* [SH][committed] Remove SH5 support in compiler
@ 2016-04-28 1:27 Oleg Endo
2016-04-29 10:45 ` Oleg Endo
0 siblings, 1 reply; 10+ messages in thread
From: Oleg Endo @ 2016-04-28 1:27 UTC (permalink / raw)
To: gcc-patches
[-- Attachment #1: Type: text/plain, Size: 1334 bytes --]
Hi,
The removal of SH5 support from GCC has been announced here
https://gcc.gnu.org/ml/gcc/2015-08/msg00101.html
The attached patch removes support for SH5 in the compiler back end.
There are still some leftovers and new simplification opportunities.
These will be addressed in later follow up patches.
Tested on sh-elf with
make -k check RUNTESTFLAGS="--target_board=sh-sim\{-m2/-ml,-m2/-mb,
-m2a/-mb,-m4/-ml,-m4/-mb,-m4a/-ml,-m4a/-mb}"
Committed as r235544.
Cheers,
Oleg
gcc/ChangeLog:
* common/config/sh/sh-common.c: Remove SH5 support.
* config/sh/constraints.md: Likewise.
* config/sh/config/sh/elf.h: Likewise.
* config/sh/linux.h: Likewise.
* config/sh/netbsd-elf.h: Likewise.
* config/sh/predicates.md: Likewise.
* config/sh/sh-c.c: Likewise.
* config/sh/sh-protos.h: Likewise.
* config/sh/sh.c: Likewise.
* config/sh/sh.h: Likewise.
* config/sh/sh.md: Likewise.
* config/sh/sh.opt: Likewise.
* config/sh/sync.md: Likewise.
* config/sh/sh64.h: Delete.
* config/sh/shmedia.h: Likewise.
* config/sh/shmedia.md: Likewise.
* config/sh/sshmedia.h: Likewise.
* config/sh/t-netbsd-sh5-64: Likewise.
* config/sh/t-sh64: Likewise.
* config/sh/ushmedia.h: Likewise.
[-- Attachment #2: remove_sh64_sh5_gcc_2.patch.tar.gz --]
[-- Type: application/x-compressed-tar, Size: 91975 bytes --]
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [SH][committed] Remove SH5 support in compiler
2016-04-28 1:27 [SH][committed] Remove SH5 support in compiler Oleg Endo
@ 2016-04-29 10:45 ` Oleg Endo
2016-04-29 14:11 ` Oleg Endo
0 siblings, 1 reply; 10+ messages in thread
From: Oleg Endo @ 2016-04-29 10:45 UTC (permalink / raw)
To: gcc-patches
[-- Attachment #1: Type: text/plain, Size: 1441 bytes --]
On Thu, 2016-04-28 at 10:27 +0900, Oleg Endo wrote:
> The removal of SH5 support from GCC has been announced here
> https://gcc.gnu.org/ml/gcc/2015-08/msg00101.html
>
> The attached patch removes support for SH5 in the compiler back end.
> There are still some leftovers and new simplification opportunities.
> These will be addressed in later follow up patches.
>
> Tested on sh-elf with
>
> make -k check RUNTESTFLAGS="--target_board=sh-sim\{-m2/-ml,-m2/-mb,
> -m2a/-mb,-m4/-ml,-m4/-mb,-m4a/-ml,-m4a/-mb}"
The attached patch removes some leftovers and reinstantes the divsf3
expander pattern which got accidentally deleted by the previous patch.
Tested as above, commited as r235632.
Cheers,
Oleg
inlcude/ChangeLog:
* longlong.h (umul_ppmm): Remove SHMEDIA checks.
(__umulsidi3, count_leading_zeros): Remove SHMEDIA implementations.
gcc/ChangeLog:
* common/config/sh/sh-common.c (sh_option_optimization_table): Remove
remaining SH5 related settings.
* config/sh/sh-protos.h (shmedia_cleanup_truncate,
shmedia_prepare_call_address): Delete.
* config/sh/sh.c (sh_print_operand, output_stack_adjust,
DWARF_CIE_DATA_ALIGNMENT, LOCAL_ALIGNMENT): Update comments.
* config/sh/sh.h (SUBTARGET_ASM_RELAX_SPEC,
UNSUPPORTED_SH2A): Remove m5 checks.
(sh_divide_strategy_e): Remove SH5 division strategies.
(TARGET_PTRMEMFUNC_VBIT_LOCATION): Remove and use default.
* config/sh/sh.md (divsf3): Reinstate define_expand pattern.
[-- Attachment #2: remove_sh64_sh5_gcc_3.patch --]
[-- Type: text/x-patch, Size: 8734 bytes --]
diff --git a/gcc/common/config/sh/sh-common.c b/gcc/common/config/sh/sh-common.c
index ee6e4c9..d7c91b8 100644
--- a/gcc/common/config/sh/sh-common.c
+++ b/gcc/common/config/sh/sh-common.c
@@ -31,15 +31,8 @@ along with GCC; see the file COPYING3. If not see
static const struct default_options sh_option_optimization_table[] =
{
{ OPT_LEVELS_1_PLUS, OPT_fomit_frame_pointer, NULL, 1 },
- { OPT_LEVELS_1_PLUS_SPEED_ONLY, OPT_mdiv_, "inv:minlat", 1 },
{ OPT_LEVELS_SIZE, OPT_mdiv_, SH_DIV_STR_FOR_SIZE, 1 },
{ OPT_LEVELS_0_ONLY, OPT_mdiv_, "", 1 },
- /* We can't meaningfully test TARGET_SHMEDIA here, because -m
- options haven't been parsed yet, hence we'd read only the
- default. sh_target_reg_class will return NO_REGS if this is
- not SHMEDIA, so it's OK to always set
- flag_branch_target_load_optimize. */
- { OPT_LEVELS_2_PLUS, OPT_fbranch_target_load_optimize, NULL, 1 },
{ OPT_LEVELS_NONE, 0, NULL, 0 }
};
diff --git a/gcc/config/sh/sh-protos.h b/gcc/config/sh/sh-protos.h
index 537ab39..ea7e847 100644
--- a/gcc/config/sh/sh-protos.h
+++ b/gcc/config/sh/sh-protos.h
@@ -392,11 +392,8 @@ extern void sh_init_cumulative_args (CUMULATIVE_ARGS *, tree, rtx, tree,
signed int, machine_mode);
extern rtx sh_dwarf_register_span (rtx);
-extern int shmedia_cleanup_truncate (rtx);
-
extern bool sh_contains_memref_p (rtx);
extern bool sh_loads_bankedreg_p (rtx);
-extern rtx shmedia_prepare_call_address (rtx fnaddr, int is_sibcall);
extern int sh2a_get_function_vector_number (rtx);
extern bool sh2a_is_function_vector_call (rtx);
extern void sh_fix_range (const char *);
diff --git a/gcc/config/sh/sh.c b/gcc/config/sh/sh.c
index e6680af..3d9ce9d 100644
--- a/gcc/config/sh/sh.c
+++ b/gcc/config/sh/sh.c
@@ -1177,9 +1177,6 @@ sh_print_operand (FILE *stream, rtx x, int code)
output_addr_const (stream, x);
break;
/* N.B.: %R / %S / %T adjust memory addresses by four.
- For SHMEDIA, that means they can be used to access the first and
- second 32 bit part of a 64 bit (or larger) value that
- might be held in floating point registers or memory.
While they can be used to access 64 bit parts of a larger value
held in general purpose registers, that won't work with memory -
neither for fp registers, since the frxx names are used. */
@@ -6748,15 +6745,12 @@ output_stack_adjust (int size, rtx reg, int epilogue_p,
rtx adj_reg, tmp_reg, mem;
/* If we reached here, the most likely case is the (sibcall)
- epilogue for non SHmedia. Put a special push/pop sequence
- for such case as the last resort. This looks lengthy but
- would not be problem because it seems to be very
- rare. */
-
+ epilogue. Put a special push/pop sequence for such case as
+ the last resort. This looks lengthy but would not be problem
+ because it seems to be very rare. */
gcc_assert (epilogue_p);
-
- /* ??? There is still the slight possibility that r4 or
+ /* ??? There is still the slight possibility that r4 or
r5 have been reserved as fixed registers or assigned
as global registers, and they change during an
interrupt. There are possible ways to handle this:
diff --git a/gcc/config/sh/sh.h b/gcc/config/sh/sh.h
index 0303527..9f104f0 100644
--- a/gcc/config/sh/sh.h
+++ b/gcc/config/sh/sh.h
@@ -206,7 +206,7 @@ extern int code_for_indirect_jump_scratch;
SUBTARGET_EXTRA_SPECS
#if TARGET_CPU_DEFAULT & MASK_HARD_SH4
-#define SUBTARGET_ASM_RELAX_SPEC "%{!m1:%{!m2:%{!m3*:%{!m5*:-isa=sh4-up}}}}"
+#define SUBTARGET_ASM_RELAX_SPEC "%{!m1:%{!m2:%{!m3*::-isa=sh4-up}}}"
#else
#define SUBTARGET_ASM_RELAX_SPEC "%{m4*:-isa=sh4-up}"
#endif
@@ -250,7 +250,7 @@ extern int code_for_indirect_jump_scratch;
/* Strict nofpu means that the compiler should tell the assembler
to reject FPU instructions. E.g. from ASM inserts. */
#if TARGET_CPU_DEFAULT & MASK_HARD_SH4 && !(TARGET_CPU_DEFAULT & MASK_SH_E)
-#define SUBTARGET_ASM_ISA_SPEC "%{!m1:%{!m2:%{!m3*:%{m4-nofpu|!m4*:%{!m5:-isa=sh4-nofpu}}}}}"
+#define SUBTARGET_ASM_ISA_SPEC "%{!m1:%{!m2:%{!m3*:%{m4-nofpu|!m4*::-isa=sh4-nofpu}}}}"
#else
#define SUBTARGET_ASM_ISA_SPEC \
@@ -299,7 +299,7 @@ extern int code_for_indirect_jump_scratch;
#if TARGET_CPU_DEFAULT & MASK_HARD_SH2A
#define UNSUPPORTED_SH2A IS_LITTLE_ENDIAN_OPTION \
-"%{m2a*|!m1:%{!m2*:%{!m3*:%{!m4*:{!m5*:%eSH2a does not support little-endian}}}}}}"
+"%{m2a*|!m1:%{!m2*:%{!m3*:%{!m4*:%eSH2a does not support little-endian}}}}}"
#else
#define UNSUPPORTED_SH2A IS_LITTLE_ENDIAN_OPTION \
"%{m2a*:%eSH2a does not support little-endian}}"
@@ -323,17 +323,6 @@ extern int code_for_indirect_jump_scratch;
extern int assembler_dialect;
enum sh_divide_strategy_e {
- /* SH5 strategies. */
- SH_DIV_CALL,
- SH_DIV_CALL2,
- SH_DIV_FP, /* We could do this also for SH4. */
- SH_DIV_INV,
- SH_DIV_INV_MINLAT,
- SH_DIV_INV20U,
- SH_DIV_INV20L,
- SH_DIV_INV_CALL,
- SH_DIV_INV_CALL2,
- SH_DIV_INV_FP,
/* SH1 .. SH4 strategies. Because of the small number of registers
available, the compiler uses knowledge of the actual set of registers
being clobbered by the different functions called. */
@@ -390,10 +379,7 @@ extern enum sh_divide_strategy_e sh_div_strategy;
#define MIN_UNITS_PER_WORD 4
/* Scaling factor for Dwarf data offsets for CFI information.
- The dwarf2out.c default would use -UNITS_PER_WORD, which is -8 for
- SHmedia; however, since we do partial register saves for the registers
- visible to SHcompact, and for target registers for SHMEDIA32, we have
- to allow saves that are only 4-byte aligned. */
+ The dwarf2out.c default would use -UNITS_PER_WORD. */
#define DWARF_CIE_DATA_ALIGNMENT -4
/* Width in bits of a pointer.
@@ -415,11 +401,6 @@ extern enum sh_divide_strategy_e sh_div_strategy;
code of a function. */
#define FUNCTION_BOUNDARY (16)
-/* On SH5, the lowest bit is used to indicate SHmedia functions, so
- the vbit must go into the delta field of
- pointers-to-member-functions. */
-#define TARGET_PTRMEMFUNC_VBIT_LOCATION (ptrmemfunc_vbit_in_pfn)
-
/* Alignment of field after `int : 0' in a structure. */
#define EMPTY_FIELD_BOUNDARY 32
@@ -437,9 +418,7 @@ extern enum sh_divide_strategy_e sh_div_strategy;
/* get_mode_alignment assumes complex values are always held in multiple
registers, but that is not the case on the SH; CQImode and CHImode are
- held in a single integer register. SH5 also holds CSImode and SCmode
- values in integer registers. This is relevant for argument passing on
- SHcompact as we use a stack temp in order to pass CSImode by reference. */
+ held in a single integer register. */
#define LOCAL_ALIGNMENT(TYPE, ALIGN) \
((GET_MODE_CLASS (TYPE_MODE (TYPE)) == MODE_COMPLEX_INT \
|| GET_MODE_CLASS (TYPE_MODE (TYPE)) == MODE_COMPLEX_FLOAT) \
diff --git a/gcc/config/sh/sh.md b/gcc/config/sh/sh.md
index 0e70ea2..ef90303 100644
--- a/gcc/config/sh/sh.md
+++ b/gcc/config/sh/sh.md
@@ -9300,6 +9300,16 @@
[(set_attr "type" "fp")
(set_attr "fp_mode" "single")])
+(define_expand "divsf3"
+ [(set (match_operand:SF 0 "fp_arith_reg_operand")
+ (div:SF (match_operand:SF 1 "fp_arith_reg_operand")
+ (match_operand:SF 2 "fp_arith_reg_operand")))]
+ "TARGET_SH2E"
+{
+ emit_insn (gen_divsf3_i (operands[0], operands[1], operands[2]));
+ DONE;
+})
+
(define_insn "divsf3_i"
[(set (match_operand:SF 0 "fp_arith_reg_operand" "=f")
(div:SF (match_operand:SF 1 "fp_arith_reg_operand" "0")
diff --git a/include/longlong.h b/include/longlong.h
index 34ad9b4..5529974 100644
--- a/include/longlong.h
+++ b/include/longlong.h
@@ -1086,7 +1086,7 @@ extern UDItype __umulsidi3 (USItype, USItype);
} while (0)
#endif
-#if defined(__sh__) && (!defined (__SHMEDIA__) || !__SHMEDIA__) && W_TYPE_SIZE == 32
+#if defined(__sh__) && W_TYPE_SIZE == 32
#ifndef __sh1__
#define umul_ppmm(w1, w0, u, v) \
__asm__ ( \
@@ -1159,21 +1159,6 @@ extern UDItype __umulsidi3 (USItype, USItype);
#endif /* __sh__ */
-#if defined (__SH5__) && defined (__SHMEDIA__) && __SHMEDIA__ && W_TYPE_SIZE == 32
-#define __umulsidi3(u,v) ((UDItype)(USItype)u*(USItype)v)
-#define count_leading_zeros(count, x) \
- do \
- { \
- UDItype x_ = (USItype)(x); \
- SItype c_; \
- \
- __asm__ ("nsb %1, %0" : "=r" (c_) : "r" (x_)); \
- (count) = c_ - 31; \
- } \
- while (0)
-#define COUNT_LEADING_ZEROS_0 32
-#endif
-
#if defined (__sparc__) && !defined (__arch64__) && !defined (__sparcv9) \
&& W_TYPE_SIZE == 32
#define add_ssaaaa(sh, sl, ah, al, bh, bl) \
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [SH][committed] Remove SH5 support in compiler
2016-04-29 10:45 ` Oleg Endo
@ 2016-04-29 14:11 ` Oleg Endo
2016-04-30 1:58 ` Oleg Endo
0 siblings, 1 reply; 10+ messages in thread
From: Oleg Endo @ 2016-04-29 14:11 UTC (permalink / raw)
To: gcc-patches
[-- Attachment #1: Type: text/plain, Size: 1170 bytes --]
On Fri, 2016-04-29 at 19:45 +0900, Oleg Endo wrote:
> On Thu, 2016-04-28 at 10:27 +0900, Oleg Endo wrote:
>
> > The removal of SH5 support from GCC has been announced here
> > https://gcc.gnu.org/ml/gcc/2015-08/msg00101.html
> >
> > The attached patch removes support for SH5 in the compiler back
> > end.
> > There are still some leftovers and new simplification
> > opportunities.
> > These will be addressed in later follow up patches.
> >
> > Tested on sh-elf with
> >
> > make -k check RUNTESTFLAGS="--target_board=sh-sim\{-m2/-ml,-m2/-mb,
> > -m2a/-mb,-m4/-ml,-m4/-mb,-m4a/-ml,-m4a/-mb}"
>
> The attached patch removes some leftovers and reinstantes the divsf3
> expander pattern which got accidentally deleted by the previous
> patch.
The attached patch removes SH5 support from libgcc.
Tested as above. Committed as r235640.
Cheers,
Oleg
libgcc/ChangeLog:
* config/sh/crt1.S: Remove SH5 support.
* config/sh/crti.S: Likewise.
* config/sh/crtn.S: Likewise.
* config/sh/lib1funcs-4-300.S: Likewise.
* config/sh/lib1funcs-Os-4-200.S: Likewise.
* config/sh/lib1funcs.S: Likewise.
* config/sh/linux-unwind.h: Likewise.
* config/sh/t-sh64: Delete.
