* RE: [ECOS] Problem downloading eCos
@ 2001-03-20 8:07 Daniel.Andersson
2001-03-20 8:12 ` Jonathan Larmour
2001-03-20 8:17 ` Lewin A.R.W. Edwards
0 siblings, 2 replies; 30+ messages in thread
From: Daniel.Andersson @ 2001-03-20 8:07 UTC (permalink / raw)
To: jlarmour; +Cc: ecos-discuss
I just tried to set RAM using insight and it works fine. I can alter any
memory position that i want so unfortunately i dont think that is the
problem.
Maybe you have a very small file that i can try to download just to see if
its anything wrong with my download file. The current file that i am trying
to download is almost 1Mb and it seems a bit strange since its only a hello
world application. This file was built together with eCos ARM PID default
settings.
/Daniel
> -----Original Message-----
> From: Jonathan Larmour [ mailto:jlarmour@redhat.com ]
> Sent: den 20 mars 2001 16:53
> To: Andersson Daniel
> Cc: ecos-discuss@sourceware.cygnus.com
> Subject: Re: [ECOS] Problem downloading eCos
>
>
> Daniel.Andersson@combitechsystems.com wrote:
> >
> > Hi,
> >
> > I have just recently got my EB40 board on-line with gdb (using
> > serial/angel). However, i cannot download anything to the
> memory. I can view
> > the memory through insight 5.0 but when i connect to target
> and issue a
> > download the whole environment hangs. Has it anything to do
> with my ecos
> > configuration or is it something else?
>
> Have you tried just setting a single memory address in RAM to
> see if that
> works, eg. set *(int *)XXXXXX=0x87654321
>
> where XXXXX is some valid RAM address. Also try using the
> command line to
> eliminate the possibility of it being an insight-specific problem.
>
> Jifl
> --
> Red Hat, Rustat House, Clifton Road, Cambridge, UK. Tel: +44
> (1223) 271062
> Maybe this world is another planet's Hell -Aldous Huxley ||
> Opinions==mine
>
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [ECOS] Problem downloading eCos
2001-03-20 8:07 [ECOS] Problem downloading eCos Daniel.Andersson
@ 2001-03-20 8:12 ` Jonathan Larmour
2001-03-20 8:18 ` Lewin A.R.W. Edwards
2001-03-20 8:17 ` Lewin A.R.W. Edwards
1 sibling, 1 reply; 30+ messages in thread
From: Jonathan Larmour @ 2001-03-20 8:12 UTC (permalink / raw)
To: Daniel.Andersson; +Cc: ecos-discuss
Daniel.Andersson@combitechsystems.com wrote:
>
> I just tried to set RAM using insight and it works fine. I can alter any
> memory position that i want so unfortunately i dont think that is the
> problem.
>
> Maybe you have a very small file that i can try to download just to see if
> its anything wrong with my download file. The current file that i am trying
> to download is almost 1Mb and it seems a bit strange since its only a hello
> world application. This file was built together with eCos ARM PID default
> settings.
Um, ARM PID? But you said your board is an EB40!
Jifl
--
Red Hat, Rustat House, Clifton Road, Cambridge, UK. Tel: +44 (1223) 271062
Maybe this world is another planet's Hell -Aldous Huxley || Opinions==mine
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [ECOS] Problem downloading eCos
2001-03-20 8:12 ` Jonathan Larmour
@ 2001-03-20 8:18 ` Lewin A.R.W. Edwards
2001-03-20 9:41 ` Jonathan Larmour
0 siblings, 1 reply; 30+ messages in thread
From: Lewin A.R.W. Edwards @ 2001-03-20 8:18 UTC (permalink / raw)
To: Jonathan Larmour; +Cc: ecos-discuss
Hi Jonathan,
> > world application. This file was built together with eCos ARM PID default
>
>Um, ARM PID? But you said your board is an EB40!
