if you make changes, it would be nice to pass them back to
the project.
--
Before posting, please read the FAQ: http://sources.redhat.com/fom/ecos
and search the list archive: http://sources.redhat.com/ml/ecos-discuss
^ permalink raw reply [flat|nested] 3+ messages in thread
* [ECOS] Re: Redboot: "load -m xmodem" command
2002-06-22 1:55 [ECOS] Redboot: "load -m xmodem" command Mike A
2002-06-22 12:25 ` Gary Thomas
@ 2002-06-25 14:50 ` Iztok Zupet
1 sibling, 0 replies; 3+ messages in thread
From: Iztok Zupet @ 2002-06-25 14:50 UTC (permalink / raw)
To: Mike A, ecos-discuss
On Saturday 22 June 2002 09:07, Mike A wrote:
> Hi,
>
> I Redbooted my ATLAS(MIPS 4Kc) board. Then at the console prompt "Redboot>"
> (on Windows Hypertermial) I typed in the command to load the RAM image
> "load -m xmodem". Then I select Transfer->Send file (on Hyperterminal).
> with the following options I then click OK,
>
> Protocol: Xmodem
> file:
> C:\myrep\examples\t\t_install\tests\io\wallclock\current\tests\wallclock.sr
>ec
>
> The file does not get download...
>
> Even before I start sending from the PC, I see a lot of 'C' being sent from
> Redboot in response to "load -m xmodem"
>
> I even tried with ymodem.. I wasn't sucessful
>
> Any clue??
>
> Thanks alot,
> -Mike.
>
> _________________________________________________________________
> Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp.
Sorry:
I've been off for a few days. In fact, I never used RedBoot xmodem or zmodem.
I usualy work with GDB or Insight to load, debug and run eCos programs. For
loading only I used only transfer from the tftp server on ethernet.
Maybe somebody else can tell You how it works.
Reagrds
Iz
--
Before posting, please read the FAQ: http://sources.redhat.com/fom/ecos
and search the list archive: http://sources.redhat.com/ml/ecos-discuss
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2002-06-25 21:02 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2002-06-22 1:55 [ECOS] Redboot: "load -m xmodem" command Mike A
2002-06-22 12:25 ` Gary Thomas
2002-06-25 14:50 ` [ECOS] " Iztok Zupet
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).