[-- Attachment #2: remove_sh64_sh5_libgcc_4.patch --]
[-- Type: text/x-patch, Size: 77850 bytes --]
diff --git a/libgcc/config/sh/crt1.S b/libgcc/config/sh/crt1.S
index 45e4aad..4e3c27d 100644
--- a/libgcc/config/sh/crt1.S
+++ b/libgcc/config/sh/crt1.S
@@ -38,648 +38,6 @@ __timer_stack:
/* ;----------------------------------------
Normal newlib crt1.S */
-#ifdef __SH5__
- .section .data,"aw"
- .global ___data
-___data:
-
- .section .rodata,"a"
- .global ___rodata
-___rodata:
-
-#define ICCR_BASE 0x01600000
-#define OCCR_BASE 0x01e00000
-#define MMUIR_BASE 0x00000000
-#define MMUDR_BASE 0x00800000
-
-#define PTE_ENABLED 1
-#define PTE_DISABLED 0
-
-#define PTE_SHARED (1 << 1)
-#define PTE_NOT_SHARED 0
-
-#define PTE_CB_UNCACHEABLE 0
-#define PTE_CB_DEVICE 1
-#define PTE_CB_CACHEABLE_WB 2
-#define PTE_CB_CACHEABLE_WT 3
-
-#define PTE_SZ_4KB (0 << 3)
-#define PTE_SZ_64KB (1 << 3)
-#define PTE_SZ_1MB (2 << 3)
-#define PTE_SZ_512MB (3 << 3)
-
-#define PTE_PRR (1 << 6)
-#define PTE_PRX (1 << 7)
-#define PTE_PRW (1 << 8)
-#define PTE_PRU (1 << 9)
-
-#define SR_MMU_BIT 31
-#define SR_BL_BIT 28
-
-#define ALIGN_4KB (0xfff)
-#define ALIGN_1MB (0xfffff)
-#define ALIGN_512MB (0x1fffffff)
-
-#define DYNACON_BASE 0x0f000000
-#define DM_CB_DLINK_BASE 0x0c000000
-#define DM_DB_DLINK_BASE 0x0b000000
-
-#define FEMI_AREA_0 0x00000000
-#define FEMI_AREA_1 0x04000000
-#define FEMI_AREA_2 0x05000000
-#define FEMI_AREA_3 0x06000000
-#define FEMI_AREA_4 0x07000000
-#define FEMI_CB 0x08000000
-
-#define EMI_BASE 0X80000000
-
-#define DMA_BASE 0X0e000000
-
-#define CPU_BASE 0X0d000000
-
-#define PERIPH_BASE 0X09000000
-#define DMAC_BASE 0x0e000000
-#define INTC_BASE 0x0a000000
-#define CPRC_BASE 0x0a010000
-#define TMU_BASE 0x0a020000
-#define SCIF_BASE 0x0a030000
-#define RTC_BASE 0x0a040000
-
-
-
-#define LOAD_CONST32(val, reg) \
- movi ((val) >> 16) & 65535, reg; \
- shori (val) & 65535, reg
-
-#define LOAD_PTEH_VAL(sym, align, bits, scratch_reg, reg) \
- LOAD_ADDR (sym, reg); \
- LOAD_CONST32 ((align), scratch_reg); \
- andc reg, scratch_reg, reg; \
- LOAD_CONST32 ((bits), scratch_reg); \
- or reg, scratch_reg, reg
-
-#define LOAD_PTEL_VAL(sym, align, bits, scratch_reg, reg) \
- LOAD_ADDR (sym, reg); \
- LOAD_CONST32 ((align), scratch_reg); \
- andc reg, scratch_reg, reg; \
- LOAD_CONST32 ((bits), scratch_reg); \
- or reg, scratch_reg, reg
-
-#define SET_PTE(pte_addr_reg, pteh_val_reg, ptel_val_reg) \
- putcfg pte_addr_reg, 0, r63; \
- putcfg pte_addr_reg, 1, ptel_val_reg; \
- putcfg pte_addr_reg, 0, pteh_val_reg
-
-#if __SH5__ == 64
- .section .text,"ax"
-#define LOAD_ADDR(sym, reg) \
- movi (sym >> 48) & 65535, reg; \
- shori (sym >> 32) & 65535, reg; \
- shori (sym >> 16) & 65535, reg; \
- shori sym & 65535, reg
-#else
- .mode SHmedia
- .section .text..SHmedia32,"ax"
-#define LOAD_ADDR(sym, reg) \
- movi (sym >> 16) & 65535, reg; \
- shori sym & 65535, reg
-#endif
- .global start
-start:
- LOAD_ADDR (_stack, r15)
-
-#ifdef MMU_SUPPORT
- ! Set up the VM using the MMU and caches
-
- ! .vm_ep is first instruction to execute
- ! after VM initialization
- pt/l .vm_ep, tr1
-
- ! Configure instruction cache (ICCR)
- movi 3, r2
- movi 0, r3
- LOAD_ADDR (ICCR_BASE, r1)
- putcfg r1, 0, r2
- putcfg r1, 1, r3
-
- ! movi 7, r2 ! write through
- ! Configure operand cache (OCCR)
- LOAD_ADDR (OCCR_BASE, r1)
- putcfg r1, 0, r2
- putcfg r1, 1, r3
-
- ! Disable all PTE translations
- LOAD_ADDR (MMUIR_BASE, r1)
- LOAD_ADDR (MMUDR_BASE, r2)
- movi 64, r3
- pt/l .disable_ptes_loop, tr0
-.disable_ptes_loop:
- putcfg r1, 0, r63
- putcfg r2, 0, r63
- addi r1, 16, r1
- addi r2, 16, r2
- addi r3, -1, r3
- bgt r3, r63, tr0
-
- LOAD_ADDR (MMUIR_BASE, r1)
-
- ! FEMI instruction mappings
- ! Area 0 - 1Mb cacheable at 0x00000000
- ! Area 1 - None
- ! Area 2 - 1Mb cacheable at 0x05000000
- ! - 1Mb cacheable at 0x05100000
- ! Area 3 - None
- ! Area 4 - None
-
- ! Map a 1Mb page for instructions at 0x00000000
- LOAD_PTEH_VAL (FEMI_AREA_0, ALIGN_1MB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL (FEMI_AREA_0, ALIGN_1MB, PTE_CB_CACHEABLE_WB | PTE_SZ_1MB | PTE_PRX | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- ! Map a 1Mb page for instructions at 0x05000000
- addi r1, 16, r1
- LOAD_PTEH_VAL (FEMI_AREA_2, ALIGN_1MB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL (FEMI_AREA_2, ALIGN_1MB, PTE_CB_CACHEABLE_WB | PTE_SZ_1MB | PTE_PRX | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- ! Map a 1Mb page for instructions at 0x05100000
- addi r1, 16, r1
- LOAD_PTEH_VAL ((FEMI_AREA_2+0x100000), ALIGN_1MB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL ((FEMI_AREA_2+0x100000), ALIGN_1MB, PTE_CB_CACHEABLE_WB | PTE_SZ_1MB | PTE_PRX | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- ! Map a 512M page for instructions at EMI base
- addi r1, 16, r1
- LOAD_PTEH_VAL (EMI_BASE, ALIGN_512MB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL (EMI_BASE, ALIGN_512MB, PTE_CB_CACHEABLE_WB | PTE_SZ_512MB | PTE_PRX | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- ! Map a 4K page for instructions at DM_DB_DLINK_BASE
- addi r1, 16, r1
- LOAD_PTEH_VAL (DM_DB_DLINK_BASE, ALIGN_4KB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL (DM_DB_DLINK_BASE, ALIGN_4KB, PTE_CB_CACHEABLE_WB | PTE_SZ_4KB | PTE_PRX | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- LOAD_ADDR (MMUDR_BASE, r1)
-
- ! FEMI data mappings
- ! Area 0 - 1Mb cacheable at 0x00000000
- ! Area 1 - 1Mb device at 0x04000000
- ! Area 2 - 1Mb cacheable at 0x05000000
- ! - 1Mb cacheable at 0x05100000
- ! Area 3 - None
- ! Area 4 - None
- ! CB - 1Mb device at 0x08000000
-
- ! Map a 1Mb page for data at 0x00000000
- LOAD_PTEH_VAL (FEMI_AREA_0, ALIGN_1MB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL (FEMI_AREA_0, ALIGN_1MB, PTE_CB_CACHEABLE_WB | PTE_SZ_1MB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- ! Map a 1Mb page for data at 0x04000000
- addi r1, 16, r1
- LOAD_PTEH_VAL (FEMI_AREA_1, ALIGN_1MB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL (FEMI_AREA_1, ALIGN_1MB, PTE_CB_DEVICE | PTE_SZ_1MB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- ! Map a 1Mb page for data at 0x05000000
- addi r1, 16, r1
- LOAD_PTEH_VAL (FEMI_AREA_2, ALIGN_1MB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL (FEMI_AREA_2, ALIGN_1MB, PTE_CB_CACHEABLE_WB | PTE_SZ_1MB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- ! Map a 1Mb page for data at 0x05100000
- addi r1, 16, r1
- LOAD_PTEH_VAL ((FEMI_AREA_2+0x100000), ALIGN_1MB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL ((FEMI_AREA_2+0x100000), ALIGN_1MB, PTE_CB_CACHEABLE_WB | PTE_SZ_1MB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- ! Map a 4K page for registers at 0x08000000
- addi r1, 16, r1
- LOAD_PTEH_VAL (FEMI_CB, ALIGN_4KB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL (FEMI_CB, ALIGN_4KB, PTE_CB_DEVICE | PTE_SZ_4KB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- ! Map a 512M page for data at EMI
- addi r1, 16, r1
- LOAD_PTEH_VAL (EMI_BASE, ALIGN_512MB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL (EMI_BASE, ALIGN_512MB, PTE_CB_CACHEABLE_WB | PTE_SZ_512MB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- ! Map a 4K page for DYNACON at DYNACON_BASE
- addi r1, 16, r1
- LOAD_PTEH_VAL (DYNACON_BASE, ALIGN_4KB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL (DYNACON_BASE, ALIGN_4KB, PTE_CB_DEVICE | PTE_SZ_4KB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- ! Map a 4K page for instructions at DM_DB_DLINK_BASE
- addi r1, 16, r1
- LOAD_PTEH_VAL (DM_DB_DLINK_BASE, ALIGN_4KB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL (DM_DB_DLINK_BASE, ALIGN_4KB, PTE_CB_CACHEABLE_WB | PTE_SZ_4KB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- ! Map a 4K page for data at DM_DB_DLINK_BASE+0x1000
- addi r1, 16, r1
- LOAD_PTEH_VAL ((DM_DB_DLINK_BASE+0x1000), ALIGN_4KB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL ((DM_DB_DLINK_BASE+0x1000), ALIGN_4KB, PTE_CB_UNCACHEABLE | PTE_SZ_4KB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- ! Map a 4K page for stack DM_DB_DLINK_BASE+0x2000
- addi r1, 16, r1
- LOAD_PTEH_VAL ((DM_DB_DLINK_BASE+0x2000), ALIGN_4KB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL ((DM_DB_DLINK_BASE+0x2000), ALIGN_4KB, PTE_CB_CACHEABLE_WB | PTE_SZ_4KB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- ! Map a 1M page for DM_CB_BASE2 at DM_CB_DLINK
- ! 0x0c000000 - 0x0c0fffff
- addi r1, 16, r1
- LOAD_PTEH_VAL (DM_CB_DLINK_BASE, ALIGN_1MB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL (DM_CB_DLINK_BASE, ALIGN_1MB, PTE_CB_DEVICE | PTE_SZ_1MB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- ! Map a 1M page for DM_CB_BASE2 at DM_CB_DLINK
- ! 0x0c100000 - 0x0c1fffff
- addi r1, 16, r1
- LOAD_PTEH_VAL ((DM_CB_DLINK_BASE+0x100000), ALIGN_1MB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL ((DM_CB_DLINK_BASE+0x100000), ALIGN_1MB, PTE_CB_DEVICE | PTE_SZ_1MB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- ! Map a 1M page for DM_CB_BASE2 at DM_CB_DLINK
- ! 0x0c200000 - 0x0c2fffff
- addi r1, 16, r1
- LOAD_PTEH_VAL ((DM_CB_DLINK_BASE+0x200000), ALIGN_1MB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL ((DM_CB_DLINK_BASE+0x200000), ALIGN_1MB, PTE_CB_DEVICE | PTE_SZ_1MB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- ! Map a 1M page for DM_CB_BASE2 at DM_CB_DLINK
- ! 0x0c400000 - 0x0c4fffff
- addi r1, 16, r1
- LOAD_PTEH_VAL ((DM_CB_DLINK_BASE+0x400000), ALIGN_1MB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL ((DM_CB_DLINK_BASE+0x400000), ALIGN_1MB, PTE_CB_DEVICE | PTE_SZ_1MB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- ! Map a 1M page for DM_CB_BASE2 at DM_CB_DLINK
- ! 0x0c800000 - 0x0c8fffff
- addi r1, 16, r1
- LOAD_PTEH_VAL ((DM_CB_DLINK_BASE+0x800000), ALIGN_1MB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL ((DM_CB_DLINK_BASE+0x800000), ALIGN_1MB, PTE_CB_DEVICE | PTE_SZ_1MB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- ! Map a 4K page for DMA control registers
- addi r1, 16, r1
- LOAD_PTEH_VAL (DMA_BASE, ALIGN_4KB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL (DMA_BASE, ALIGN_4KB, PTE_CB_DEVICE | PTE_SZ_4KB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- ! Map lots of 4K pages for peripherals
-
- ! /* peripheral */
- addi r1, 16, r1
- LOAD_PTEH_VAL (PERIPH_BASE, ALIGN_4KB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL (PERIPH_BASE, ALIGN_4KB, PTE_CB_DEVICE | PTE_SZ_4KB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
- ! /* dmac */
- addi r1, 16, r1
- LOAD_PTEH_VAL (DMAC_BASE, ALIGN_4KB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL (DMAC_BASE, ALIGN_4KB, PTE_CB_DEVICE | PTE_SZ_4KB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
- ! /* intc */
- addi r1, 16, r1
- LOAD_PTEH_VAL (INTC_BASE, ALIGN_4KB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL (INTC_BASE, ALIGN_4KB, PTE_CB_DEVICE | PTE_SZ_4KB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
- ! /* rtc */
- addi r1, 16, r1
- LOAD_PTEH_VAL (RTC_BASE, ALIGN_4KB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL (RTC_BASE, ALIGN_4KB, PTE_CB_DEVICE | PTE_SZ_4KB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
- ! /* dmac */
- addi r1, 16, r1
- LOAD_PTEH_VAL (TMU_BASE, ALIGN_4KB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL (TMU_BASE, ALIGN_4KB, PTE_CB_DEVICE | PTE_SZ_4KB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
- ! /* scif */
- addi r1, 16, r1
- LOAD_PTEH_VAL (SCIF_BASE, ALIGN_4KB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL (SCIF_BASE, ALIGN_4KB, PTE_CB_DEVICE | PTE_SZ_4KB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
- ! /* cprc */
- addi r1, 16, r1
- LOAD_PTEH_VAL (CPRC_BASE, ALIGN_4KB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL (CPRC_BASE, ALIGN_4KB, PTE_CB_DEVICE | PTE_SZ_4KB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- ! Map CPU WPC registers
- addi r1, 16, r1
- LOAD_PTEH_VAL (CPU_BASE, ALIGN_1MB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL (CPU_BASE, ALIGN_1MB, PTE_CB_DEVICE | PTE_SZ_1MB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
- addi r1, 16, r1
-
- LOAD_PTEH_VAL ((CPU_BASE+0x100000), ALIGN_1MB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL ((CPU_BASE+0x100000), ALIGN_1MB, PTE_CB_DEVICE | PTE_SZ_1MB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- addi r1, 16, r1
- LOAD_PTEH_VAL ((CPU_BASE+0x200000), ALIGN_1MB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL ((CPU_BASE+0x200000), ALIGN_1MB, PTE_CB_DEVICE | PTE_SZ_1MB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- addi r1, 16, r1
- LOAD_PTEH_VAL ((CPU_BASE+0x400000), ALIGN_1MB, PTE_ENABLED | PTE_NOT_SHARED, r25, r2)
- LOAD_PTEL_VAL ((CPU_BASE+0x400000), ALIGN_1MB, PTE_CB_DEVICE | PTE_SZ_1MB | PTE_PRR | PTE_PRW | PTE_PRU, r25, r3)
- SET_PTE (r1, r2, r3)
-
- ! Switch over to virtual addressing and enabled cache
- getcon sr, r1
- movi 1, r2
- shlli r2, SR_BL_BIT, r2
- or r1, r2, r1
- putcon r1, ssr
- getcon sr, r1
- movi 1, r2
- shlli r2, SR_MMU_BIT, r2
- or r1, r2, r1
- putcon r1, ssr
- gettr tr1, r1
- putcon r1, spc
- synco
- rte
-
- ! VM entry point. From now on, we are in VM mode.
-.vm_ep:
-
- ! Install the trap handler, by seeding vbr with the
- ! correct value, and by assigning sr.bl = 0.
-
- LOAD_ADDR (vbr_start, r1)
- putcon r1, vbr
- movi ~(1<<28), r1
- getcon sr, r2
- and r1, r2, r2
- putcon r2, sr
-#endif /* MMU_SUPPORT */
-
- pt/l .Lzero_bss_loop, tr0
- pt/l GLOBAL(_init), tr5
- pt/l ___setup_argv_and_call_main, tr6
- pt/l _exit, tr7
-
- ! zero out bss
- LOAD_ADDR (_edata, r0)
- LOAD_ADDR (_end, r1)
-.Lzero_bss_loop:
- stx.q r0, r63, r63
- addi r0, 8, r0
- bgt/l r1, r0, tr0
-
- LOAD_ADDR (___data, r26)
- LOAD_ADDR (___rodata, r27)
-
-#ifdef __SH_FPU_ANY__
- getcon sr, r0
- ! enable the FP unit, by resetting SR.FD
- ! also zero out SR.FR, SR.SZ and SR.PR, as mandated by the ABI
- movi 0, r1
- shori 0xf000, r1
- andc r0, r1, r0
- putcon r0, sr
-#if __SH5__ == 32
- pt/l ___set_fpscr, tr0
- movi 0, r4
- blink tr0, r18
-#endif
-#endif
-
- ! arrange for exit to call fini
- pt/l _atexit, tr1
- LOAD_ADDR (GLOBAL(_fini), r2)
- blink tr1, r18
-
- ! call init
- blink tr5, r18
-
- ! call the mainline
- blink tr6, r18
-
- ! call exit
- blink tr7, r18
- ! We should never return from _exit but in case we do we would enter the
- ! the following tight loop. This avoids executing any data that might follow.
-limbo:
- pt/l limbo, tr0
- blink tr0, r63
-
-#ifdef MMU_SUPPORT
- ! All these traps are handled in the same place.
- .balign 256
-vbr_start:
- pt/l handler, tr0 ! tr0 trashed.
- blink tr0, r63
- .balign 256
-vbr_100:
- pt/l handler, tr0 ! tr0 trashed.
- blink tr0, r63
-vbr_100_end:
- .balign 256
-vbr_200:
- pt/l handler, tr0 ! tr0 trashed.
- blink tr0, r63
- .balign 256
-vbr_300:
- pt/l handler, tr0 ! tr0 trashed.
- blink tr0, r63
- .balign 256
-vbr_400: ! Should be at vbr+0x400
-handler:
- /* If the trap handler is there call it */
- LOAD_ADDR (__superh_trap_handler, r2)
- pta chandler,tr2
- beq r2, r63, tr2 /* If zero, ie not present branch around to chandler */
- /* Now call the trap handler with as much of the context unchanged as possible.