To the best of your knowledge, did anyone officially pick up the
unsupported AT91EB01 port that was mentioned in the list some time ago?
=== Lewin A.R.W. Edwards (Embedded Engineer)
Work: http://www.digi-frame.com/
Personal: http://www.zws.com/ and http://www.larwe.com/
"Und setzet ihr nicht das Leben ein,
Nie wird euch das Leben gewonnen sein."
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [ECOS] Problem downloading eCos
2001-03-20 8:18 ` Lewin A.R.W. Edwards
@ 2001-03-20 9:41 ` Jonathan Larmour
0 siblings, 0 replies; 30+ messages in thread
From: Jonathan Larmour @ 2001-03-20 9:41 UTC (permalink / raw)
To: Lewin A.R.W. Edwards; +Cc: ecos-discuss
"Lewin A.R.W. Edwards" wrote:
>
> Hi Jonathan,
>
> > > world application. This file was built together with eCos ARM PID default
> >
> >Um, ARM PID? But you said your board is an EB40!
>
> To the best of your knowledge, did anyone officially pick up the
> unsupported AT91EB01 port that was mentioned in the list some time ago?
I've kept the link in my pile of "net things to deal with", but I haven't
actively done anything yet - Carl did say it was quite old so it's not
something I expect to just be able to pick up and use.
Jifl
--
Red Hat, Rustat House, Clifton Road, Cambridge, UK. Tel: +44 (1223) 271062
Maybe this world is another planet's Hell -Aldous Huxley || Opinions==mine
^ permalink raw reply [flat|nested] 30+ messages in thread
* RE: [ECOS] Problem downloading eCos
2001-03-20 8:07 [ECOS] Problem downloading eCos Daniel.Andersson
2001-03-20 8:12 ` Jonathan Larmour
@ 2001-03-20 8:17 ` Lewin A.R.W. Edwards
1 sibling, 0 replies; 30+ messages in thread
From: Lewin A.R.W. Edwards @ 2001-03-20 8:17 UTC (permalink / raw)
To: ecos-discuss
>its anything wrong with my download file. The current file that i am trying
>to download is almost 1Mb and it seems a bit strange since its only a hello
>world application. This file was built together with eCos ARM PID default
When you say it's 1Mb, do you mean that the .exe is 1Mb long, or the actual
code? Use arm-elf-size to check how big the actual code is... the
executable will have loads of debug information in it that isn't uploaded
to the board.
=== Lewin A.R.W. Edwards (Embedded Engineer)
Work: http://www.digi-frame.com/
Personal: http://www.zws.com/ and http://www.larwe.com/
"Und setzet ihr nicht das Leben ein,
Nie wird euch das Leben gewonnen sein."
^ permalink raw reply [flat|nested] 30+ messages in thread
* RE: [ECOS] Problem downloading eCos
@ 2001-03-21 6:04 Daniel.Andersson
2001-03-21 6:13 ` Lewin A.R.W. Edwards
0 siblings, 1 reply; 30+ messages in thread
From: Daniel.Andersson @ 2001-03-21 6:04 UTC (permalink / raw)
To: larwe; +Cc: ecos-discuss
[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #1: Type: text/plain, Size: 1472 bytes --]
Hi,
Since eCos isn´t supported then i don´t have any other options than porting
it because in my project we must use the AT91R40807 processor. And i would
be very greatful if i could use you as a panel in some porting issues.
Is the EB01 eCos port stable at the moment? Can i use it and make the
appropriate changes to suite the EB40 or should i start from some other
source?
By the way, do you have a working "hello world"-example for the EB40 board
(without eCos). Just so a can get my board running.
/Daniel Andersson
> -----Original Message-----
> From: Lewin A.R.W. Edwards [ mailto:larwe@larwe.com ]
> Sent: den 21 mars 2001 14:54
> To: Andersson Daniel; jlarmour@redhat.com
> Cc: ecos-discuss@sourceware.cygnus.com
> Subject: RE: [ECOS] Problem downloading eCos
>
>
> Hi Daniel,
>
> >Yes, the board is an AT91 evaluation board from ATMEL with
> an EB40 mounted
> >on it. The precessor is an AT91R40807. However, i thought
> that the option
> >ARM PID in the eCos configuration tool covered several of
> the ARM boards. Do
>
> The EB40 isn't supported right now. However, if you want to
> work on a port
> for this board, I would be most interested in pooling resources (as a
> personal project, not for my work).
>
> === Lewin A.R.W. Edwards (Embedded Engineer)
> Work: http://www.digi-frame.com/
> Personal: http://www.zws.com/ and http://www.larwe.com/
>
> "Und setzet ihr nicht das Leben ein,
> Nie wird euch das Leben gewonnen sein."
>
^ permalink raw reply [flat|nested] 30+ messages in thread
* RE: [ECOS] Problem downloading eCos
2001-03-21 6:04 Daniel.Andersson
@ 2001-03-21 6:13 ` Lewin A.R.W. Edwards
2001-03-21 8:14 ` Jonathan Larmour
0 siblings, 1 reply; 30+ messages in thread
From: Lewin A.R.W. Edwards @ 2001-03-21 6:13 UTC (permalink / raw)
To: Daniel.Andersson; +Cc: ecos-discuss
[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #1: Type: text/plain, Size: 2272 bytes --]
Hi Daniel,
In response to this (and your other email)...
>Since eCos isn´t supported then i don´t have any other options than porting
>it because in my project we must use the AT91R40807 processor. And i would
>be very greatful if i could use you as a panel in some porting issues.
I'm working with the EB40 for a semi-personal project. Meaning, it is
something I can't get official funding for, so I bought the eval kit and am
working on it at home. Once I get the idea demonstrable, I will bring it to
work and pitch it to management. It's much easier to push an idea to
production if you can say "but all the work is already done..." :)
>Is the EB01 eCos port stable at the moment? Can i use it and make the
>appropriate changes to suite the EB40 or should i start from some other
>source?
I haven't used it. At the moment I am working with standalone code. I have
taken the ARM PID HAL from the current CVS sources and I have started to
work on a from-scratch port, but I don't know when it can be finished.
>By the way, do you have a working "hello world"-example for the EB40 board
>(without eCos). Just so a can get my board running.
OK, I will email you a simple LED blinking app in C (makefile, sourcefiles,
linker script) privately. Please note that this code does _not_ do full C
run-time startup suitable for ROMmed applications. Tauno Voipio (from
comp.arch.embedded) sent me some much more detailed code for standalone
ROMmed applications, but before I can use it I need to write a flashloader
for the EB40 (Atmel doesn't supply a built tool for it).
Tauno is working with somewhat old tools configured rather differently from
the tools used to build eCos. So I have had to do some adapting.
There are also some performance issues with eCos. Due to current gcc
bug(s), it's not possible to compile eCos in Thumb mode. However, Thumb is
_STRONGLY_ recommended on the AT91R40807 because of its 16-bit data path. I
want to solve this issue (read: I want to work out how to un-break eCos
when compiled in thumb mode).
=== Lewin A.R.W. Edwards (Embedded Engineer)
Work: http://www.digi-frame.com/
Personal: http://www.zws.com/ and http://www.larwe.com/
"Und setzet ihr nicht das Leben ein,
Nie wird euch das Leben gewonnen sein."
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [ECOS] Problem downloading eCos
2001-03-21 6:13 ` Lewin A.R.W. Edwards
@ 2001-03-21 8:14 ` Jonathan Larmour
2001-03-21 8:21 ` Lewin A.R.W. Edwards
0 siblings, 1 reply; 30+ messages in thread
From: Jonathan Larmour @ 2001-03-21 8:14 UTC (permalink / raw)
To: Lewin A.R.W. Edwards; +Cc: Daniel.Andersson, ecos-discuss
"Lewin A.R.W. Edwards" wrote:
>
> There are also some performance issues with eCos. Due to current gcc
> bug(s), it's not possible to compile eCos in Thumb mode. However, Thumb is
> _STRONGLY_ recommended on the AT91R40807 because of its 16-bit data path. I
> want to solve this issue (read: I want to work out how to un-break eCos
> when compiled in thumb mode).