- Move trapping address into R18 to make it look like the trap point */
- getcon spc, r18
- pt/l __superh_trap_handler, tr0
- blink tr0, r7
-chandler:
- getcon spc, r62
- getcon expevt, r2
- pt/l _exit, tr0
- blink tr0, r63
-
- /* Simulated trap handler */
- .section .text..SHmedia32,"ax"
-gcc2_compiled.:
- .section .debug_abbrev
-.Ldebug_abbrev0:
- .section .text..SHmedia32
-.Ltext0:
- .section .debug_info
-.Ldebug_info0:
- .section .debug_line
-.Ldebug_line0:
- .section .text..SHmedia32,"ax"
- .align 5
- .global __superh_trap_handler
- .type __superh_trap_handler,@function
-__superh_trap_handler:
-.LFB1:
- ptabs r18, tr0
- addi.l r15, -8, r15
- st.l r15, 4, r14
- addi.l r15, -8, r15
- add.l r15, r63, r14
- st.l r14, 0, r2
- ptabs r7, tr0
- addi.l r14, 8, r14
- add.l r14, r63, r15
- ld.l r15, 4, r14
- addi.l r15, 8, r15
- blink tr0, r63
-.LFE1:
-.Lfe1:
- .size __superh_trap_handler,.Lfe1-__superh_trap_handler
-
- .section .text..SHmedia32
-.Letext0:
-
- .section .debug_info
- .ualong 0xa7
- .uaword 0x2
- .ualong .Ldebug_abbrev0
- .byte 0x4
- .byte 0x1
- .ualong .Ldebug_line0
- .ualong .Letext0
- .ualong .Ltext0
- .string "trap_handler.c"
-
- .string "xxxxxxxxxxxxxxxxxxxxxxxxxxxx"
-
- .string "GNU C 2.97-sh5-010522"
-
- .byte 0x1
- .byte 0x2
- .ualong 0x9a
- .byte 0x1
- .string "_superh_trap_handler"
-
- .byte 0x1
- .byte 0x2
- .byte 0x1
- .ualong .LFB1
- .ualong .LFE1
- .byte 0x1
- .byte 0x5e
- .byte 0x3
- .string "trap_reason"
-
- .byte 0x1
- .byte 0x1
- .ualong 0x9a
- .byte 0x2
- .byte 0x91
- .byte 0x0
- .byte 0x0
- .byte 0x4
- .string "unsigned int"
-
- .byte 0x4
- .byte 0x7
- .byte 0x0
-
- .section .debug_abbrev
- .byte 0x1
- .byte 0x11
- .byte 0x1
- .byte 0x10
- .byte 0x6
- .byte 0x12
- .byte 0x1
- .byte 0x11
- .byte 0x1
- .byte 0x3
- .byte 0x8
- .byte 0x1b
- .byte 0x8
- .byte 0x25
- .byte 0x8
- .byte 0x13
- .byte 0xb
- .byte 0,0
- .byte 0x2
- .byte 0x2e
- .byte 0x1
- .byte 0x1
- .byte 0x13
- .byte 0x3f
- .byte 0xc
- .byte 0x3
- .byte 0x8
- .byte 0x3a
- .byte 0xb
- .byte 0x3b
- .byte 0xb
- .byte 0x27
- .byte 0xc
- .byte 0x11
- .byte 0x1
- .byte 0x12
- .byte 0x1
- .byte 0x40
- .byte 0xa
- .byte 0,0
- .byte 0x3
- .byte 0x5
- .byte 0x0
- .byte 0x3
- .byte 0x8
- .byte 0x3a
- .byte 0xb
- .byte 0x3b
- .byte 0xb
- .byte 0x49
- .byte 0x13
- .byte 0x2
- .byte 0xa
- .byte 0,0
- .byte 0x4
- .byte 0x24
- .byte 0x0
- .byte 0x3
- .byte 0x8
- .byte 0xb
- .byte 0xb
- .byte 0x3e
- .byte 0xb
- .byte 0,0
- .byte 0
-
- .section .debug_pubnames
- .ualong 0x27
- .uaword 0x2
- .ualong .Ldebug_info0
- .ualong 0xab
- .ualong 0x5b
- .string "_superh_trap_handler"
-
- .ualong 0x0
-
- .section .debug_aranges
- .ualong 0x1c
- .uaword 0x2
- .ualong .Ldebug_info0
- .byte 0x4
- .byte 0x0
- .uaword 0x0,0
- .ualong .Ltext0
- .ualong .Letext0-.Ltext0
- .ualong 0x0
- .ualong 0x0
- .ident "GCC: (GNU) 2.97-sh5-010522"
-#endif /* MMU_SUPPORT */
-#else /* ! __SH5__ */
-
! make a place to keep any previous value of the vbr register
! this will only have a value if it has been set by redboot (for example)
.section .bss
@@ -1364,4 +722,3 @@ __superh_trap_handler:
.ualong 0x0
.ualong 0x0
#endif /* VBR_SETUP */
-#endif /* ! __SH5__ */
diff --git a/libgcc/config/sh/crti.S b/libgcc/config/sh/crti.S
index 0c7a28b..44e8dd5 100644
--- a/libgcc/config/sh/crti.S
+++ b/libgcc/config/sh/crti.S
@@ -47,19 +47,6 @@ see the files COPYING3 and COPYING.RUNTIME respectively. If not, see
#endif
.global GLOBAL(_init)
GLOBAL(_init):
-#if __SHMEDIA__
- addi r15, -16, r15
- st.q r15, 8, r14
- st.q r15, 0, r18
- add r15, r63, r14
-#elif __SH5__ && ! __SHMEDIA__
- mov r15,r0
- add #-8,r15
- mov.l r14,@-r0
- sts.l pr,@-r0
- mov r15,r14
- nop
-#else
#ifdef __ELF__
mov.l r12,@-r15
mova 0f,r0
@@ -78,7 +65,6 @@ GLOBAL(_init):
0: .long _GLOBAL_OFFSET_TABLE_
1:
#endif
-#endif /* __SHMEDIA__ */
.section .fini
/* The alignment below can't be smaller, otherwise the mova below
@@ -92,19 +78,6 @@ GLOBAL(_init):
#endif
.global GLOBAL(_fini)
GLOBAL(_fini):
-#if __SHMEDIA__
- addi r15, -16, r15
- st.q r15, 8, r14
- st.q r15, 0, r18
- add r15, r63, r14
-#elif __SH5__ && ! __SHMEDIA__
- mov r15,r0
- add #-8,r15
- mov.l r14,@-r0
- sts.l pr,@-r0
- mov r15,r14
- nop
-#else
#ifdef __ELF__
mov.l r12,@-r15
mova 0f,r0
@@ -123,4 +96,3 @@ GLOBAL(_fini):
0: .long _GLOBAL_OFFSET_TABLE_
1:
#endif
-#endif /* __SHMEDIA__ */
diff --git a/libgcc/config/sh/crtn.S b/libgcc/config/sh/crtn.S
index 1ca76c8..63b8421 100644
--- a/libgcc/config/sh/crtn.S
+++ b/libgcc/config/sh/crtn.S
@@ -25,20 +25,6 @@ see the files COPYING3 and COPYING.RUNTIME respectively. If not, see
/* See an explanation about .init and .fini in crti.S. */
.section .init
-#if __SHMEDIA__
- add r14, r63, r15
- ld.q r15, 0, r18
- ptabs r18, tr0
- ld.q r15, 8, r14
- addi r15, 16, r15
- blink tr0, r63
-#elif __SH5__ && ! __SHMEDIA__
- mov r14,r15
- lds.l @r14+,pr
- mov.l @r14,r14
- rts
- add #8,r15
-#else
mov r14,r15
lds.l @r15+,pr
mov.l @r15+,r14
@@ -48,23 +34,8 @@ see the files COPYING3 and COPYING.RUNTIME respectively. If not, see
#else
nop
#endif
-#endif /* __SHMEDIA__ */
.section .fini
-#if __SHMEDIA__
- add r14, r63, r15
- ld.q r15, 0, r18
- ptabs r18, tr0
- ld.q r15, 8, r14
- addi r15, 16, r15
- blink tr0, r63
-#elif __SH5__ && ! __SHMEDIA__
- mov r14,r15
- lds.l @r14+,pr
- mov.l @r14,r14
- rts
- add #8,r15
-#else
mov r14,r15
lds.l @r15+,pr
mov.l @r15+,r14
@@ -74,4 +45,3 @@ see the files COPYING3 and COPYING.RUNTIME respectively. If not, see
#else
nop
#endif
-#endif /* __SHMEDIA__ */
diff --git a/libgcc/config/sh/lib1funcs-4-300.S b/libgcc/config/sh/lib1funcs-4-300.S
index caf49f7..651567b 100644
--- a/libgcc/config/sh/lib1funcs-4-300.S
+++ b/libgcc/config/sh/lib1funcs-4-300.S
@@ -25,7 +25,6 @@ see the files COPYING3 and COPYING.RUNTIME respectively. If not, see
#include "lib1funcs.h"
-#if !__SHMEDIA__
#ifdef L_div_table
#if defined (__SH3__) || defined (__SH3E__) || defined (__SH4__) || defined (__SH4_SINGLE__) || defined (__SH4_SINGLE_ONLY__) || defined (__SH4_NOFPU__)
/* This code used shld, thus is not suitable for SH1 / SH2. */
@@ -933,4 +932,3 @@ LOCAL(div_table_inv):
#endif /* SH3 / SH4 */
#endif /* L_div_table */
-#endif /* !__SHMEDIA__ */
diff --git a/libgcc/config/sh/lib1funcs-Os-4-200.S b/libgcc/config/sh/lib1funcs-Os-4-200.S
index 1cb826f..4fcd8a6 100644
--- a/libgcc/config/sh/lib1funcs-Os-4-200.S
+++ b/libgcc/config/sh/lib1funcs-Os-4-200.S
@@ -25,7 +25,6 @@ see the files COPYING3 and COPYING.RUNTIME respectively. If not, see
#include "lib1funcs.h"
-#if !__SHMEDIA__
#ifdef L_udivsi3_i4i
/* 88 bytes; sh4-200 cycle counts:
@@ -319,4 +318,3 @@ L1:
ENDFUNC(GLOBAL(sdivsi3_i4i))
#endif /* __SH_FPU_DOUBLE__ */
#endif /* L_sdivsi3_i4i */
-#endif /* !__SHMEDIA__ */
diff --git a/libgcc/config/sh/lib1funcs.S b/libgcc/config/sh/lib1funcs.S
index 905e5ef..33dd5fd 100644
--- a/libgcc/config/sh/lib1funcs.S
+++ b/libgcc/config/sh/lib1funcs.S
@@ -46,7 +46,6 @@ see the files COPYING3 and COPYING.RUNTIME respectively. If not, see
#define NO_FPSCR_VALUES
#endif
-#if ! __SH5__
#ifdef L_ashiftrt
.global GLOBAL(ashiftrt_r4_0)
.global GLOBAL(ashiftrt_r4_1)
@@ -1002,7 +1001,6 @@ hiset: sts macl,r0 ! r0 = bb*dd
ENDFUNC(GLOBAL(mulsi3))
#endif
-#endif /* ! __SH5__ */
/*------------------------------------------------------------------------------
32 bit signed integer division that uses FPU double precision division. */
@@ -1028,17 +1026,13 @@ GLOBAL(sdivsi3_i4):
ENDFUNC(GLOBAL(sdivsi3_i4))
-#elif defined (__SH2A_SINGLE__) || defined (__SH2A_SINGLE_ONLY__) || defined(__SH4_SINGLE__) || defined(__SH4_SINGLE_ONLY__) || (defined (__SH5__) && ! defined __SH4_NOFPU__)
+#elif defined (__SH2A_SINGLE__) || defined (__SH2A_SINGLE_ONLY__) || defined(__SH4_SINGLE__) || defined(__SH4_SINGLE_ONLY__)
/* This variant is used when FPSCR.PR = 0 (sigle precision) is the default
setting.
Args in r4 and r5, result in fpul, clobber r2, dr0, dr2.
For this to work, we must temporarily switch the FPU do double precision,
but we better do not touch FPSCR.FR. See PR 6526. */
-#if ! __SH5__ || __SH5__ == 32
-#if __SH5__
- .mode SHcompact
-#endif
.global GLOBAL(sdivsi3_i4)
HIDDEN_FUNC(GLOBAL(sdivsi3_i4))
GLOBAL(sdivsi3_i4):
@@ -1074,7 +1068,6 @@ GLOBAL(sdivsi3_i4):
#endif /* __SH4A__ */
ENDFUNC(GLOBAL(sdivsi3_i4))
-#endif /* ! __SH5__ || __SH5__ == 32 */
#endif /* ! __SH4__ || __SH2A__ */
#endif /* L_sdivsi3_i4 */
@@ -1091,226 +1084,8 @@ GLOBAL(sdivsi3_i4):
!! args in r4 and r5, result in r0 clobber r1, r2, r3, and t bit
.global GLOBAL(sdivsi3)
-#if __SHMEDIA__
-#if __SH5__ == 32
- .section .text..SHmedia32,"ax"
-#else
- .text
-#endif
.align 2
-#if 0
-/* The assembly code that follows is a hand-optimized version of the C
- code that follows. Note that the registers that are modified are
- exactly those listed as clobbered in the patterns divsi3_i1 and
- divsi3_i1_media.
-
-int __sdivsi3 (i, j)
- int i, j;
-{
- register unsigned long long r18 asm ("r18");
- register unsigned long long r19 asm ("r19");
- register unsigned long long r0 asm ("r0") = 0;
- register unsigned long long r1 asm ("r1") = 1;
- register int r2 asm ("r2") = i >> 31;
- register int r3 asm ("r3") = j >> 31;
-
- r2 = r2 ? r2 : r1;
- r3 = r3 ? r3 : r1;
- r18 = i * r2;
- r19 = j * r3;
- r2 *= r3;
-
- r19 <<= 31;
- r1 <<= 31;
- do
- if (r18 >= r19)
- r0 |= r1, r18 -= r19;
- while (r19 >>= 1, r1 >>= 1);
-
- return r2 * (int)r0;
-}
-*/
-GLOBAL(sdivsi3):
- pt/l LOCAL(sdivsi3_dontadd), tr2
- pt/l LOCAL(sdivsi3_loop), tr1
- ptabs/l r18, tr0
- movi 0, r0
- movi 1, r1
- shari.l r4, 31, r2
- shari.l r5, 31, r3
- cmveq r2, r1, r2
- cmveq r3, r1, r3
- muls.l r4, r2, r18
- muls.l r5, r3, r19
- muls.l r2, r3, r2
- shlli r19, 31, r19
- shlli r1, 31, r1
-LOCAL(sdivsi3_loop):
- bgtu r19, r18, tr2
- or r0, r1, r0
- sub r18, r19, r18
-LOCAL(sdivsi3_dontadd):
- shlri r1, 1, r1
- shlri r19, 1, r19
- bnei r1, 0, tr1
- muls.l r0, r2, r0
- add.l r0, r63, r0
- blink tr0, r63
-#elif 0 /* ! 0 */
- // inputs: r4,r5
- // clobbered: r1,r2,r3,r18,r19,r20,r21,r25,tr0
- // result in r0
-GLOBAL(sdivsi3):
- // can create absolute value without extra latency,
- // but dependent on proper sign extension of inputs:
- // shari.l r5,31,r2
- // xor r5,r2,r20
- // sub r20,r2,r20 // r20 is now absolute value of r5, zero-extended.
- shari.l r5,31,r2
- ori r2,1,r2
- muls.l r5,r2,r20 // r20 is now absolute value of r5, zero-extended.
- movi 0xffffffffffffbb0c,r19 // shift count eqiv 76
- shari.l r4,31,r3
- nsb r20,r0
- shlld r20,r0,r25
- shlri r25,48,r25
- sub r19,r25,r1
- mmulfx.w r1,r1,r2
- mshflo.w r1,r63,r1
- // If r4 was to be used in-place instead of r21, could use this sequence
- // to compute absolute:
- // sub r63,r4,r19 // compute absolute value of r4
- // shlri r4,32,r3 // into lower 32 bit of r4, keeping
- // mcmv r19,r3,r4 // the sign in the upper 32 bits intact.
- ori r3,1,r3
- mmulfx.w r25,r2,r2
- sub r19,r0,r0
- muls.l r4,r3,r21
- msub.w r1,r2,r2
- addi r2,-2,r1
- mulu.l r21,r1,r19
- mmulfx.w r2,r2,r2
- shlli r1,15,r1
- shlrd r19,r0,r19
- mulu.l r19,r20,r3
- mmacnfx.wl r25,r2,r1
- ptabs r18,tr0
- sub r21,r3,r25
-
- mulu.l r25,r1,r2
- addi r0,14,r0
- xor r4,r5,r18
- shlrd r2,r0,r2
- mulu.l r2,r20,r3
- add r19,r2,r19
- shari.l r18,31,r18
- sub r25,r3,r25
-
- mulu.l r25,r1,r2
- sub r25,r20,r25
- add r19,r18,r19
- shlrd r2,r0,r2
- mulu.l r2,r20,r3
- addi r25,1,r25
- add r19,r2,r19
-
- cmpgt r25,r3,r25
- add.l r19,r25,r0
- xor r0,r18,r0
- blink tr0,r63
-#else /* ! 0 && ! 0 */
-
- // inputs: r4,r5
- // clobbered: r1,r18,r19,r20,r21,r25,tr0
- // result in r0
- HIDDEN_FUNC(GLOBAL(sdivsi3_2))
-#ifndef __pic__
- FUNC(GLOBAL(sdivsi3))
-GLOBAL(sdivsi3): /* this is the shcompact entry point */
- // The special SHmedia entry point sdivsi3_1 prevents accidental linking
- // with the SHcompact implementation, which clobbers tr1 / tr2.
- .global GLOBAL(sdivsi3_1)
-GLOBAL(sdivsi3_1):
- .global GLOBAL(div_table_internal)
- movi (GLOBAL(div_table_internal) >> 16) & 65535, r20
- shori GLOBAL(div_table_internal) & 65535, r20
-#endif
- .global GLOBAL(sdivsi3_2)
- // div_table in r20
- // clobbered: r1,r18,r19,r21,r25,tr0
-GLOBAL(sdivsi3_2):
- nsb r5, r1
- shlld r5, r1, r25 // normalize; [-2 ..1, 1..2) in s2.62
- shari r25, 58, r21 // extract 5(6) bit index (s2.4 with hole -1..1)
- ldx.ub r20, r21, r19 // u0.8
- shari r25, 32, r25 // normalize to s2.30
- shlli r21, 1, r21
- muls.l r25, r19, r19 // s2.38
- ldx.w r20, r21, r21 // s2.14
- ptabs r18, tr0
- shari r19, 24, r19 // truncate to s2.14
- sub r21, r19, r19 // some 11 bit inverse in s1.14
- muls.l r19, r19, r21 // u0.28
- sub r63, r1, r1
- addi r1, 92, r1
- muls.l r25, r21, r18 // s2.58
- shlli r19, 45, r19 // multiply by two and convert to s2.58
- /* bubble */
- sub r19, r18, r18
- shari r18, 28, r18 // some 22 bit inverse in s1.30
- muls.l r18, r25, r0 // s2.60
- muls.l r18, r4, r25 // s32.30
- /* bubble */
- shari r0, 16, r19 // s-16.44
- muls.l r19, r18, r19 // s-16.74
- shari r25, 63, r0
- shari r4, 14, r18 // s19.-14
- shari r19, 30, r19 // s-16.44
- muls.l r19, r18, r19 // s15.30
- xor r21, r0, r21 // You could also use the constant 1 << 27.
- add r21, r25, r21
- sub r21, r19, r21
- shard r21, r1, r21
- sub r21, r0, r0
- blink tr0, r63
-#ifndef __pic__
- ENDFUNC(GLOBAL(sdivsi3))
-#endif
- ENDFUNC(GLOBAL(sdivsi3_2))
-#endif
-#elif __SHMEDIA__
-/* m5compact-nofpu */
- // clobbered: r18,r19,r20,r21,r25,tr0,tr1,tr2
- .mode SHmedia
- .section .text..SHmedia32,"ax"
- .align 2
- FUNC(GLOBAL(sdivsi3))
-GLOBAL(sdivsi3):
- pt/l LOCAL(sdivsi3_dontsub), tr0
- pt/l LOCAL(sdivsi3_loop), tr1
- ptabs/l r18,tr2
- shari.l r4,31,r18
- shari.l r5,31,r19
- xor r4,r18,r20
- xor r5,r19,r21
- sub.l r20,r18,r20
- sub.l r21,r19,r21
- xor r18,r19,r19
- shlli r21,32,r25
- addi r25,-1,r21
- addz.l r20,r63,r20
-LOCAL(sdivsi3_loop):
- shlli r20,1,r20
- bgeu/u r21,r20,tr0
- sub r20,r21,r20
-LOCAL(sdivsi3_dontsub):
- addi.l r25,-1,r25
- bnei r25,-32,tr1
- xor r20,r19,r20
- sub.l r20,r19,r0
- blink tr2,r63
- ENDFUNC(GLOBAL(sdivsi3))
-#else /* ! __SHMEDIA__ */
+
FUNC(GLOBAL(sdivsi3))
GLOBAL(sdivsi3):
mov r4,r1
@@ -1397,7 +1172,6 @@ div0: rts
mov #0,r0
ENDFUNC(GLOBAL(sdivsi3))
-#endif /* ! __SHMEDIA__ */
#endif /* L_sdivsi3 */
/*------------------------------------------------------------------------------
@@ -1451,28 +1225,6 @@ L1:
ENDFUNC(GLOBAL(udivsi3_i4))
-#elif defined (__SH5__) && ! defined (__SH4_NOFPU__) && ! defined (__SH2A_NOFPU__)
-#if ! __SH5__ || __SH5__ == 32
-!! args in r4 and r5, result in fpul, clobber r20, r21, dr0, fr33
- .mode SHmedia
- .global GLOBAL(udivsi3_i4)
- HIDDEN_FUNC(GLOBAL(udivsi3_i4))
-GLOBAL(udivsi3_i4):
- addz.l r4,r63,r20
- addz.l r5,r63,r21
- fmov.qd r20,dr0
- fmov.qd r21,dr32
- ptabs r18,tr0
- float.qd dr0,dr0
- float.qd dr32,dr32
- fdiv.d dr0,dr32,dr0
- ftrc.dq dr0,dr32
- fmov.s fr33,fr32
- blink tr0,r63
-
- ENDFUNC(GLOBAL(udivsi3_i4))
-#endif /* ! __SH5__ || __SH5__ == 32 */
-
#elif defined (__SH2A_SINGLE__) || defined (__SH2A_SINGLE_ONLY__) || defined(__SH4_SINGLE__) || defined(__SH4_SINGLE_ONLY__)
/* This variant is used when FPSCR.PR = 0 (sigle precision) is the default
setting.