Assuming this is the same problem I found (compilation fails with "byte or
halfword not valid for base register"), then work on this:
http://sources.redhat.com/ml/binutils/2001-02/threads.html#00059
If you can produce a small enough testcase for Richard he may be able to
help. This got pushed down my stack and I never got to it (I've been saying
that a lot recently I know).
Jifl
--
Red Hat, Rustat House, Clifton Road, Cambridge, UK. Tel: +44 (1223) 271062
Maybe this world is another planet's Hell -Aldous Huxley || Opinions==mine
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [ECOS] Problem downloading eCos
2001-03-21 8:14 ` Jonathan Larmour
@ 2001-03-21 8:21 ` Lewin A.R.W. Edwards
2001-03-21 8:25 ` Jonathan Larmour
0 siblings, 1 reply; 30+ messages in thread
From: Lewin A.R.W. Edwards @ 2001-03-21 8:21 UTC (permalink / raw)
To: ecos-discuss
Hi Jonathan,
> > There are also some performance issues with eCos. Due to current gcc
> > bug(s), it's not possible to compile eCos in Thumb mode. However, Thumb is
>
>Assuming this is the same problem I found (compilation fails with "byte or
>halfword not valid for base register"), then work on this:
Yep, same problem.
> http://sources.redhat.com/ml/binutils/2001-02/threads.html#00059
That link gets me to a very long list of threads, none of which seems
immediately relevant, but I just took a cursory look over the page.
>If you can produce a small enough testcase for Richard he may be able to
I'll _try_. At the moment I am still recovering from a reformat, so I'm
still re-downloading CVS trees of half the software in the universe. "The
statistical probability is that other civilizations will arise. There will
some day be lemon-scented paper napkins. Until then, there will be a short
delay. Please return to your seat".
>help. This got pushed down my stack and I never got to it (I've been saying
>that a lot recently I know).
It's OK, the bottom of my stack will never see the light of day. Could be a
couple of prehistoric Cro-Magnon plates down there for all I know.
=== Lewin A.R.W. Edwards (Embedded Engineer)
Work: http://www.digi-frame.com/
Personal: http://www.zws.com/ and http://www.larwe.com/
"Und setzet ihr nicht das Leben ein,
Nie wird euch das Leben gewonnen sein."
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [ECOS] Problem downloading eCos
2001-03-21 8:21 ` Lewin A.R.W. Edwards
@ 2001-03-21 8:25 ` Jonathan Larmour
2001-03-21 8:36 ` Lewin A.R.W. Edwards
0 siblings, 1 reply; 30+ messages in thread
From: Jonathan Larmour @ 2001-03-21 8:25 UTC (permalink / raw)
To: Lewin A.R.W. Edwards; +Cc: ecos-discuss
"Lewin A.R.W. Edwards" wrote:
>
> Hi Jonathan,
>
> > > There are also some performance issues with eCos. Due to current gcc
> > > bug(s), it's not possible to compile eCos in Thumb mode. However, Thumb is
> >
> >Assuming this is the same problem I found (compilation fails with "byte or
> >halfword not valid for base register"), then work on this:
>
> Yep, same problem.
>
> > http://sources.redhat.com/ml/binutils/2001-02/threads.html#00059
>
> That link gets me to a very long list of threads, none of which seems
> immediately relevant, but I just took a cursory look over the page.
It should be centred on one thread titled "ARM thumb byte stores"
Thanks for volunteering to give it a go!