@@ -1581,133 +1333,6 @@ L1:
.global GLOBAL(udivsi3)
HIDDEN_FUNC(GLOBAL(udivsi3))
-#if __SHMEDIA__
-#if __SH5__ == 32
- .section .text..SHmedia32,"ax"
-#else
- .text
-#endif
- .align 2
-#if 0
-/* The assembly code that follows is a hand-optimized version of the C
- code that follows. Note that the registers that are modified are
- exactly those listed as clobbered in the patterns udivsi3_i1 and
- udivsi3_i1_media.
-
-unsigned
-__udivsi3 (i, j)
- unsigned i, j;
-{
- register unsigned long long r0 asm ("r0") = 0;
- register unsigned long long r18 asm ("r18") = 1;
- register unsigned long long r4 asm ("r4") = i;
- register unsigned long long r19 asm ("r19") = j;
-
- r19 <<= 31;
- r18 <<= 31;
- do
- if (r4 >= r19)
- r0 |= r18, r4 -= r19;
- while (r19 >>= 1, r18 >>= 1);
-
- return r0;
-}
-*/
-GLOBAL(udivsi3):
- pt/l LOCAL(udivsi3_dontadd), tr2
- pt/l LOCAL(udivsi3_loop), tr1
- ptabs/l r18, tr0
- movi 0, r0
- movi 1, r18
- addz.l r5, r63, r19
- addz.l r4, r63, r4
- shlli r19, 31, r19
- shlli r18, 31, r18
-LOCAL(udivsi3_loop):
- bgtu r19, r4, tr2
- or r0, r18, r0
- sub r4, r19, r4
-LOCAL(udivsi3_dontadd):
- shlri r18, 1, r18
- shlri r19, 1, r19
- bnei r18, 0, tr1
- blink tr0, r63
-#else
-GLOBAL(udivsi3):
- // inputs: r4,r5
- // clobbered: r18,r19,r20,r21,r22,r25,tr0
- // result in r0.
- addz.l r5,r63,r22
- nsb r22,r0
- shlld r22,r0,r25
- shlri r25,48,r25
- movi 0xffffffffffffbb0c,r20 // shift count eqiv 76
- sub r20,r25,r21
- mmulfx.w r21,r21,r19
- mshflo.w r21,r63,r21
- ptabs r18,tr0
- mmulfx.w r25,r19,r19
- sub r20,r0,r0
- /* bubble */
- msub.w r21,r19,r19
- addi r19,-2,r21 /* It would be nice for scheduling to do this add to r21
- before the msub.w, but we need a different value for
- r19 to keep errors under control. */
- mulu.l r4,r21,r18
- mmulfx.w r19,r19,r19
- shlli r21,15,r21
- shlrd r18,r0,r18
- mulu.l r18,r22,r20
- mmacnfx.wl r25,r19,r21
- /* bubble */
- sub r4,r20,r25
-
- mulu.l r25,r21,r19
- addi r0,14,r0
- /* bubble */
- shlrd r19,r0,r19
- mulu.l r19,r22,r20
- add r18,r19,r18
- /* bubble */
- sub.l r25,r20,r25
-
- mulu.l r25,r21,r19
- addz.l r25,r63,r25
- sub r25,r22,r25
- shlrd r19,r0,r19
- mulu.l r19,r22,r20
- addi r25,1,r25
- add r18,r19,r18
-
- cmpgt r25,r20,r25
- add.l r18,r25,r0
- blink tr0,r63
-#endif
-#elif __SHMEDIA__
-/* m5compact-nofpu - more emphasis on code size than on speed, but don't
- ignore speed altogether - div1 needs 9 cycles, subc 7 and rotcl 4.
- So use a short shmedia loop. */
- // clobbered: r20,r21,r25,tr0,tr1,tr2
- .mode SHmedia
- .section .text..SHmedia32,"ax"
- .align 2
-GLOBAL(udivsi3):
- pt/l LOCAL(udivsi3_dontsub), tr0
- pt/l LOCAL(udivsi3_loop), tr1
- ptabs/l r18,tr2
- shlli r5,32,r25
- addi r25,-1,r21
- addz.l r4,r63,r20
-LOCAL(udivsi3_loop):
- shlli r20,1,r20
- bgeu/u r21,r20,tr0
- sub r20,r21,r20
-LOCAL(udivsi3_dontsub):
- addi.l r25,-1,r25
- bnei r25,-32,tr1
- add.l r20,r63,r0
- blink tr2,r63
-#else /* ! __SHMEDIA__ */
LOCAL(div8):
div1 r5,r4
LOCAL(div7):
@@ -1769,320 +1394,11 @@ LOCAL(large_divisor):
rotcl r0
ENDFUNC(GLOBAL(udivsi3))
-#endif /* ! __SHMEDIA__ */
#endif /* L_udivsi3 */
-#ifdef L_udivdi3
-#if __SHMEDIA__
- .mode SHmedia
- .section .text..SHmedia32,"ax"
- .align 2
- .global GLOBAL(udivdi3)
- FUNC(GLOBAL(udivdi3))
-GLOBAL(udivdi3):
- HIDDEN_ALIAS(udivdi3_internal,udivdi3)
- shlri r3,1,r4
- nsb r4,r22
- shlld r3,r22,r6
- shlri r6,49,r5
- movi 0xffffffffffffbaf1,r21 /* .l shift count 17. */
- sub r21,r5,r1
- mmulfx.w r1,r1,r4
- mshflo.w r1,r63,r1
- sub r63,r22,r20 // r63 == 64 % 64
- mmulfx.w r5,r4,r4
- pta LOCAL(large_divisor),tr0
- addi r20,32,r9
- msub.w r1,r4,r1
- madd.w r1,r1,r1
- mmulfx.w r1,r1,r4
- shlri r6,32,r7
- bgt/u r9,r63,tr0 // large_divisor
- mmulfx.w r5,r4,r4
- shlri r2,32+14,r19
- addi r22,-31,r0
- msub.w r1,r4,r1
-
- mulu.l r1,r7,r4
- addi r1,-3,r5
- mulu.l r5,r19,r5
- sub r63,r4,r4 // Negate to make sure r1 ends up <= 1/r2
- shlri r4,2,r4 /* chop off leading %0000000000000000 001.00000000000 - or, as
- the case may be, %0000000000000000 000.11111111111, still */
- muls.l r1,r4,r4 /* leaving at least one sign bit. */
- mulu.l r5,r3,r8
- mshalds.l r1,r21,r1
- shari r4,26,r4
- shlld r8,r0,r8
- add r1,r4,r1 // 31 bit unsigned reciprocal now in r1 (msb equiv. 0.5)
- sub r2,r8,r2
- /* Can do second step of 64 : 32 div now, using r1 and the rest in r2. */
-
- shlri r2,22,r21
- mulu.l r21,r1,r21
- shlld r5,r0,r8
- addi r20,30-22,r0
- shlrd r21,r0,r21
- mulu.l r21,r3,r5
- add r8,r21,r8
- mcmpgt.l r21,r63,r21 // See Note 1
- addi r20,30,r0
- mshfhi.l r63,r21,r21
- sub r2,r5,r2
- andc r2,r21,r2
-
- /* small divisor: need a third divide step */
- mulu.l r2,r1,r7
- ptabs r18,tr0
- addi r2,1,r2
- shlrd r7,r0,r7
- mulu.l r7,r3,r5
- add r8,r7,r8
- sub r2,r3,r2
- cmpgt r2,r5,r5
- add r8,r5,r2
- /* could test r3 here to check for divide by zero. */
- blink tr0,r63
-
-LOCAL(large_divisor):
- mmulfx.w r5,r4,r4
- shlrd r2,r9,r25
- shlri r25,32,r8
- msub.w r1,r4,r1
-
- mulu.l r1,r7,r4
- addi r1,-3,r5
- mulu.l r5,r8,r5
- sub r63,r4,r4 // Negate to make sure r1 ends up <= 1/r2
- shlri r4,2,r4 /* chop off leading %0000000000000000 001.00000000000 - or, as
- the case may be, %0000000000000000 000.11111111111, still */
- muls.l r1,r4,r4 /* leaving at least one sign bit. */
- shlri r5,14-1,r8
- mulu.l r8,r7,r5
- mshalds.l r1,r21,r1
- shari r4,26,r4
- add r1,r4,r1 // 31 bit unsigned reciprocal now in r1 (msb equiv. 0.5)
- sub r25,r5,r25
- /* Can do second step of 64 : 32 div now, using r1 and the rest in r25. */
-
- shlri r25,22,r21
- mulu.l r21,r1,r21
- pta LOCAL(no_lo_adj),tr0
- addi r22,32,r0
- shlri r21,40,r21
- mulu.l r21,r7,r5
- add r8,r21,r8
- shlld r2,r0,r2
- sub r25,r5,r25
- bgtu/u r7,r25,tr0 // no_lo_adj
- addi r8,1,r8
- sub r25,r7,r25
-LOCAL(no_lo_adj):
- mextr4 r2,r25,r2
-
- /* large_divisor: only needs a few adjustments. */
- mulu.l r8,r6,r5
- ptabs r18,tr0
- /* bubble */
- cmpgtu r5,r2,r5
- sub r8,r5,r2
- blink tr0,r63
- ENDFUNC(GLOBAL(udivdi3))
-/* Note 1: To shift the result of the second divide stage so that the result
- always fits into 32 bits, yet we still reduce the rest sufficiently
- would require a lot of instructions to do the shifts just right. Using
- the full 64 bit shift result to multiply with the divisor would require
- four extra instructions for the upper 32 bits (shift / mulu / shift / sub).
- Fortunately, if the upper 32 bits of the shift result are nonzero, we
- know that the rest after taking this partial result into account will
- fit into 32 bits. So we just clear the upper 32 bits of the rest if the
- upper 32 bits of the partial result are nonzero. */
-#endif /* __SHMEDIA__ */
-#endif /* L_udivdi3 */
-
-#ifdef L_divdi3
-#if __SHMEDIA__
- .mode SHmedia
- .section .text..SHmedia32,"ax"
- .align 2
- .global GLOBAL(divdi3)
- FUNC(GLOBAL(divdi3))
-GLOBAL(divdi3):
- pta GLOBAL(udivdi3_internal),tr0
- shari r2,63,r22
- shari r3,63,r23
- xor r2,r22,r2
- xor r3,r23,r3
- sub r2,r22,r2
- sub r3,r23,r3
- beq/u r22,r23,tr0
- ptabs r18,tr1
- blink tr0,r18
- sub r63,r2,r2
- blink tr1,r63
- ENDFUNC(GLOBAL(divdi3))
-#endif /* __SHMEDIA__ */
-#endif /* L_divdi3 */
-
-#ifdef L_umoddi3
-#if __SHMEDIA__
- .mode SHmedia
- .section .text..SHmedia32,"ax"
- .align 2
- .global GLOBAL(umoddi3)
- FUNC(GLOBAL(umoddi3))
-GLOBAL(umoddi3):
- HIDDEN_ALIAS(umoddi3_internal,umoddi3)
- shlri r3,1,r4
- nsb r4,r22
- shlld r3,r22,r6
- shlri r6,49,r5
- movi 0xffffffffffffbaf1,r21 /* .l shift count 17. */
- sub r21,r5,r1
- mmulfx.w r1,r1,r4
- mshflo.w r1,r63,r1
- sub r63,r22,r20 // r63 == 64 % 64
- mmulfx.w r5,r4,r4
- pta LOCAL(large_divisor),tr0
- addi r20,32,r9
- msub.w r1,r4,r1
- madd.w r1,r1,r1
- mmulfx.w r1,r1,r4
- shlri r6,32,r7
- bgt/u r9,r63,tr0 // large_divisor
- mmulfx.w r5,r4,r4
- shlri r2,32+14,r19
- addi r22,-31,r0
- msub.w r1,r4,r1
-
- mulu.l r1,r7,r4
- addi r1,-3,r5
- mulu.l r5,r19,r5
- sub r63,r4,r4 // Negate to make sure r1 ends up <= 1/r2
- shlri r4,2,r4 /* chop off leading %0000000000000000 001.00000000000 - or, as
- the case may be, %0000000000000000 000.11111111111, still */
- muls.l r1,r4,r4 /* leaving at least one sign bit. */
- mulu.l r5,r3,r5
- mshalds.l r1,r21,r1
- shari r4,26,r4
- shlld r5,r0,r5
- add r1,r4,r1 // 31 bit unsigned reciprocal now in r1 (msb equiv. 0.5)
- sub r2,r5,r2
- /* Can do second step of 64 : 32 div now, using r1 and the rest in r2. */
-
- shlri r2,22,r21
- mulu.l r21,r1,r21
- addi r20,30-22,r0
- /* bubble */ /* could test r3 here to check for divide by zero. */
- shlrd r21,r0,r21
- mulu.l r21,r3,r5
- mcmpgt.l r21,r63,r21 // See Note 1
- addi r20,30,r0
- mshfhi.l r63,r21,r21
- sub r2,r5,r2
- andc r2,r21,r2
-
- /* small divisor: need a third divide step */
- mulu.l r2,r1,r7
- ptabs r18,tr0
- sub r2,r3,r8 /* re-use r8 here for rest - r3 */
- shlrd r7,r0,r7
- mulu.l r7,r3,r5
- /* bubble */
- addi r8,1,r7
- cmpgt r7,r5,r7
- cmvne r7,r8,r2
- sub r2,r5,r2
- blink tr0,r63
-
-LOCAL(large_divisor):
- mmulfx.w r5,r4,r4
- shlrd r2,r9,r25
- shlri r25,32,r8
- msub.w r1,r4,r1
-
- mulu.l r1,r7,r4
- addi r1,-3,r5
- mulu.l r5,r8,r5
- sub r63,r4,r4 // Negate to make sure r1 ends up <= 1/r2
- shlri r4,2,r4 /* chop off leading %0000000000000000 001.00000000000 - or, as
- the case may be, %0000000000000000 000.11111111111, still */
- muls.l r1,r4,r4 /* leaving at least one sign bit. */
- shlri r5,14-1,r8
- mulu.l r8,r7,r5
- mshalds.l r1,r21,r1
- shari r4,26,r4
- add r1,r4,r1 // 31 bit unsigned reciprocal now in r1 (msb equiv. 0.5)
- sub r25,r5,r25
- /* Can do second step of 64 : 32 div now, using r1 and the rest in r25. */
-
- shlri r25,22,r21
- mulu.l r21,r1,r21
- pta LOCAL(no_lo_adj),tr0
- addi r22,32,r0
- shlri r21,40,r21
- mulu.l r21,r7,r5
- add r8,r21,r8
- shlld r2,r0,r2
- sub r25,r5,r25
- bgtu/u r7,r25,tr0 // no_lo_adj
- addi r8,1,r8
- sub r25,r7,r25
-LOCAL(no_lo_adj):
- mextr4 r2,r25,r2
-
- /* large_divisor: only needs a few adjustments. */
- mulu.l r8,r6,r5
- ptabs r18,tr0
- add r2,r6,r7
- cmpgtu r5,r2,r8
- cmvne r8,r7,r2
- sub r2,r5,r2
- shlrd r2,r22,r2
- blink tr0,r63
- ENDFUNC(GLOBAL(umoddi3))
-/* Note 1: To shift the result of the second divide stage so that the result
- always fits into 32 bits, yet we still reduce the rest sufficiently
- would require a lot of instructions to do the shifts just right. Using
- the full 64 bit shift result to multiply with the divisor would require
- four extra instructions for the upper 32 bits (shift / mulu / shift / sub).
- Fortunately, if the upper 32 bits of the shift result are nonzero, we
- know that the rest after taking this partial result into account will
- fit into 32 bits. So we just clear the upper 32 bits of the rest if the
- upper 32 bits of the partial result are nonzero. */
-#endif /* __SHMEDIA__ */
-#endif /* L_umoddi3 */
-
-#ifdef L_moddi3
-#if __SHMEDIA__
- .mode SHmedia
- .section .text..SHmedia32,"ax"
- .align 2
- .global GLOBAL(moddi3)
- FUNC(GLOBAL(moddi3))
-GLOBAL(moddi3):
- pta GLOBAL(umoddi3_internal),tr0
- shari r2,63,r22
- shari r3,63,r23
- xor r2,r22,r2
- xor r3,r23,r3
- sub r2,r22,r2
- sub r3,r23,r3
- beq/u r22,r63,tr0
- ptabs r18,tr1
- blink tr0,r18
- sub r63,r2,r2
- blink tr1,r63
- ENDFUNC(GLOBAL(moddi3))
-#endif /* __SHMEDIA__ */
-#endif /* L_moddi3 */
-
#ifdef L_set_fpscr
#if !defined (__SH2A_NOFPU__)
-#if defined (__SH2E__) || defined (__SH2A__) || defined (__SH3E__) || defined(__SH4_SINGLE__) || defined(__SH4__) || defined(__SH4_SINGLE_ONLY__) || __SH5__ == 32
-#ifdef __SH5__
- .mode SHcompact
-#endif
+#if defined (__SH2E__) || defined (__SH2A__) || defined (__SH3E__) || defined(__SH4_SINGLE__) || defined(__SH4__) || defined(__SH4_SINGLE_ONLY__)
.global GLOBAL(set_fpscr)
HIDDEN_FUNC(GLOBAL(set_fpscr))
GLOBAL(set_fpscr):
@@ -2161,39 +1477,8 @@ LOCAL(set_fpscr_L1):
#endif /* __SH2A_NOFPU__ */
#endif /* L_set_fpscr */
#ifdef L_ic_invalidate
-#if __SH5__ == 32
- .mode SHmedia
- .section .text..SHmedia32,"ax"
- .align 2
- .global GLOBAL(init_trampoline)
- HIDDEN_FUNC(GLOBAL(init_trampoline))
-GLOBAL(init_trampoline):
- st.l r0,8,r2
-#ifdef __LITTLE_ENDIAN__
- movi 9,r20
- shori 0x402b,r20
- shori 0xd101,r20
- shori 0xd002,r20
-#else
- movi 0xffffffffffffd002,r20
- shori 0xd101,r20
- shori 0x402b,r20
- shori 9,r20
-#endif
- st.q r0,0,r20
- st.l r0,12,r3
- ENDFUNC(GLOBAL(init_trampoline))
- .global GLOBAL(ic_invalidate)
- HIDDEN_FUNC(GLOBAL(ic_invalidate))
-GLOBAL(ic_invalidate):
- ocbwb r0,0
- synco
- icbi r0, 0
- ptabs r18, tr0
- synci
- blink tr0, r63
- ENDFUNC(GLOBAL(ic_invalidate))
-#elif defined(__SH4A__)
+
+#if defined(__SH4A__)
.global GLOBAL(ic_invalidate)
HIDDEN_FUNC(GLOBAL(ic_invalidate))
GLOBAL(ic_invalidate):
@@ -2203,7 +1488,7 @@ GLOBAL(ic_invalidate):
rts
nop
ENDFUNC(GLOBAL(ic_invalidate))
-#elif defined(__SH4_SINGLE__) || defined(__SH4__) || defined(__SH4_SINGLE_ONLY__) || (defined(__SH4_NOFPU__) && !defined(__SH5__))
+#elif defined(__SH4_SINGLE__) || defined(__SH4__) || defined(__SH4_SINGLE_ONLY__) || defined(__SH4_NOFPU__)
/* For system code, we use ic_invalidate_line_i, but user code
needs a different mechanism. A kernel call is generally not
available, and it would also be slow. Different SH4 variants use
@@ -2259,7 +1544,7 @@ GLOBAL(ic_invalidate):
#endif /* L_ic_invalidate */
#ifdef L_ic_invalidate_array
-#if defined(__SH4A__) || (defined (__FORCE_SH4A__) && (defined(__SH4_SINGLE__) || defined(__SH4__) || defined(__SH4_SINGLE_ONLY__) || (defined(__SH4_NOFPU__) && !defined(__SH5__))))
+#if defined(__SH4A__) || (defined (__FORCE_SH4A__) && (defined(__SH4_SINGLE__) || defined(__SH4__) || defined(__SH4_SINGLE_ONLY__) || defined(__SH4_NOFPU__)))
.global GLOBAL(ic_invalidate_array)
/* This is needed when an SH4 dso with trampolines is used on SH4A. */
.global GLOBAL(ic_invalidate_array)
@@ -2273,7 +1558,7 @@ GLOBAL(ic_invalidate_array):
.align 2
.long 0
ENDFUNC(GLOBAL(ic_invalidate_array))
-#elif defined(__SH4_SINGLE__) || defined(__SH4__) || defined(__SH4_SINGLE_ONLY__) || (defined(__SH4_NOFPU__) && !defined(__SH5__))
+#elif defined(__SH4_SINGLE__) || defined(__SH4__) || defined(__SH4_SINGLE_ONLY__) || defined(__SH4_NOFPU__)
.global GLOBAL(ic_invalidate_array)
.p2align 5
FUNC(GLOBAL(ic_invalidate_array))
@@ -2329,1047 +1614,10 @@ GLOBAL(ic_invalidate_array):
#endif /* SH4 */
#endif /* L_ic_invalidate_array */
-#if defined (__SH5__) && __SH5__ == 32
-#ifdef L_shcompact_call_trampoline
- .section .rodata
- .align 1
-LOCAL(ct_main_table):
-.word LOCAL(ct_r2_fp) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r2_ld) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r2_pop) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r3_fp) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r3_ld) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r3_pop) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r4_fp) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r4_ld) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r4_pop) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r5_fp) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r5_ld) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r5_pop) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r6_fph) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r6_fpl) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r6_ld) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r6_pop) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r7_fph) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r7_fpl) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r7_ld) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r7_pop) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r8_fph) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r8_fpl) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r8_ld) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r8_pop) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r9_fph) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r9_fpl) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r9_ld) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r9_pop) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_pop_seq) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_pop_seq) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_r9_pop) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_ret_wide) - datalabel LOCAL(ct_main_label)
-.word LOCAL(ct_call_func) - datalabel LOCAL(ct_main_label)
- .mode SHmedia
- .section .text..SHmedia32, "ax"
- .align 2
-
- /* This function loads 64-bit general-purpose registers from the
- stack, from a memory address contained in them or from an FP
- register, according to a cookie passed in r1. Its execution
- time is linear on the number of registers that actually have
- to be copied. See sh.h for details on the actual bit pattern.
-
- The function to be called is passed in r0. If a 32-bit return
- value is expected, the actual function will be tail-called,
- otherwise the return address will be stored in r10 (that the
- caller should expect to be clobbered) and the return value
- will be expanded into r2/r3 upon return. */
-
- .global GLOBAL(GCC_shcompact_call_trampoline)
- FUNC(GLOBAL(GCC_shcompact_call_trampoline))
-GLOBAL(GCC_shcompact_call_trampoline):
- ptabs/l r0, tr0 /* Prepare to call the actual function. */
- movi ((datalabel LOCAL(ct_main_table) - 31 * 2) >> 16) & 65535, r0
- pt/l LOCAL(ct_loop), tr1
- addz.l r1, r63, r1
- shori ((datalabel LOCAL(ct_main_table) - 31 * 2)) & 65535, r0
-LOCAL(ct_loop):
- nsb r1, r28
- shlli r28, 1, r29
- ldx.w r0, r29, r30
-LOCAL(ct_main_label):
- ptrel/l r30, tr2
- blink tr2, r63
-LOCAL(ct_r2_fp): /* Copy r2 from an FP register. */
- /* It must be dr0, so just do it. */
- fmov.dq dr0, r2
- movi 7, r30
- shlli r30, 29, r31
- andc r1, r31, r1
- blink tr1, r63
-LOCAL(ct_r3_fp): /* Copy r3 from an FP register. */
- /* It is either dr0 or dr2. */
- movi 7, r30
- shlri r1, 26, r32
- shlli r30, 26, r31
- andc r1, r31, r1
- fmov.dq dr0, r3
- beqi/l r32, 4, tr1
- fmov.dq dr2, r3
- blink tr1, r63
-LOCAL(ct_r4_fp): /* Copy r4 from an FP register. */
- shlri r1, 23 - 3, r34
- andi r34, 3 << 3, r33
- addi r33, LOCAL(ct_r4_fp_copy) - datalabel LOCAL(ct_r4_fp_base), r32
-LOCAL(ct_r4_fp_base):
- ptrel/l r32, tr2
- movi 7, r30
- shlli r30, 23, r31
- andc r1, r31, r1
- blink tr2, r63
-LOCAL(ct_r4_fp_copy):
- fmov.dq dr0, r4
- blink tr1, r63
- fmov.dq dr2, r4
- blink tr1, r63
- fmov.dq dr4, r4
- blink tr1, r63
-LOCAL(ct_r5_fp): /* Copy r5 from an FP register. */
- shlri r1, 20 - 3, r34
- andi r34, 3 << 3, r33
- addi r33, LOCAL(ct_r5_fp_copy) - datalabel LOCAL(ct_r5_fp_base), r32
-LOCAL(ct_r5_fp_base):
- ptrel/l r32, tr2
- movi 7, r30
- shlli r30, 20, r31
- andc r1, r31, r1
- blink tr2, r63
-LOCAL(ct_r5_fp_copy):
- fmov.dq dr0, r5
- blink tr1, r63
- fmov.dq dr2, r5
- blink tr1, r63
- fmov.dq dr4, r5
- blink tr1, r63
- fmov.dq dr6, r5
- blink tr1, r63
-LOCAL(ct_r6_fph): /* Copy r6 from a high FP register. */
- /* It must be dr8. */
- fmov.dq dr8, r6
- movi 15, r30
- shlli r30, 16, r31
- andc r1, r31, r1
- blink tr1, r63
-LOCAL(ct_r6_fpl): /* Copy r6 from a low FP register. */
- shlri r1, 16 - 3, r34
- andi r34, 3 << 3, r33
- addi r33, LOCAL(ct_r6_fp_copy) - datalabel LOCAL(ct_r6_fp_base), r32
-LOCAL(ct_r6_fp_base):
- ptrel/l r32, tr2
- movi 7, r30
- shlli r30, 16, r31
- andc r1, r31, r1
- blink tr2, r63
-LOCAL(ct_r6_fp_copy):
- fmov.dq dr0, r6
- blink tr1, r63
- fmov.dq dr2, r6
- blink tr1, r63
- fmov.dq dr4, r6
- blink tr1, r63
- fmov.dq dr6, r6
- blink tr1, r63
-LOCAL(ct_r7_fph): /* Copy r7 from a high FP register. */
- /* It is either dr8 or dr10. */
- movi 15 << 12, r31
- shlri r1, 12, r32
- andc r1, r31, r1
- fmov.dq dr8, r7
- beqi/l r32, 8, tr1
- fmov.dq dr10, r7
- blink tr1, r63
-LOCAL(ct_r7_fpl): /* Copy r7 from a low FP register. */
- shlri r1, 12 - 3, r34
- andi r34, 3 << 3, r33
- addi r33, LOCAL(ct_r7_fp_copy) - datalabel LOCAL(ct_r7_fp_base), r32
-LOCAL(ct_r7_fp_base):
- ptrel/l r32, tr2
- movi 7 << 12, r31
- andc r1, r31, r1
- blink tr2, r63
-LOCAL(ct_r7_fp_copy):
- fmov.dq dr0, r7
- blink tr1, r63
- fmov.dq dr2, r7
- blink tr1, r63
- fmov.dq dr4, r7
- blink tr1, r63
- fmov.dq dr6, r7
- blink tr1, r63
-LOCAL(ct_r8_fph): /* Copy r8 from a high FP register. */
- /* It is either dr8 or dr10. */
- movi 15 << 8, r31
- andi r1, 1 << 8, r32
- andc r1, r31, r1
- fmov.dq dr8, r8
- beq/l r32, r63, tr1
- fmov.dq dr10, r8
- blink tr1, r63
-LOCAL(ct_r8_fpl): /* Copy r8 from a low FP register. */
- shlri r1, 8 - 3, r34
- andi r34, 3 << 3, r33
- addi r33, LOCAL(ct_r8_fp_copy) - datalabel LOCAL(ct_r8_fp_base), r32
-LOCAL(ct_r8_fp_base):
- ptrel/l r32, tr2
- movi 7 << 8, r31
- andc r1, r31, r1
- blink tr2, r63
-LOCAL(ct_r8_fp_copy):
- fmov.dq dr0, r8
- blink tr1, r63
- fmov.dq dr2, r8
- blink tr1, r63
- fmov.dq dr4, r8
- blink tr1, r63
- fmov.dq dr6, r8
- blink tr1, r63
-LOCAL(ct_r9_fph): /* Copy r9 from a high FP register. */
- /* It is either dr8 or dr10. */
- movi 15 << 4, r31
- andi r1, 1 << 4, r32
- andc r1, r31, r1
- fmov.dq dr8, r9
- beq/l r32, r63, tr1
- fmov.dq dr10, r9
- blink tr1, r63
-LOCAL(ct_r9_fpl): /* Copy r9 from a low FP register. */
- shlri r1, 4 - 3, r34
- andi r34, 3 << 3, r33
- addi r33, LOCAL(ct_r9_fp_copy) - datalabel LOCAL(ct_r9_fp_base), r32
-LOCAL(ct_r9_fp_base):
- ptrel/l r32, tr2
- movi 7 << 4, r31
- andc r1, r31, r1
- blink tr2, r63
-LOCAL(ct_r9_fp_copy):
- fmov.dq dr0, r9
- blink tr1, r63
- fmov.dq dr2, r9
- blink tr1, r63
- fmov.dq dr4, r9
- blink tr1, r63
- fmov.dq dr6, r9
- blink tr1, r63
-LOCAL(ct_r2_ld): /* Copy r2 from a memory address. */
- pt/l LOCAL(ct_r2_load), tr2
- movi 3, r30
- shlli r30, 29, r31
- and r1, r31, r32
- andc r1, r31, r1
- beq/l r31, r32, tr2
- addi.l r2, 8, r3
- ldx.q r2, r63, r2
- /* Fall through. */
-LOCAL(ct_r3_ld): /* Copy r3 from a memory address. */
- pt/l LOCAL(ct_r3_load), tr2
- movi 3, r30
- shlli r30, 26, r31
- and r1, r31, r32
- andc r1, r31, r1
- beq/l r31, r32, tr2
- addi.l r3, 8, r4
- ldx.q r3, r63, r3
-LOCAL(ct_r4_ld): /* Copy r4 from a memory address. */
- pt/l LOCAL(ct_r4_load), tr2
- movi 3, r30
- shlli r30, 23, r31
- and r1, r31, r32
- andc r1, r31, r1
- beq/l r31, r32, tr2
- addi.l r4, 8, r5
- ldx.q r4, r63, r4
-LOCAL(ct_r5_ld): /* Copy r5 from a memory address. */
- pt/l LOCAL(ct_r5_load), tr2
- movi 3, r30
- shlli r30, 20, r31
- and r1, r31, r32
- andc r1, r31, r1
- beq/l r31, r32, tr2
- addi.l r5, 8, r6
- ldx.q r5, r63, r5
-LOCAL(ct_r6_ld): /* Copy r6 from a memory address. */
- pt/l LOCAL(ct_r6_load), tr2
- movi 3 << 16, r31
- and r1, r31, r32
- andc r1, r31, r1
- beq/l r31, r32, tr2
- addi.l r6, 8, r7
- ldx.q r6, r63, r6
-LOCAL(ct_r7_ld): /* Copy r7 from a memory address. */
- pt/l LOCAL(ct_r7_load), tr2
- movi 3 << 12, r31
- and r1, r31, r32
- andc r1, r31, r1
- beq/l r31, r32, tr2
- addi.l r7, 8, r8
- ldx.q r7, r63, r7
-LOCAL(ct_r8_ld): /* Copy r8 from a memory address. */
- pt/l LOCAL(ct_r8_load), tr2
- movi 3 << 8, r31
- and r1, r31, r32
- andc r1, r31, r1
- beq/l r31, r32, tr2
- addi.l r8, 8, r9
- ldx.q r8, r63, r8
-LOCAL(ct_r9_ld): /* Copy r9 from a memory address. */
- pt/l LOCAL(ct_check_tramp), tr2
- ldx.q r9, r63, r9
- blink tr2, r63
-LOCAL(ct_r2_load):
- ldx.q r2, r63, r2
- blink tr1, r63
-LOCAL(ct_r3_load):
- ldx.q r3, r63, r3
- blink tr1, r63
-LOCAL(ct_r4_load):
- ldx.q r4, r63, r4
- blink tr1, r63
-LOCAL(ct_r5_load):
- ldx.q r5, r63, r5
- blink tr1, r63
-LOCAL(ct_r6_load):
- ldx.q r6, r63, r6
- blink tr1, r63
-LOCAL(ct_r7_load):
- ldx.q r7, r63, r7
- blink tr1, r63
-LOCAL(ct_r8_load):
- ldx.q r8, r63, r8
- blink tr1, r63
-LOCAL(ct_r2_pop): /* Pop r2 from the stack. */
- movi 1, r30
- ldx.q r15, r63, r2
- shlli r30, 29, r31
- addi.l r15, 8, r15
- andc r1, r31, r1
- blink tr1, r63
-LOCAL(ct_r3_pop): /* Pop r3 from the stack. */
- movi 1, r30
- ldx.q r15, r63, r3
- shlli r30, 26, r31
- addi.l r15, 8, r15
- andc r1, r31, r1
- blink tr1, r63
-LOCAL(ct_r4_pop): /* Pop r4 from the stack. */
- movi 1, r30
- ldx.q r15, r63, r4
- shlli r30, 23, r31
- addi.l r15, 8, r15
- andc r1, r31, r1
- blink tr1, r63
-LOCAL(ct_r5_pop): /* Pop r5 from the stack. */
- movi 1, r30
- ldx.q r15, r63, r5
- shlli r30, 20, r31
- addi.l r15, 8, r15
- andc r1, r31, r1
- blink tr1, r63
-LOCAL(ct_r6_pop): /* Pop r6 from the stack. */
- movi 1, r30
- ldx.q r15, r63, r6
- shlli r30, 16, r31
- addi.l r15, 8, r15
- andc r1, r31, r1
- blink tr1, r63
-LOCAL(ct_r7_pop): /* Pop r7 from the stack. */
- ldx.q r15, r63, r7
- movi 1 << 12, r31
- addi.l r15, 8, r15
- andc r1, r31, r1
- blink tr1, r63
-LOCAL(ct_r8_pop): /* Pop r8 from the stack. */
- ldx.q r15, r63, r8
- movi 1 << 8, r31
- addi.l r15, 8, r15
- andc r1, r31, r1
- blink tr1, r63
-LOCAL(ct_pop_seq): /* Pop a sequence of registers off the stack. */
- andi r1, 7 << 1, r30
- movi (LOCAL(ct_end_of_pop_seq) >> 16) & 65535, r32
- shlli r30, 2, r31
- shori LOCAL(ct_end_of_pop_seq) & 65535, r32
- sub.l r32, r31, r33
- ptabs/l r33, tr2
- blink tr2, r63
-LOCAL(ct_start_of_pop_seq): /* Beginning of pop sequence. */
- ldx.q r15, r63, r3
- addi.l r15, 8, r15
- ldx.q r15, r63, r4
- addi.l r15, 8, r15
- ldx.q r15, r63, r5
- addi.l r15, 8, r15
- ldx.q r15, r63, r6
- addi.l r15, 8, r15
- ldx.q r15, r63, r7
- addi.l r15, 8, r15
- ldx.q r15, r63, r8
- addi.l r15, 8, r15
-LOCAL(ct_r9_pop): /* Pop r9 from the stack. */
- ldx.q r15, r63, r9
- addi.l r15, 8, r15
-LOCAL(ct_end_of_pop_seq): /* Label used to compute first pop instruction. */
-LOCAL(ct_check_tramp): /* Check whether we need a trampoline. */
- pt/u LOCAL(ct_ret_wide), tr2
- andi r1, 1, r1
- bne/u r1, r63, tr2
-LOCAL(ct_call_func): /* Just branch to the function. */
- blink tr0, r63
-LOCAL(ct_ret_wide): /* Call the function, so that we can unpack its
- 64-bit return value. */
- add.l r18, r63, r10
- blink tr0, r18
- ptabs r10, tr0
-#if __LITTLE_ENDIAN__
- shari r2, 32, r3
- add.l r2, r63, r2
-#else
- add.l r2, r63, r3
- shari r2, 32, r2
-#endif
- blink tr0, r63
-
- ENDFUNC(GLOBAL(GCC_shcompact_call_trampoline))
-#endif /* L_shcompact_call_trampoline */
-
-#ifdef L_shcompact_return_trampoline
- /* This function does the converse of the code in `ret_wide'
- above. It is tail-called by SHcompact functions returning
- 64-bit non-floating-point values, to pack the 32-bit values in
- r2 and r3 into r2. */
-
- .mode SHmedia
- .section .text..SHmedia32, "ax"
- .align 2
- .global GLOBAL(GCC_shcompact_return_trampoline)
- HIDDEN_FUNC(GLOBAL(GCC_shcompact_return_trampoline))
-GLOBAL(GCC_shcompact_return_trampoline):
- ptabs/l r18, tr0
-#if __LITTLE_ENDIAN__
- addz.l r2, r63, r2
- shlli r3, 32, r3
-#else
- addz.l r3, r63, r3
- shlli r2, 32, r2
-#endif
- or r3, r2, r2
- blink tr0, r63
-
- ENDFUNC(GLOBAL(GCC_shcompact_return_trampoline))
-#endif /* L_shcompact_return_trampoline */
-
-#ifdef L_shcompact_incoming_args
- .section .rodata
- .align 1
-LOCAL(ia_main_table):
-.word 1 /* Invalid, just loop */
-.word LOCAL(ia_r2_ld) - datalabel LOCAL(ia_main_label)
-.word LOCAL(ia_r2_push) - datalabel LOCAL(ia_main_label)
-.word 1 /* Invalid, just loop */
-.word LOCAL(ia_r3_ld) - datalabel LOCAL(ia_main_label)
-.word LOCAL(ia_r3_push) - datalabel LOCAL(ia_main_label)
-.word 1 /* Invalid, just loop */
-.word LOCAL(ia_r4_ld) - datalabel LOCAL(ia_main_label)
-.word LOCAL(ia_r4_push) - datalabel LOCAL(ia_main_label)
-.word 1 /* Invalid, just loop */
-.word LOCAL(ia_r5_ld) - datalabel LOCAL(ia_main_label)
-.word LOCAL(ia_r5_push) - datalabel LOCAL(ia_main_label)
-.word 1 /* Invalid, just loop */
-.word 1 /* Invalid, just loop */
-.word LOCAL(ia_r6_ld) - datalabel LOCAL(ia_main_label)
-.word LOCAL(ia_r6_push) - datalabel LOCAL(ia_main_label)
-.word 1 /* Invalid, just loop */
-.word 1 /* Invalid, just loop */
-.word LOCAL(ia_r7_ld) - datalabel LOCAL(ia_main_label)
-.word LOCAL(ia_r7_push) - datalabel LOCAL(ia_main_label)
-.word 1 /* Invalid, just loop */
-.word 1 /* Invalid, just loop */
-.word LOCAL(ia_r8_ld) - datalabel LOCAL(ia_main_label)
-.word LOCAL(ia_r8_push) - datalabel LOCAL(ia_main_label)
-.word 1 /* Invalid, just loop */
-.word 1 /* Invalid, just loop */
-.word LOCAL(ia_r9_ld) - datalabel LOCAL(ia_main_label)
-.word LOCAL(ia_r9_push) - datalabel LOCAL(ia_main_label)
-.word LOCAL(ia_push_seq) - datalabel LOCAL(ia_main_label)
-.word LOCAL(ia_push_seq) - datalabel LOCAL(ia_main_label)
-.word LOCAL(ia_r9_push) - datalabel LOCAL(ia_main_label)
-.word LOCAL(ia_return) - datalabel LOCAL(ia_main_label)
-.word LOCAL(ia_return) - datalabel LOCAL(ia_main_label)
- .mode SHmedia
- .section .text..SHmedia32, "ax"
- .align 2
-
- /* This function stores 64-bit general-purpose registers back in
- the stack, and loads the address in which each register
- was stored into itself. The lower 32 bits of r17 hold the address
- to begin storing, and the upper 32 bits of r17 hold the cookie.