Jifl
--
Red Hat, Rustat House, Clifton Road, Cambridge, UK. Tel: +44 (1223) 271062
Maybe this world is another planet's Hell -Aldous Huxley || Opinions==mine
^ permalink raw reply [flat|nested] 30+ messages in thread
* RE: [ECOS] Problem downloading eCos
@ 2001-03-20 23:45 Daniel.Andersson
2001-03-20 23:52 ` Jonathan Larmour
2001-03-21 5:54 ` Lewin A.R.W. Edwards
0 siblings, 2 replies; 30+ messages in thread
From: Daniel.Andersson @ 2001-03-20 23:45 UTC (permalink / raw)
To: jlarmour; +Cc: ecos-discuss
Hi again,
Yes, the board is an AT91 evaluation board from ATMEL with an EB40 mounted
on it. The precessor is an AT91R40807. However, i thought that the option
ARM PID in the eCos configuration tool covered several of the ARM boards. Do
you mean that there are no port of eCos for my platform? And if eCos can run
on my platform how do i set up eCos to suite this board (if not to use the
PID option)?
/Daniel
> -----Original Message-----
> From: Jonathan Larmour [ mailto:jlarmour@redhat.com ]
> Sent: den 20 mars 2001 17:12
> To: Andersson Daniel
> Cc: ecos-discuss@sourceware.cygnus.com
> Subject: Re: [ECOS] Problem downloading eCos
>
>
> Daniel.Andersson@combitechsystems.com wrote:
> >
> > I just tried to set RAM using insight and it works fine. I
> can alter any
> > memory position that i want so unfortunately i dont think
> that is the
> > problem.
> >
> > Maybe you have a very small file that i can try to download
> just to see if
> > its anything wrong with my download file. The current file
> that i am trying
> > to download is almost 1Mb and it seems a bit strange since
> its only a hello
> > world application. This file was built together with eCos
> ARM PID default
> > settings.
>
> Um, ARM PID? But you said your board is an EB40!
>
> Jifl
> --
> Red Hat, Rustat House, Clifton Road, Cambridge, UK. Tel: +44
> (1223) 271062
> Maybe this world is another planet's Hell -Aldous Huxley ||
> Opinions==mine
>
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [ECOS] Problem downloading eCos
2001-03-20 23:45 Daniel.Andersson
@ 2001-03-20 23:52 ` Jonathan Larmour
2001-03-21 0:47 ` massey steven
2001-03-21 5:54 ` Lewin A.R.W. Edwards
1 sibling, 1 reply; 30+ messages in thread
From: Jonathan Larmour @ 2001-03-20 23:52 UTC (permalink / raw)
To: Daniel.Andersson; +Cc: ecos-discuss
Daniel.Andersson@combitechsystems.com wrote:
>
> Hi again,
>
> Yes, the board is an AT91 evaluation board from ATMEL with an EB40 mounted
> on it. The precessor is an AT91R40807. However, i thought that the option
> ARM PID in the eCos configuration tool covered several of the ARM boards.
Alas no.
> Do
> you mean that there are no port of eCos for my platform? And if eCos can run
> on my platform how do i set up eCos to suite this board (if not to use the
> PID option)?
There is no port included in the standard eCos sources yet. I think you may
want to start here:
http://sources.redhat.com/ml/ecos-discuss/2001-01/msg00496.html
Jifl
--
Red Hat, Rustat House, Clifton Road, Cambridge, UK. Tel: +44 (1223) 271062
Maybe this world is another planet's Hell -Aldous Huxley || Opinions==mine
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [ECOS] Problem downloading eCos
2001-03-20 23:52 ` Jonathan Larmour
@ 2001-03-21 0:47 ` massey steven
0 siblings, 0 replies; 30+ messages in thread
From: massey steven @ 2001-03-21 0:47 UTC (permalink / raw)
To: Daniel.Andersson; +Cc: ecos-discuss
--- Jonathan Larmour <jlarmour@redhat.com> wrote:
> Daniel.Andersson@combitechsystems.com wrote:
> >
> > Hi again,
> >
> > Yes, the board is an AT91 evaluation board from ATMEL with an EB40 mounted
> > on it. The precessor is an AT91R40807. However, i thought that the option
> > ARM PID in the eCos configuration tool covered several of the ARM boards.