- Its execution time is linear on the
- number of registers that actually have to be copied, and it is
- optimized for structures larger than 64 bits, as opposed to
- individual `long long' arguments. See sh.h for details on the
- actual bit pattern. */
-
- .global GLOBAL(GCC_shcompact_incoming_args)
- FUNC(GLOBAL(GCC_shcompact_incoming_args))
-GLOBAL(GCC_shcompact_incoming_args):
- ptabs/l r18, tr0 /* Prepare to return. */
- shlri r17, 32, r0 /* Load the cookie. */
- movi ((datalabel LOCAL(ia_main_table) - 31 * 2) >> 16) & 65535, r43
- pt/l LOCAL(ia_loop), tr1
- add.l r17, r63, r17
- shori ((datalabel LOCAL(ia_main_table) - 31 * 2)) & 65535, r43
-LOCAL(ia_loop):
- nsb r0, r36
- shlli r36, 1, r37
- ldx.w r43, r37, r38
-LOCAL(ia_main_label):
- ptrel/l r38, tr2
- blink tr2, r63
-LOCAL(ia_r2_ld): /* Store r2 and load its address. */
- movi 3, r38
- shlli r38, 29, r39
- and r0, r39, r40
- andc r0, r39, r0
- stx.q r17, r63, r2
- add.l r17, r63, r2
- addi.l r17, 8, r17
- beq/u r39, r40, tr1
-LOCAL(ia_r3_ld): /* Store r3 and load its address. */
- movi 3, r38
- shlli r38, 26, r39
- and r0, r39, r40
- andc r0, r39, r0
- stx.q r17, r63, r3
- add.l r17, r63, r3
- addi.l r17, 8, r17
- beq/u r39, r40, tr1
-LOCAL(ia_r4_ld): /* Store r4 and load its address. */
- movi 3, r38
- shlli r38, 23, r39
- and r0, r39, r40
- andc r0, r39, r0
- stx.q r17, r63, r4
- add.l r17, r63, r4
- addi.l r17, 8, r17
- beq/u r39, r40, tr1
-LOCAL(ia_r5_ld): /* Store r5 and load its address. */
- movi 3, r38
- shlli r38, 20, r39
- and r0, r39, r40
- andc r0, r39, r0
- stx.q r17, r63, r5
- add.l r17, r63, r5
- addi.l r17, 8, r17
- beq/u r39, r40, tr1
-LOCAL(ia_r6_ld): /* Store r6 and load its address. */
- movi 3, r38
- shlli r38, 16, r39
- and r0, r39, r40
- andc r0, r39, r0
- stx.q r17, r63, r6
- add.l r17, r63, r6
- addi.l r17, 8, r17
- beq/u r39, r40, tr1
-LOCAL(ia_r7_ld): /* Store r7 and load its address. */
- movi 3 << 12, r39
- and r0, r39, r40
- andc r0, r39, r0
- stx.q r17, r63, r7
- add.l r17, r63, r7
- addi.l r17, 8, r17
- beq/u r39, r40, tr1
-LOCAL(ia_r8_ld): /* Store r8 and load its address. */
- movi 3 << 8, r39
- and r0, r39, r40
- andc r0, r39, r0
- stx.q r17, r63, r8
- add.l r17, r63, r8
- addi.l r17, 8, r17
- beq/u r39, r40, tr1
-LOCAL(ia_r9_ld): /* Store r9 and load its address. */
- stx.q r17, r63, r9
- add.l r17, r63, r9
- blink tr0, r63
-LOCAL(ia_r2_push): /* Push r2 onto the stack. */
- movi 1, r38
- shlli r38, 29, r39
- andc r0, r39, r0
- stx.q r17, r63, r2
- addi.l r17, 8, r17
- blink tr1, r63
-LOCAL(ia_r3_push): /* Push r3 onto the stack. */
- movi 1, r38
- shlli r38, 26, r39
- andc r0, r39, r0
- stx.q r17, r63, r3
- addi.l r17, 8, r17
- blink tr1, r63
-LOCAL(ia_r4_push): /* Push r4 onto the stack. */
- movi 1, r38
- shlli r38, 23, r39
- andc r0, r39, r0
- stx.q r17, r63, r4
- addi.l r17, 8, r17
- blink tr1, r63
-LOCAL(ia_r5_push): /* Push r5 onto the stack. */
- movi 1, r38
- shlli r38, 20, r39
- andc r0, r39, r0
- stx.q r17, r63, r5
- addi.l r17, 8, r17
- blink tr1, r63
-LOCAL(ia_r6_push): /* Push r6 onto the stack. */
- movi 1, r38
- shlli r38, 16, r39
- andc r0, r39, r0
- stx.q r17, r63, r6
- addi.l r17, 8, r17
- blink tr1, r63
-LOCAL(ia_r7_push): /* Push r7 onto the stack. */
- movi 1 << 12, r39
- andc r0, r39, r0
- stx.q r17, r63, r7
- addi.l r17, 8, r17
- blink tr1, r63
-LOCAL(ia_r8_push): /* Push r8 onto the stack. */
- movi 1 << 8, r39
- andc r0, r39, r0
- stx.q r17, r63, r8
- addi.l r17, 8, r17
- blink tr1, r63
-LOCAL(ia_push_seq): /* Push a sequence of registers onto the stack. */
- andi r0, 7 << 1, r38
- movi (LOCAL(ia_end_of_push_seq) >> 16) & 65535, r40
- shlli r38, 2, r39
- shori LOCAL(ia_end_of_push_seq) & 65535, r40
- sub.l r40, r39, r41
- ptabs/l r41, tr2
- blink tr2, r63
-LOCAL(ia_stack_of_push_seq): /* Beginning of push sequence. */
- stx.q r17, r63, r3
- addi.l r17, 8, r17
- stx.q r17, r63, r4
- addi.l r17, 8, r17
- stx.q r17, r63, r5
- addi.l r17, 8, r17
- stx.q r17, r63, r6
- addi.l r17, 8, r17
- stx.q r17, r63, r7
- addi.l r17, 8, r17
- stx.q r17, r63, r8
- addi.l r17, 8, r17
-LOCAL(ia_r9_push): /* Push r9 onto the stack. */
- stx.q r17, r63, r9
-LOCAL(ia_return): /* Return. */
- blink tr0, r63
-LOCAL(ia_end_of_push_seq): /* Label used to compute the first push instruction. */
- ENDFUNC(GLOBAL(GCC_shcompact_incoming_args))
-#endif /* L_shcompact_incoming_args */
-#endif
-#if __SH5__
-#ifdef L_nested_trampoline
-#if __SH5__ == 32
- .section .text..SHmedia32,"ax"
-#else
- .text
-#endif
- .align 3 /* It is copied in units of 8 bytes in SHmedia mode. */
- .global GLOBAL(GCC_nested_trampoline)
- HIDDEN_FUNC(GLOBAL(GCC_nested_trampoline))
-GLOBAL(GCC_nested_trampoline):
- .mode SHmedia
- ptrel/u r63, tr0
- gettr tr0, r0
-#if __SH5__ == 64
- ld.q r0, 24, r1
-#else
- ld.l r0, 24, r1
-#endif
- ptabs/l r1, tr1
-#if __SH5__ == 64
- ld.q r0, 32, r1
-#else
- ld.l r0, 28, r1
-#endif
- blink tr1, r63
-
- ENDFUNC(GLOBAL(GCC_nested_trampoline))
-#endif /* L_nested_trampoline */
-#endif /* __SH5__ */
-#if __SH5__ == 32
-#ifdef L_push_pop_shmedia_regs
- .section .text..SHmedia32,"ax"
- .mode SHmedia
- .align 2
-#ifndef __SH4_NOFPU__
- .global GLOBAL(GCC_push_shmedia_regs)
- FUNC(GLOBAL(GCC_push_shmedia_regs))
-GLOBAL(GCC_push_shmedia_regs):
- addi.l r15, -14*8, r15
- fst.d r15, 13*8, dr62
- fst.d r15, 12*8, dr60
- fst.d r15, 11*8, dr58
- fst.d r15, 10*8, dr56
- fst.d r15, 9*8, dr54
- fst.d r15, 8*8, dr52
- fst.d r15, 7*8, dr50
- fst.d r15, 6*8, dr48
- fst.d r15, 5*8, dr46
- fst.d r15, 4*8, dr44
- fst.d r15, 3*8, dr42
- fst.d r15, 2*8, dr40
- fst.d r15, 1*8, dr38
- fst.d r15, 0*8, dr36
-#else /* ! __SH4_NOFPU__ */
- .global GLOBAL(GCC_push_shmedia_regs_nofpu)
- FUNC(GLOBAL(GCC_push_shmedia_regs_nofpu))
-GLOBAL(GCC_push_shmedia_regs_nofpu):
-#endif /* ! __SH4_NOFPU__ */
- ptabs/l r18, tr0
- addi.l r15, -27*8, r15
- gettr tr7, r62
- gettr tr6, r61
- gettr tr5, r60
- st.q r15, 26*8, r62
- st.q r15, 25*8, r61
- st.q r15, 24*8, r60
- st.q r15, 23*8, r59
- st.q r15, 22*8, r58
- st.q r15, 21*8, r57
- st.q r15, 20*8, r56
- st.q r15, 19*8, r55
- st.q r15, 18*8, r54
- st.q r15, 17*8, r53
- st.q r15, 16*8, r52
- st.q r15, 15*8, r51
- st.q r15, 14*8, r50
- st.q r15, 13*8, r49
- st.q r15, 12*8, r48
- st.q r15, 11*8, r47
- st.q r15, 10*8, r46
- st.q r15, 9*8, r45
- st.q r15, 8*8, r44
- st.q r15, 7*8, r35
- st.q r15, 6*8, r34
- st.q r15, 5*8, r33
- st.q r15, 4*8, r32
- st.q r15, 3*8, r31
- st.q r15, 2*8, r30
- st.q r15, 1*8, r29
- st.q r15, 0*8, r28
- blink tr0, r63
-#ifndef __SH4_NOFPU__
- ENDFUNC(GLOBAL(GCC_push_shmedia_regs))
-#else
- ENDFUNC(GLOBAL(GCC_push_shmedia_regs_nofpu))
-#endif
-#ifndef __SH4_NOFPU__
- .global GLOBAL(GCC_pop_shmedia_regs)
- FUNC(GLOBAL(GCC_pop_shmedia_regs))
-GLOBAL(GCC_pop_shmedia_regs):
- pt .L0, tr1
- movi 41*8, r0
- fld.d r15, 40*8, dr62
- fld.d r15, 39*8, dr60
- fld.d r15, 38*8, dr58
- fld.d r15, 37*8, dr56
- fld.d r15, 36*8, dr54
- fld.d r15, 35*8, dr52
- fld.d r15, 34*8, dr50
- fld.d r15, 33*8, dr48
- fld.d r15, 32*8, dr46
- fld.d r15, 31*8, dr44
- fld.d r15, 30*8, dr42
- fld.d r15, 29*8, dr40
- fld.d r15, 28*8, dr38
- fld.d r15, 27*8, dr36
- blink tr1, r63
-#else /* ! __SH4_NOFPU__ */
- .global GLOBAL(GCC_pop_shmedia_regs_nofpu)
- FUNC(GLOBAL(GCC_pop_shmedia_regs_nofpu))
-GLOBAL(GCC_pop_shmedia_regs_nofpu):
-#endif /* ! __SH4_NOFPU__ */
- movi 27*8, r0
-.L0:
- ptabs r18, tr0
- ld.q r15, 26*8, r62
- ld.q r15, 25*8, r61
- ld.q r15, 24*8, r60
- ptabs r62, tr7
- ptabs r61, tr6
- ptabs r60, tr5
- ld.q r15, 23*8, r59
- ld.q r15, 22*8, r58
- ld.q r15, 21*8, r57
- ld.q r15, 20*8, r56
- ld.q r15, 19*8, r55
- ld.q r15, 18*8, r54
- ld.q r15, 17*8, r53
- ld.q r15, 16*8, r52
- ld.q r15, 15*8, r51
- ld.q r15, 14*8, r50
- ld.q r15, 13*8, r49
- ld.q r15, 12*8, r48
- ld.q r15, 11*8, r47
- ld.q r15, 10*8, r46
- ld.q r15, 9*8, r45
- ld.q r15, 8*8, r44
- ld.q r15, 7*8, r35
- ld.q r15, 6*8, r34
- ld.q r15, 5*8, r33
- ld.q r15, 4*8, r32
- ld.q r15, 3*8, r31
- ld.q r15, 2*8, r30
- ld.q r15, 1*8, r29
- ld.q r15, 0*8, r28
- add.l r15, r0, r15
- blink tr0, r63
-
-#ifndef __SH4_NOFPU__
- ENDFUNC(GLOBAL(GCC_pop_shmedia_regs))
-#else
- ENDFUNC(GLOBAL(GCC_pop_shmedia_regs_nofpu))
-#endif
-#endif /* __SH5__ == 32 */
-#endif /* L_push_pop_shmedia_regs */
#ifdef L_div_table
-#if __SH5__
-#if defined(__pic__) && __SHMEDIA__
- .global GLOBAL(sdivsi3)
- FUNC(GLOBAL(sdivsi3))
-#if __SH5__ == 32
- .section .text..SHmedia32,"ax"
-#else
- .text
-#endif
-#if 0
-/* ??? FIXME: Presumably due to a linker bug, exporting data symbols
- in a text section does not work (at least for shared libraries):
- the linker sets the LSB of the address as if this was SHmedia code. */
-#define TEXT_DATA_BUG
-#endif
- .align 2
- // inputs: r4,r5
- // clobbered: r1,r18,r19,r20,r21,r25,tr0
- // result in r0
- .global GLOBAL(sdivsi3)
-GLOBAL(sdivsi3):
-#ifdef TEXT_DATA_BUG
- ptb datalabel Local_div_table,tr0
-#else
- ptb GLOBAL(div_table_internal),tr0
-#endif
- nsb r5, r1
- shlld r5, r1, r25 // normalize; [-2 ..1, 1..2) in s2.62
- shari r25, 58, r21 // extract 5(6) bit index (s2.4 with hole -1..1)
- /* bubble */
- gettr tr0,r20
- ldx.ub r20, r21, r19 // u0.8
- shari r25, 32, r25 // normalize to s2.30
- shlli r21, 1, r21
- muls.l r25, r19, r19 // s2.38
- ldx.w r20, r21, r21 // s2.14
- ptabs r18, tr0
- shari r19, 24, r19 // truncate to s2.14
- sub r21, r19, r19 // some 11 bit inverse in s1.14
- muls.l r19, r19, r21 // u0.28
- sub r63, r1, r1
- addi r1, 92, r1
- muls.l r25, r21, r18 // s2.58
- shlli r19, 45, r19 // multiply by two and convert to s2.58
- /* bubble */
- sub r19, r18, r18
- shari r18, 28, r18 // some 22 bit inverse in s1.30
- muls.l r18, r25, r0 // s2.60
- muls.l r18, r4, r25 // s32.30
- /* bubble */
- shari r0, 16, r19 // s-16.44
- muls.l r19, r18, r19 // s-16.74
- shari r25, 63, r0
- shari r4, 14, r18 // s19.-14
- shari r19, 30, r19 // s-16.44
- muls.l r19, r18, r19 // s15.30
- xor r21, r0, r21 // You could also use the constant 1 << 27.
- add r21, r25, r21
- sub r21, r19, r21
- shard r21, r1, r21
- sub r21, r0, r0
- blink tr0, r63
- ENDFUNC(GLOBAL(sdivsi3))
-/* This table has been generated by divtab.c .
-Defects for bias -330:
- Max defect: 6.081536e-07 at -1.000000e+00
- Min defect: 2.849516e-08 at 1.030651e+00
- Max 2nd step defect: 9.606539e-12 at -1.000000e+00
- Min 2nd step defect: 0.000000e+00 at 0.000000e+00
- Defect at 1: 1.238659e-07
- Defect at -2: 1.061708e-07 */
-#else /* ! __pic__ || ! __SHMEDIA__ */
- .section .rodata
-#endif /* __pic__ */
-#if defined(TEXT_DATA_BUG) && defined(__pic__) && __SHMEDIA__
- .balign 2
- .type Local_div_table,@object
- .size Local_div_table,128
-/* negative division constants */
- .word -16638
- .word -17135
- .word -17737
- .word -18433
- .word -19103
- .word -19751
- .word -20583
- .word -21383
- .word -22343
- .word -23353
- .word -24407
- .word -25582
- .word -26863
- .word -28382
- .word -29965
- .word -31800
-/* negative division factors */
- .byte 66
- .byte 70
- .byte 75
- .byte 81
- .byte 87
- .byte 93
- .byte 101
- .byte 109
- .byte 119
- .byte 130
- .byte 142
- .byte 156
- .byte 172
- .byte 192
- .byte 214
- .byte 241
- .skip 16
-Local_div_table:
- .skip 16
-/* positive division factors */
- .byte 241
- .byte 214
- .byte 192
- .byte 172
- .byte 156
- .byte 142
- .byte 130
- .byte 119
- .byte 109
- .byte 101
- .byte 93
- .byte 87
- .byte 81
- .byte 75
- .byte 70
- .byte 66
-/* positive division constants */
- .word 31801
- .word 29966
- .word 28383
- .word 26864
- .word 25583
- .word 24408
- .word 23354
- .word 22344
- .word 21384
- .word 20584
- .word 19752
- .word 19104
- .word 18434
- .word 17738
- .word 17136
- .word 16639
- .section .rodata
-#endif /* TEXT_DATA_BUG */
- .balign 2
- .type GLOBAL(div_table),@object
- .size GLOBAL(div_table),128
-/* negative division constants */
- .word -16638
- .word -17135
- .word -17737
- .word -18433
- .word -19103
- .word -19751
- .word -20583
- .word -21383
- .word -22343
- .word -23353
- .word -24407
- .word -25582
- .word -26863
- .word -28382
- .word -29965
- .word -31800
-/* negative division factors */
- .byte 66
- .byte 70
- .byte 75
- .byte 81
- .byte 87
- .byte 93
- .byte 101
- .byte 109
- .byte 119
- .byte 130
- .byte 142
- .byte 156
- .byte 172
- .byte 192
- .byte 214
- .byte 241
- .skip 16
- .global GLOBAL(div_table)
-GLOBAL(div_table):
- HIDDEN_ALIAS(div_table_internal,div_table)
- .skip 16
-/* positive division factors */
- .byte 241
- .byte 214
- .byte 192
- .byte 172
- .byte 156
- .byte 142
- .byte 130
- .byte 119
- .byte 109
- .byte 101
- .byte 93
- .byte 87
- .byte 81
- .byte 75
- .byte 70
- .byte 66
-/* positive division constants */
- .word 31801
- .word 29966
- .word 28383
- .word 26864
- .word 25583
- .word 24408
- .word 23354
- .word 22344
- .word 21384
- .word 20584
- .word 19752
- .word 19104
- .word 18434
- .word 17738
- .word 17136
- .word 16639
-
-#elif defined (__SH2A__) || defined (__SH3__) || defined (__SH3E__) || defined (__SH4__) || defined (__SH4_SINGLE__) || defined (__SH4_SINGLE_ONLY__) || defined (__SH4_NOFPU__)
+
+#if defined (__SH2A__) || defined (__SH3__) || defined (__SH3E__) || defined (__SH4__) || defined (__SH4_SINGLE__) || defined (__SH4_SINGLE_ONLY__) || defined (__SH4_NOFPU__)
/* This code uses shld, thus is not suitable for SH1 / SH2. */
/* Signed / unsigned division without use of FPU, optimized for SH4.
@@ -3999,7 +2247,6 @@ LOCAL(div_table_inv):
#endif /* L_div_table */
#ifdef L_udiv_qrnnd_16
-#if !__SHMEDIA__
HIDDEN_FUNC(GLOBAL(udiv_qrnnd_16))
/* r0: rn r1: qn */ /* r0: n1 r4: n0 r5: d r6: d1 */ /* r2: __m */
/* n1 < d, but n1 might be larger than d1. */
@@ -4043,5 +2290,4 @@ GLOBAL(udiv_qrnnd_16):
0: rts
nop
ENDFUNC(GLOBAL(udiv_qrnnd_16))
-#endif /* !__SHMEDIA__ */
#endif /* L_udiv_qrnnd_16 */
diff --git a/libgcc/config/sh/linux-unwind.h b/libgcc/config/sh/linux-unwind.h
index e389cac..65005be 100644
--- a/libgcc/config/sh/linux-unwind.h
+++ b/libgcc/config/sh/linux-unwind.h
@@ -33,14 +33,6 @@ see the files COPYING3 and COPYING.RUNTIME respectively. If not, see
#include <sys/ucontext.h>
#include "insn-constants.h"
-# if defined (__SH5__)
-#define SH_DWARF_FRAME_GP0 0
-#define SH_DWARF_FRAME_FP0 77
-#define SH_DWARF_FRAME_BT0 68
-#define SH_DWARF_FRAME_PR_MEDIA 18
-#define SH_DWARF_FRAME_SR 65
-#define SH_DWARF_FRAME_FPSCR 76
-#else
#define SH_DWARF_FRAME_GP0 0
#define SH_DWARF_FRAME_FP0 25
#define SH_DWARF_FRAME_XD0 87
@@ -52,96 +44,6 @@ see the files COPYING3 and COPYING.RUNTIME respectively. If not, see
#define SH_DWARF_FRAME_SR 22
#define SH_DWARF_FRAME_FPUL 23
#define SH_DWARF_FRAME_FPSCR 24
-#endif /* defined (__SH5__) */
-
-#if defined (__SH5__)
-
-#define MD_FALLBACK_FRAME_STATE_FOR shmedia_fallback_frame_state
-
-static _Unwind_Reason_Code
-shmedia_fallback_frame_state (struct _Unwind_Context *context,
- _Unwind_FrameState *fs)
-{
- unsigned char *pc = context->ra;
- struct sigcontext *sc;
- long new_cfa;
- int i, r;
-
- /* movi 0x10,r9; shori 0x77,r9; trapa r9; nop (sigreturn) */
- /* movi 0x10,r9; shori 0xad,r9; trapa r9; nop (rt_sigreturn) */
- if ((*(unsigned long *) (pc-1) == 0xcc004090)
- && (*(unsigned long *) (pc+3) == 0xc801dc90)
- && (*(unsigned long *) (pc+7) == 0x6c91fff0)
- && (*(unsigned long *) (pc+11) == 0x6ff0fff0))
- sc = context->cfa;
- else if ((*(unsigned long *) (pc-1) == 0xcc004090)
- && (*(unsigned long *) (pc+3) == 0xc802b490)
- && (*(unsigned long *) (pc+7) == 0x6c91fff0)
- && (*(unsigned long *) (pc+11) == 0x6ff0fff0))
- {
- struct rt_sigframe {
- siginfo_t *pinfo;
- void *puc;
- siginfo_t info;
- struct ucontext uc;
- } *rt_ = context->cfa;
- /* The void * cast is necessary to avoid an aliasing warning.
- The aliasing warning is correct, but should not be a problem
- because it does not alias anything. */
- sc = (struct sigcontext *) (void *) &rt_->uc.uc_mcontext;
- }
- else
- return _URC_END_OF_STACK;
-
- new_cfa = sc->sc_regs[15];
- fs->regs.cfa_how = CFA_REG_OFFSET;
- fs->regs.cfa_reg = 15;
- fs->regs.cfa_offset = new_cfa - (long) context->cfa;
-
- for (i = 0; i < 63; i++)
- {
- if (i == 15)
- continue;
-
- fs->regs.reg[i].how = REG_SAVED_OFFSET;
- fs->regs.reg[i].loc.offset
- = (long)&(sc->sc_regs[i]) - new_cfa;
- }
-
- fs->regs.reg[SH_DWARF_FRAME_SR].how = REG_SAVED_OFFSET;
- fs->regs.reg[SH_DWARF_FRAME_SR].loc.offset
- = (long)&(sc->sc_sr) - new_cfa;
-
- r = SH_DWARF_FRAME_BT0;
- for (i = 0; i < 8; i++)
- {
- fs->regs.reg[r+i].how = REG_SAVED_OFFSET;
- fs->regs.reg[r+i].loc.offset
- = (long)&(sc->sc_tregs[i]) - new_cfa;
- }
-
- r = SH_DWARF_FRAME_FP0;
- for (i = 0; i < 32; i++)
- {
- fs->regs.reg[r+i].how = REG_SAVED_OFFSET;
- fs->regs.reg[r+i].loc.offset
- = (long)&(sc->sc_fpregs[i]) - new_cfa;
- }
-
- fs->regs.reg[SH_DWARF_FRAME_FPSCR].how = REG_SAVED_OFFSET;
- fs->regs.reg[SH_DWARF_FRAME_FPSCR].loc.offset
- = (long)&(sc->sc_fpscr) - new_cfa;
-
- /* We use the slot for the zero register to save return address. */
- fs->regs.reg[63].how = REG_SAVED_OFFSET;
- fs->regs.reg[63].loc.offset
- = (long)&(sc->sc_pc) - new_cfa;
- fs->retaddr_column = 63;
- fs->signal_frame = 1;
- return _URC_NO_REASON;
-}
-
-#else /* defined (__SH5__) */
#define MD_FALLBACK_FRAME_STATE_FOR sh_fallback_frame_state
@@ -250,6 +152,5 @@ sh_fallback_frame_state (struct _Unwind_Context *context,
fs->signal_frame = 1;
return _URC_NO_REASON;
}
-#endif /* defined (__SH5__) */
#endif /* inhibit_libc */
diff --git a/libgcc/config/sh/t-sh64 b/libgcc/config/sh/t-sh64
deleted file mode 100644
index fa9950e..0000000
--- a/libgcc/config/sh/t-sh64
+++ /dev/null
@@ -1,6 +0,0 @@
-LIB1ASMFUNCS = \
- _sdivsi3 _sdivsi3_i4 _udivsi3 _udivsi3_i4 _set_fpscr \
- _shcompact_call_trampoline _shcompact_return_trampoline \
- _shcompact_incoming_args _ic_invalidate _nested_trampoline \
- _push_pop_shmedia_regs \
- _udivdi3 _divdi3 _umoddi3 _moddi3 _div_table
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [SH][committed] Remove SH5 support in compiler
2016-04-29 14:11 ` Oleg Endo
@ 2016-04-30 1:58 ` Oleg Endo
2016-04-30 5:44 ` Oleg Endo
0 siblings, 1 reply; 10+ messages in thread
From: Oleg Endo @ 2016-04-30 1:58 UTC (permalink / raw)
To: gcc-patches
[-- Attachment #1: Type: text/plain, Size: 4220 bytes --]
On Fri, 2016-04-29 at 23:11 +0900, Oleg Endo wrote:
> On Fri, 2016-04-29 at 19:45 +0900, Oleg Endo wrote:
> > On Thu, 2016-04-28 at 10:27 +0900, Oleg Endo wrote:
> >
> > > The removal of SH5 support from GCC has been announced here
> > > https://gcc.gnu.org/ml/gcc/2015-08/msg00101.html
> > >
> > > The attached patch removes support for SH5 in the compiler back
> > > end.
> > > There are still some leftovers and new simplification
> > > opportunities.
> > > These will be addressed in later follow up patches.
> > >
> > > Tested on sh-elf with
> > >
> > > make -k check RUNTESTFLAGS="--target_board=sh-sim\{-m2/-ml,-m2/
> > > -mb,
> > > -m2a/-mb,-m4/-ml,-m4/-mb,-m4a/-ml,-m4a/-mb}"
> >
> > The attached patch removes some leftovers and reinstantes the
> > divsf3
> > expander pattern which got accidentally deleted by the previous
> > patch.
>
> The attached patch removes SH5 support from libgcc.
> Tested as above. Committed as r235640.
The attached patch removes SH5 checks in the testsuite.
Committed as r235673.
Cheers,
Oleg
testsuite/ChangeLog:
* g++.old-deja/g++.jason/thunk3.C: Remove SH5 checks.
* gcc.dg/20021029-1.c: Likewise.
* gcc.target/sh/attr-isr-trap_exit.c: Likewise.
* gcc.target/sh/attr-isr-trapa.c: Likewise.
* gcc.target/sh/cmpstr.c: Likewise.
* gcc.target/sh/cmpstrn.c: Likewise.
* gcc.target/sh/memset.c: Likewise.
* gcc.target/sh/pr21255-2-mb.c: Likewise.
* gcc.target/sh/pr21255-2-ml.c: Likewise.
* gcc.target/sh/pr39423-1.c: Likewise.
* gcc.target/sh/pr49468-di.c: Likewise.
* gcc.target/sh/pr49468-si.c: Likewise.
* gcc.target/sh/pr49880-1.c: Likewise.
* gcc.target/sh/pr49880-2.c: Likewise.
* gcc.target/sh/pr49880-3.c: Likewise.
* gcc.target/sh/pr50751-1.c: Likewise.
* gcc.target/sh/pr50751-4.c: Likewise.
* gcc.target/sh/pr50751-7.c: Likewise.
* gcc.target/sh/pr51244-1.c: Likewise.
* gcc.target/sh/pr51244-10.c: Likewise.
* gcc.target/sh/pr51244-11.c: Likewise.
* gcc.target/sh/pr51244-12.c: Likewise.
* gcc.target/sh/pr51244-13.c: Likewise.
* gcc.target/sh/pr51244-14.c: Likewise.
* gcc.target/sh/pr51244-17.c: Likewise.
* gcc.target/sh/pr51244-18.c: Likewise.
* gcc.target/sh/pr51244-19.c: Likewise.
* gcc.target/sh/pr51244-4.c: Likewise.
* gcc.target/sh/pr51244-5.c: Likewise.
* gcc.target/sh/pr51244-7.c: Likewise.
* gcc.target/sh/pr51244-8.c: Likewise.
* gcc.target/sh/pr51244-9.c: Likewise.
* gcc.target/sh/pr51697.c: Likewise.
* gcc.target/sh/pr52483-1.c: Likewise.
* gcc.target/sh/pr52483-2.c: Likewise.
* gcc.target/sh/pr52483-3.c: Likewise.
* gcc.target/sh/pr52483-5.c: Likewise.
* gcc.target/sh/pr52933-1.c: Likewise.
* gcc.target/sh/pr52933-2.c: Likewise.
* gcc.target/sh/pr52933-3.c: Likewise.
* gcc.target/sh/pr53568-1.c: Likewise.
* gcc.target/sh/pr53976-1.c: Likewise.
* gcc.target/sh/pr53988-1.c: Likewise.
* gcc.target/sh/pr53988.c: Likewise.
* gcc.target/sh/pr54089-1.c: Likewise.
* gcc.target/sh/pr54089-6.c: Likewise.
* gcc.target/sh/pr54089-7.c: Likewise.
* gcc.target/sh/pr54089-8.c: Likewise.
* gcc.target/sh/pr54089-9.c: Likewise.
* gcc.target/sh/pr54236-1.c: Likewise.
* gcc.target/sh/pr54236-2.c: Likewise.
* gcc.target/sh/pr54236-3.c: Likewise.
* gcc.target/sh/pr54236-4.c: Likewise.
* gcc.target/sh/pr54386.c: Likewise.
* gcc.target/sh/pr54602-1.c: Likewise.
* gcc.target/sh/pr54685.c: Likewise.
* gcc.target/sh/pr54760-1.c: Likewise.
* gcc.target/sh/pr54760-2.c: Likewise.
* gcc.target/sh/pr54760-3.c: Likewise.
* gcc.target/sh/pr54760-4.c: Likewise.
* gcc.target/sh/pr54760-5.c: Likewise.
* gcc.target/sh/pr54760-6.c: Likewise.
* gcc.target/sh/pr55146.c: Likewise.
* gcc.target/sh/pr55160.c: Likewise.
* gcc.target/sh/pr59278.c: Likewise.
* gcc.target/sh/pr59401-1.c: Likewise.
* gcc.target/sh/pr59533-1.c: Likewise.
* gcc.target/sh/pr63260.c: Likewise.
* gcc.target/sh/pragma-isr-trap-exit.c: Likewise.
* gcc.target/sh/pragma-isr-trapa.c: Likewise.
* gcc.target/sh/strlen.c: Likewise.
* gcc.target/sh/torture/pr30807.c: Likewise.
* gcc.target/sh/torture/pr34777.c: Likewise.
* gcc.target/sh/torture/pr64652.c: Likewise.
* gcc.target/sh/torture/pr65505.c: Likewise.
* gcc.target/sh/torture/pragma-isr.c: Likewise.
* gcc.target/sh/torture/pragma-isr2.c: Likewise.
[-- Attachment #2: remove_sh64_sh5_testsuite_5.patch --]
[-- Type: text/x-patch, Size: 38920 bytes --]
diff --git a/gcc/testsuite/g++.old-deja/g++.jason/thunk3.C b/gcc/testsuite/g++.old-deja/g++.jason/thunk3.C
index 7e0b93a..5ea46f5 100644
--- a/gcc/testsuite/g++.old-deja/g++.jason/thunk3.C
+++ b/gcc/testsuite/g++.old-deja/g++.jason/thunk3.C
@@ -1,5 +1,5 @@
// { dg-do run }
-// { dg-skip-if "fails with generic thunk support" { rs6000-*-* powerpc-*-eabi v850-*-* sh-*-* sh64-*-* h8*-*-* xtensa*-*-* m32r*-*-* lm32-*-* nios2-*-* } { "*" } { "" } }
+// { dg-skip-if "fails with generic thunk support" { rs6000-*-* powerpc-*-eabi v850-*-* sh-*-* h8*-*-* xtensa*-*-* m32r*-*-* lm32-*-* nios2-*-* } { "*" } { "" } }
// Test that variadic function calls using thunks work right.
// Note that this will break on any target that uses the generic thunk
// support, because it doesn't support variadic functions.