>
> Alas no.
>
> > Do
> > you mean that there are no port of eCos for my platform? And if eCos can run
> > on my platform how do i set up eCos to suite this board (if not to use the
> > PID option)?
>
> There is no port included in the standard eCos sources yet. I think you may
> want to start here:
> http://sources.redhat.com/ml/ecos-discuss/2001-01/msg00496.html
>
> Jifl
> --
> Red Hat, Rustat House, Clifton Road, Cambridge, UK. Tel: +44 (1223) 271062
> Maybe this world is another planet's Hell -Aldous Huxley || Opinions==mine
Hello All,
It's been a long while since i've worked with eCos. But, i had it working fine on the
EB01/AT9140807 board, using Carl's & my updates. Really it's pretty trivial. But, I am
just now starting back on my project and can probably provide assistance. Maybe, we can
finally get the EB01/EB40 platforms permanantly in the source tree??
Have Fun,
Steven Massey
__________________________________________________
Do You Yahoo!?
Get email at your own domain with Yahoo! Mail.
http://personal.mail.yahoo.com/
^ permalink raw reply [flat|nested] 30+ messages in thread
* RE: [ECOS] Problem downloading eCos
2001-03-20 23:45 Daniel.Andersson
2001-03-20 23:52 ` Jonathan Larmour
@ 2001-03-21 5:54 ` Lewin A.R.W. Edwards
1 sibling, 0 replies; 30+ messages in thread
From: Lewin A.R.W. Edwards @ 2001-03-21 5:54 UTC (permalink / raw)
To: Daniel.Andersson, jlarmour; +Cc: ecos-discuss
Hi Daniel,
>Yes, the board is an AT91 evaluation board from ATMEL with an EB40 mounted
>on it. The precessor is an AT91R40807. However, i thought that the option
>ARM PID in the eCos configuration tool covered several of the ARM boards. Do
The EB40 isn't supported right now. However, if you want to work on a port
for this board, I would be most interested in pooling resources (as a
personal project, not for my work).
=== Lewin A.R.W. Edwards (Embedded Engineer)
Work: http://www.digi-frame.com/
Personal: http://www.zws.com/ and http://www.larwe.com/
"Und setzet ihr nicht das Leben ein,
Nie wird euch das Leben gewonnen sein."
^ permalink raw reply [flat|nested] 30+ messages in thread
* [ECOS] Problem downloading eCos
@ 2001-03-20 7:43 Daniel.Andersson
2001-03-20 7:53 ` Jonathan Larmour
2001-03-20 8:15 ` Jesper Skov
0 siblings, 2 replies; 30+ messages in thread
From: Daniel.Andersson @ 2001-03-20 7:43 UTC (permalink / raw)
To: ecos-discuss
Hi,
I have just recently got my EB40 board on-line with gdb (using
serial/angel). However, i cannot download anything to the memory. I can view
the memory through insight 5.0 but when i connect to target and issue a
download the whole environment hangs. Has it anything to do with my ecos
configuration or is it something else?
Regards, Daniel
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [ECOS] Problem downloading eCos
2001-03-20 7:43 Daniel.Andersson
@ 2001-03-20 7:53 ` Jonathan Larmour
2001-03-20 8:15 ` Jesper Skov
1 sibling, 0 replies; 30+ messages in thread
From: Jonathan Larmour @ 2001-03-20 7:53 UTC (permalink / raw)
To: Daniel.Andersson; +Cc: ecos-discuss
Daniel.Andersson@combitechsystems.com wrote:
>
> Hi,
>
> I have just recently got my EB40 board on-line with gdb (using
> serial/angel). However, i cannot download anything to the memory. I can view
> the memory through insight 5.0 but when i connect to target and issue a
> download the whole environment hangs. Has it anything to do with my ecos
> configuration or is it something else?
Have you tried just setting a single memory address in RAM to see if that
works, eg. set *(int *)XXXXXX=0x87654321
where XXXXX is some valid RAM address. Also try using the command line to
eliminate the possibility of it being an insight-specific problem.
Jifl
--
Red Hat, Rustat House, Clifton Road, Cambridge, UK. Tel: +44 (1223) 271062
Maybe this world is another planet's Hell -Aldous Huxley || Opinions==mine
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [ECOS] Problem downloading eCos
2001-03-20 7:43 Daniel.Andersson
2001-03-20 7:53 ` Jonathan Larmour
@ 2001-03-20 8:15 ` Jesper Skov
1 sibling, 0 replies; 30+ messages in thread
From: Jesper Skov @ 2001-03-20 8:15 UTC (permalink / raw)
To: Daniel.Andersson; +Cc: ecos-discuss
>>>>> "Daniel" == Daniel Andersson <Daniel.Andersson@combitechsystems.com> writes:
Daniel> Hi, I have just recently got my EB40 board on-line with gdb
What is a EB40 board?
Daniel> (using serial/angel). However, i cannot download anything to
Daniel> the memory. I can view the memory through insight 5.0 but when
Daniel> i connect to target and issue a download the whole environment
Daniel> hangs. Has it anything to do with my ecos configuration or is
Daniel> it something else?
Uh, more likely that there's no eCos port for the platform. What
target did you compile for?
Jesper
^ permalink raw reply [flat|nested] 30+ messages in thread
end of thread, other threads:[~2001-03-22 11:39 UTC | newest]
Thread overview: 30+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2001-03-20 8:07 [ECOS] Problem downloading eCos Daniel.Andersson
2001-03-20 8:12 ` Jonathan Larmour
2001-03-20 8:18 ` Lewin A.R.W. Edwards
2001-03-20 9:41 ` Jonathan Larmour
2001-03-20 8:17 ` Lewin A.R.W. Edwards
-- strict thread matches above, loose matches on Subject: below --
2001-03-21 6:04 Daniel.Andersson
2001-03-21 6:13 ` Lewin A.R.W. Edwards
2001-03-21 8:14 ` Jonathan Larmour
2001-03-21 8:21 ` Lewin A.R.W. Edwards
2001-03-21 8:25 ` Jonathan Larmour
2001-03-21 8:36 ` Lewin A.R.W. Edwards
[not found] ` <3AB8D972.43A4B1B1@redhat.com>
2001-03-21 9:44 ` Lewin A.R.W. Edwards
2001-03-21 10:09 ` Jonathan Larmour
2001-03-21 10:15 ` Lewin A.R.W. Edwards
2001-03-21 11:45 ` Lewin A.R.W. Edwards
2001-03-21 12:42 ` Jonathan Larmour
2001-03-21 13:13 ` Lewin A.R.W. Edwards
2001-03-21 11:49 ` Lewin A.R.W. Edwards
2001-03-21 13:29 ` Jonathan Larmour
2001-03-21 13:48 ` Lewin A.R.W. Edwards
2001-03-22 8:27 ` Lewin A.R.W. Edwards
2001-03-22 11:37 ` Jonathan Larmour
2001-03-22 11:39 ` Lewin A.R.W. Edwards
2001-03-20 23:45 Daniel.Andersson
2001-03-20 23:52 ` Jonathan Larmour
2001-03-21 0:47 ` massey steven
2001-03-21 5:54 ` Lewin A.R.W. Edwards
2001-03-20 7:43 Daniel.Andersson
2001-03-20 7:53 ` Jonathan Larmour
2001-03-20 8:15 ` Jesper Skov
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).