diff --git a/gcc/testsuite/gcc.dg/20021029-1.c b/gcc/testsuite/gcc.dg/20021029-1.c
index 9da8e81..f11a6e4 100644
--- a/gcc/testsuite/gcc.dg/20021029-1.c
+++ b/gcc/testsuite/gcc.dg/20021029-1.c
@@ -2,7 +2,6 @@
variables into writable sections. */
/* { dg-do compile { target fpic } } */
/* { dg-options "-O2 -fpic" } */
-/* { dg-options "-O2 -fpic -mpt-fixed" { target sh64*-*-* } } */
/* { dg-final { scan-assembler-not ".data.rel.ro.local" } } */
/* { dg-require-effective-target label_values } */
/* { dg-require-effective-target indirect_jumps } */
diff --git a/gcc/testsuite/gcc.target/sh/attr-isr-trap_exit.c b/gcc/testsuite/gcc.target/sh/attr-isr-trap_exit.c
index a45e92f..6c63ebf 100644
--- a/gcc/testsuite/gcc.target/sh/attr-isr-trap_exit.c
+++ b/gcc/testsuite/gcc.target/sh/attr-isr-trap_exit.c
@@ -1,7 +1,6 @@
/* Check that trapa / interrput_handler attributes can paired in
either order. */
/* { dg-do compile } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-options "-O" } */
/* { dg-final { scan-assembler "trapa\[ \t\]\[ \t\]*#4"} } */
/* { dg-final { scan-assembler-times "trapa" 1 } } */
diff --git a/gcc/testsuite/gcc.target/sh/attr-isr-trapa.c b/gcc/testsuite/gcc.target/sh/attr-isr-trapa.c
index 3f850ac..a0c45bb 100644
--- a/gcc/testsuite/gcc.target/sh/attr-isr-trapa.c
+++ b/gcc/testsuite/gcc.target/sh/attr-isr-trapa.c
@@ -1,6 +1,5 @@
/* Check that no interrupt-specific register saves are generated. */
/* { dg-do compile { target { { "sh*-*-*" } && nonpic } } } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-options "-O" } */
/* { dg-final { scan-assembler-times "rte" 1 } } */
/* { dg-final { scan-assembler-not "mov.l\tr\[0-9\],@-r15" } } */
diff --git a/gcc/testsuite/gcc.target/sh/cmpstr.c b/gcc/testsuite/gcc.target/sh/cmpstr.c
index 1b45089..e8f1de7 100644
--- a/gcc/testsuite/gcc.target/sh/cmpstr.c
+++ b/gcc/testsuite/gcc.target/sh/cmpstr.c
@@ -2,7 +2,6 @@
when optimizing for speed. */
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-final { scan-assembler-not "jmp" } } */
/* { dg-final { scan-assembler-times "cmp/str" 3 } } */
/* { dg-final { scan-assembler-times "tst\t#3" 2 } } */
diff --git a/gcc/testsuite/gcc.target/sh/cmpstrn.c b/gcc/testsuite/gcc.target/sh/cmpstrn.c
index 65cb9d6..6dd1151 100644
--- a/gcc/testsuite/gcc.target/sh/cmpstrn.c
+++ b/gcc/testsuite/gcc.target/sh/cmpstrn.c
@@ -2,7 +2,6 @@
when optimizing for speed. */
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-final { scan-assembler-not "jmp" } } */
/* { dg-final { scan-assembler-times "cmp/str" 1 } } */
diff --git a/gcc/testsuite/gcc.target/sh/memset.c b/gcc/testsuite/gcc.target/sh/memset.c
index 4695db3..e888d1d 100644
--- a/gcc/testsuite/gcc.target/sh/memset.c
+++ b/gcc/testsuite/gcc.target/sh/memset.c
@@ -2,7 +2,6 @@
optimizing for speed. */
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-final { scan-assembler-not "jmp" } } */
void
diff --git a/gcc/testsuite/gcc.target/sh/pr21255-2-mb.c b/gcc/testsuite/gcc.target/sh/pr21255-2-mb.c
index 531ed39..b9063de 100644
--- a/gcc/testsuite/gcc.target/sh/pr21255-2-mb.c
+++ b/gcc/testsuite/gcc.target/sh/pr21255-2-mb.c
@@ -1,5 +1,5 @@
-/* { dg-do compile } */
-/* { dg-options "-mb -O2 -fomit-frame-pointer" } */
+/* { dg-do compile { target { big_endian } } } */
+/* { dg-options "-O2 -fomit-frame-pointer" } */
/* { dg-final { scan-assembler "mov @r.,r.; mov @\\(4,r.\\),r." } } */
double d;
@@ -10,10 +10,6 @@ f (void)
/* If -ml from the target options is passed after -mb from dg-options, we
end up with th reverse endianness. */
-#if TARGET_SHMEDIA || defined (__LITTLE_ENDIAN__)
- asm ("mov @r1,r3; mov @(4,r1),r4");
-#else
asm ("mov %S1,%S0; mov %R1,%R0" : "=&r" (r) : "m" (d));
-#endif
return r;
}
diff --git a/gcc/testsuite/gcc.target/sh/pr21255-2-ml.c b/gcc/testsuite/gcc.target/sh/pr21255-2-ml.c
index 6948f47..10412f1 100644
--- a/gcc/testsuite/gcc.target/sh/pr21255-2-ml.c
+++ b/gcc/testsuite/gcc.target/sh/pr21255-2-ml.c
@@ -1,6 +1,5 @@
-/* { dg-do compile } */
+/* { dg-do compile { target { little_endian } } } */
/* { dg-options "-O2 -fomit-frame-pointer" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-mb" && "-m5*"} { "" } } */
/* { dg-final { scan-assembler "mov @\\(4,r.\\),r.; mov @r.,r." } } */
double d;
diff --git a/gcc/testsuite/gcc.target/sh/pr39423-1.c b/gcc/testsuite/gcc.target/sh/pr39423-1.c
index 1e02937..8bf87b5 100644
--- a/gcc/testsuite/gcc.target/sh/pr39423-1.c
+++ b/gcc/testsuite/gcc.target/sh/pr39423-1.c
@@ -2,7 +2,6 @@
small offset, instead of re-calculating the index. */
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-not "add\t#1" } } */
int
diff --git a/gcc/testsuite/gcc.target/sh/pr49468-di.c b/gcc/testsuite/gcc.target/sh/pr49468-di.c
index 4b17fce..6f6611f 100644
--- a/gcc/testsuite/gcc.target/sh/pr49468-di.c
+++ b/gcc/testsuite/gcc.target/sh/pr49468-di.c
@@ -2,7 +2,6 @@
and conditional branch instead of default branch-free code. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-times "negc" 4 } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr49468-si.c b/gcc/testsuite/gcc.target/sh/pr49468-si.c
index 8c771ed..2b25920 100644
--- a/gcc/testsuite/gcc.target/sh/pr49468-si.c
+++ b/gcc/testsuite/gcc.target/sh/pr49468-si.c
@@ -2,7 +2,6 @@
conditional branch instead of default branch-free code. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-times "neg" 2 } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr49880-1.c b/gcc/testsuite/gcc.target/sh/pr49880-1.c
index 249fae0..db30875 100644
--- a/gcc/testsuite/gcc.target/sh/pr49880-1.c
+++ b/gcc/testsuite/gcc.target/sh/pr49880-1.c
@@ -1,7 +1,6 @@
/* Check that the option -mdiv=call-div1 works. */
/* { dg-do link } */
/* { dg-options "-mdiv=call-div1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
int
test00 (int a, int b)
diff --git a/gcc/testsuite/gcc.target/sh/pr49880-2.c b/gcc/testsuite/gcc.target/sh/pr49880-2.c
index 35e23de..193b95c 100644
--- a/gcc/testsuite/gcc.target/sh/pr49880-2.c
+++ b/gcc/testsuite/gcc.target/sh/pr49880-2.c
@@ -1,7 +1,6 @@
/* Check that the option -mdiv=call-fp works. */
/* { dg-do link } */
/* { dg-options "-mdiv=call-fp" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
int
test00 (int a, int b)
diff --git a/gcc/testsuite/gcc.target/sh/pr49880-3.c b/gcc/testsuite/gcc.target/sh/pr49880-3.c
index be6ea52..dd4f9b2 100644
--- a/gcc/testsuite/gcc.target/sh/pr49880-3.c
+++ b/gcc/testsuite/gcc.target/sh/pr49880-3.c
@@ -1,7 +1,6 @@
/* Check that the option -mdiv=call-table works. */
/* { dg-do link } */
/* { dg-options "-mdiv=call-table" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
int
test00 (int a, int b)
diff --git a/gcc/testsuite/gcc.target/sh/pr50751-1.c b/gcc/testsuite/gcc.target/sh/pr50751-1.c
index 80c63fb..d4a3c86 100644
--- a/gcc/testsuite/gcc.target/sh/pr50751-1.c
+++ b/gcc/testsuite/gcc.target/sh/pr50751-1.c
@@ -3,7 +3,6 @@
calculations outside the mov insns. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-not "add|sub" } } */
void
diff --git a/gcc/testsuite/gcc.target/sh/pr50751-4.c b/gcc/testsuite/gcc.target/sh/pr50751-4.c
index e0f3ab7..492ceff 100644
--- a/gcc/testsuite/gcc.target/sh/pr50751-4.c
+++ b/gcc/testsuite/gcc.target/sh/pr50751-4.c
@@ -3,7 +3,6 @@
calculations outside the mov insns. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-not "add|sub" } } */
void
diff --git a/gcc/testsuite/gcc.target/sh/pr50751-7.c b/gcc/testsuite/gcc.target/sh/pr50751-7.c
index 014575a..9aa84b3 100644
--- a/gcc/testsuite/gcc.target/sh/pr50751-7.c
+++ b/gcc/testsuite/gcc.target/sh/pr50751-7.c
@@ -3,7 +3,6 @@
outside the mov insns. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-not "add|sub" } } */
typedef struct
diff --git a/gcc/testsuite/gcc.target/sh/pr51244-1.c b/gcc/testsuite/gcc.target/sh/pr51244-1.c
index 15e2ebd..1da824d 100644
--- a/gcc/testsuite/gcc.target/sh/pr51244-1.c
+++ b/gcc/testsuite/gcc.target/sh/pr51244-1.c
@@ -3,7 +3,6 @@
test instructions. */
/* { dg-do compile } */
/* { dg-options "-O1 -mbranch-cost=2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-not "movt|tst|negc|extu" } } */
int
diff --git a/gcc/testsuite/gcc.target/sh/pr51244-10.c b/gcc/testsuite/gcc.target/sh/pr51244-10.c
index ef16b75..bbbd813 100644
--- a/gcc/testsuite/gcc.target/sh/pr51244-10.c
+++ b/gcc/testsuite/gcc.target/sh/pr51244-10.c
@@ -12,7 +12,6 @@
*/
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-final { scan-assembler-not "shll|subc|and" } } */
int
test_00 (int* p)
diff --git a/gcc/testsuite/gcc.target/sh/pr51244-11.c b/gcc/testsuite/gcc.target/sh/pr51244-11.c
index b673e9a..fea7f6c 100644
--- a/gcc/testsuite/gcc.target/sh/pr51244-11.c
+++ b/gcc/testsuite/gcc.target/sh/pr51244-11.c
@@ -2,7 +2,6 @@
execution patterns. */
/* { dg-do compile } */
/* { dg-options "-O1 -mzdcbranch" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-final { scan-assembler-not "subc|and" } } */
int*
diff --git a/gcc/testsuite/gcc.target/sh/pr51244-12.c b/gcc/testsuite/gcc.target/sh/pr51244-12.c
index 027c5ab..f0c62e6 100644
--- a/gcc/testsuite/gcc.target/sh/pr51244-12.c
+++ b/gcc/testsuite/gcc.target/sh/pr51244-12.c
@@ -3,7 +3,6 @@
which handles the inverted case does not work properly. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-final { scan-assembler-times "negc" 15 { target { ! sh2a } } } } */
/* { dg-final { scan-assembler-times "addc" 3 { target { ! sh2a } } } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr51244-13.c b/gcc/testsuite/gcc.target/sh/pr51244-13.c
index f9a851d..04937e6 100644
--- a/gcc/testsuite/gcc.target/sh/pr51244-13.c
+++ b/gcc/testsuite/gcc.target/sh/pr51244-13.c
@@ -10,7 +10,6 @@
insns. */
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-final { scan-assembler-times "tst" 2 } } */
void printk (const char*, const char*, int);
diff --git a/gcc/testsuite/gcc.target/sh/pr51244-14.c b/gcc/testsuite/gcc.target/sh/pr51244-14.c
index 61a5dc93..70d6893 100644
--- a/gcc/testsuite/gcc.target/sh/pr51244-14.c
+++ b/gcc/testsuite/gcc.target/sh/pr51244-14.c
@@ -12,7 +12,6 @@
patterns, we only check for the extu. */
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-final { scan-assembler-not "extu" } } */
typedef struct transaction_s transaction_t;
diff --git a/gcc/testsuite/gcc.target/sh/pr51244-17.c b/gcc/testsuite/gcc.target/sh/pr51244-17.c
index 621abb7..06c77cd 100644
--- a/gcc/testsuite/gcc.target/sh/pr51244-17.c
+++ b/gcc/testsuite/gcc.target/sh/pr51244-17.c
@@ -2,7 +2,6 @@
results of arithmetic with T bit inputs. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-final { scan-assembler-not "extu|exts" } } */
int
diff --git a/gcc/testsuite/gcc.target/sh/pr51244-18.c b/gcc/testsuite/gcc.target/sh/pr51244-18.c
index 19b244c..93dbcac 100644
--- a/gcc/testsuite/gcc.target/sh/pr51244-18.c
+++ b/gcc/testsuite/gcc.target/sh/pr51244-18.c
@@ -14,7 +14,6 @@
reload. */
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-final { scan-assembler-not "movt|tst" } } */
typedef char Char;
diff --git a/gcc/testsuite/gcc.target/sh/pr51244-19.c b/gcc/testsuite/gcc.target/sh/pr51244-19.c
index 5845d93..328099d 100644
--- a/gcc/testsuite/gcc.target/sh/pr51244-19.c
+++ b/gcc/testsuite/gcc.target/sh/pr51244-19.c
@@ -25,7 +25,6 @@
reload. */
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-final { scan-assembler-not "movt" } } */
struct request
diff --git a/gcc/testsuite/gcc.target/sh/pr51244-4.c b/gcc/testsuite/gcc.target/sh/pr51244-4.c
index ac967bf..9d9361c 100644
--- a/gcc/testsuite/gcc.target/sh/pr51244-4.c
+++ b/gcc/testsuite/gcc.target/sh/pr51244-4.c
@@ -2,7 +2,6 @@
uses the subc instruction. */
/* { dg-do compile } */
/* { dg-options "-O1 -mbranch-cost=2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-not "movt|tst|negc|movrt" } } */
/* { dg-final { scan-assembler-times "subc" 3 } } */
/* { dg-final { scan-assembler-times "not\t" 1 } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr51244-5.c b/gcc/testsuite/gcc.target/sh/pr51244-5.c
index c0f05a1..4c7d5bf 100644
--- a/gcc/testsuite/gcc.target/sh/pr51244-5.c
+++ b/gcc/testsuite/gcc.target/sh/pr51244-5.c
@@ -2,7 +2,6 @@
a negc or movrt insn that stores the inverted T bit in a reg. */
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-final { scan-assembler-not "extu|exts" } } */
int
diff --git a/gcc/testsuite/gcc.target/sh/pr51244-7.c b/gcc/testsuite/gcc.target/sh/pr51244-7.c
index d4d3974..69f890d 100644
--- a/gcc/testsuite/gcc.target/sh/pr51244-7.c
+++ b/gcc/testsuite/gcc.target/sh/pr51244-7.c
@@ -12,7 +12,6 @@
*/
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-final { scan-assembler-not "cmp/hi" } } */
/* { dg-final { scan-assembler-not "mov\t#0" } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr51244-8.c b/gcc/testsuite/gcc.target/sh/pr51244-8.c
index d8c1269..fbd948b 100644
--- a/gcc/testsuite/gcc.target/sh/pr51244-8.c
+++ b/gcc/testsuite/gcc.target/sh/pr51244-8.c
@@ -8,7 +8,6 @@
*/
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-final { scan-assembler-not "shad|neg" } } */
int test_01_00 (int*, void*);
diff --git a/gcc/testsuite/gcc.target/sh/pr51244-9.c b/gcc/testsuite/gcc.target/sh/pr51244-9.c
index cca90a8..af8a465 100644
--- a/gcc/testsuite/gcc.target/sh/pr51244-9.c
+++ b/gcc/testsuite/gcc.target/sh/pr51244-9.c
@@ -10,7 +10,6 @@
*/
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-final { scan-assembler-not "mov\t#0" } } */
static inline unsigned int
test_03_00 (unsigned int x)
diff --git a/gcc/testsuite/gcc.target/sh/pr51697.c b/gcc/testsuite/gcc.target/sh/pr51697.c
index d63e329..0107e29 100644
--- a/gcc/testsuite/gcc.target/sh/pr51697.c
+++ b/gcc/testsuite/gcc.target/sh/pr51697.c
@@ -2,7 +2,6 @@
with -Os. */
/* { dg-do compile } */
/* { dg-options "-Os" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-times "tst" 2 } } */
/* { dg-final { scan-assembler-not "cmp" } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr52483-1.c b/gcc/testsuite/gcc.target/sh/pr52483-1.c
index ca64a0a..7a1c202 100644
--- a/gcc/testsuite/gcc.target/sh/pr52483-1.c
+++ b/gcc/testsuite/gcc.target/sh/pr52483-1.c
@@ -2,7 +2,6 @@
sign/zero extensions. */
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-not "exts|extu" } } */
int
diff --git a/gcc/testsuite/gcc.target/sh/pr52483-2.c b/gcc/testsuite/gcc.target/sh/pr52483-2.c
index 68e7f8e..91b485e 100644
--- a/gcc/testsuite/gcc.target/sh/pr52483-2.c
+++ b/gcc/testsuite/gcc.target/sh/pr52483-2.c
@@ -2,7 +2,6 @@
addressing modes and do not result in redundant sign/zero extensions. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-times "@\\(5," 4 } } */
/* { dg-final { scan-assembler-times "@\\(10," 4 } } */
/* { dg-final { scan-assembler-times "@\\(20," 4 } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr52483-3.c b/gcc/testsuite/gcc.target/sh/pr52483-3.c
index baeec33..e0a02e0 100644
--- a/gcc/testsuite/gcc.target/sh/pr52483-3.c
+++ b/gcc/testsuite/gcc.target/sh/pr52483-3.c
@@ -2,7 +2,6 @@
modes and do not result in redundant sign/zero extensions. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-times "@\\(r0," 6 } } */
/* { dg-final { scan-assembler-not "exts|extu" } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr52483-5.c b/gcc/testsuite/gcc.target/sh/pr52483-5.c
index 50aefe2..947e8df 100644
--- a/gcc/testsuite/gcc.target/sh/pr52483-5.c
+++ b/gcc/testsuite/gcc.target/sh/pr52483-5.c
@@ -2,7 +2,6 @@
modes and do not result in redundant sign extensions. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-times "@r\[0-9\]\+\\+," 3 } } */
/* { dg-final { scan-assembler-not "exts" } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr52933-1.c b/gcc/testsuite/gcc.target/sh/pr52933-1.c
index 0c69027..138de7f 100644
--- a/gcc/testsuite/gcc.target/sh/pr52933-1.c
+++ b/gcc/testsuite/gcc.target/sh/pr52933-1.c
@@ -4,7 +4,6 @@
logic usually show up as redundant tst insns. */
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-final { scan-assembler-times "div0s" 32 } } */
/* { dg-final { scan-assembler-not "tst" } } */
/* { dg-final { scan-assembler-not "not\t" } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr52933-2.c b/gcc/testsuite/gcc.target/sh/pr52933-2.c
index 67e2753..4637f0e 100644
--- a/gcc/testsuite/gcc.target/sh/pr52933-2.c
+++ b/gcc/testsuite/gcc.target/sh/pr52933-2.c
@@ -5,7 +5,6 @@
logic usually show up as redundant tst insns. */
/* { dg-do compile } */
/* { dg-options "-O2 -mpretend-cmove" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-final { scan-assembler-times "div0s" 32 } } */
/* { dg-final { scan-assembler-not "tst" } } */
/* { dg-final { scan-assembler-not "not\t" } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr52933-3.c b/gcc/testsuite/gcc.target/sh/pr52933-3.c
index fadcc9e..1b563fe 100644
--- a/gcc/testsuite/gcc.target/sh/pr52933-3.c
+++ b/gcc/testsuite/gcc.target/sh/pr52933-3.c
@@ -1,7 +1,6 @@
/* Check that the div0s instruction is used for integer sign comparisons. */
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-final { scan-assembler-times "div0s" 2 } } */
typedef struct { unsigned int arg[100]; } *FunctionCallInfo;
diff --git a/gcc/testsuite/gcc.target/sh/pr53568-1.c b/gcc/testsuite/gcc.target/sh/pr53568-1.c
index e274170..673d0a1 100644
--- a/gcc/testsuite/gcc.target/sh/pr53568-1.c
+++ b/gcc/testsuite/gcc.target/sh/pr53568-1.c
@@ -2,7 +2,6 @@
instructions. */
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-times "swap.w" 7 } } */
/* { dg-final { scan-assembler-times "swap.b" 16 } } */
/* { dg-final { scan-assembler-times "extu.w" 2 } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr53976-1.c b/gcc/testsuite/gcc.target/sh/pr53976-1.c
index 68f8cdc..716a009 100644
--- a/gcc/testsuite/gcc.target/sh/pr53976-1.c
+++ b/gcc/testsuite/gcc.target/sh/pr53976-1.c
@@ -2,7 +2,6 @@
works as expected. */
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-final { scan-assembler-times "clrt" 2 } } */
/* { dg-final { scan-assembler-times "sett" 1 } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr53988-1.c b/gcc/testsuite/gcc.target/sh/pr53988-1.c
index 4e0d49e..4db7b70 100644
--- a/gcc/testsuite/gcc.target/sh/pr53988-1.c
+++ b/gcc/testsuite/gcc.target/sh/pr53988-1.c
@@ -2,7 +2,6 @@
tst Rm,Rn instruction is used. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-times "tst\tr" 8 } } */
/* { dg-final { scan-assembler-times "mov.b" 4 } } */
/* { dg-final { scan-assembler-times "mov.w" 4 } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr53988.c b/gcc/testsuite/gcc.target/sh/pr53988.c
index a2e7213..3e21351 100644
--- a/gcc/testsuite/gcc.target/sh/pr53988.c
+++ b/gcc/testsuite/gcc.target/sh/pr53988.c
@@ -4,7 +4,6 @@
movu insn. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-times "tst\tr" 8 } } */
/* { dg-final { scan-assembler-not "tst\t#255" } } */
/* { dg-final { scan-assembler-not "exts|extu|and|movu" } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr54089-1.c b/gcc/testsuite/gcc.target/sh/pr54089-1.c
index 418ba69..64f79eb 100644
--- a/gcc/testsuite/gcc.target/sh/pr54089-1.c
+++ b/gcc/testsuite/gcc.target/sh/pr54089-1.c
@@ -1,7 +1,6 @@
/* Check that the rotcr instruction is generated. */
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-times "rotcr" 24 } } */
/* { dg-final { scan-assembler-times "shll\t" 1 } } */
/* { dg-final { scan-assembler-not "and\t#1" } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr54089-6.c b/gcc/testsuite/gcc.target/sh/pr54089-6.c
index 577690d..e8daa29 100644
--- a/gcc/testsuite/gcc.target/sh/pr54089-6.c
+++ b/gcc/testsuite/gcc.target/sh/pr54089-6.c
@@ -1,7 +1,6 @@
/* Check that the rotr and rotl instructions are generated. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-final { scan-assembler-times "rotr" 2 } } */
/* { dg-final { scan-assembler-times "rotl" 3 } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr54089-7.c b/gcc/testsuite/gcc.target/sh/pr54089-7.c
index 0476f75..b302364 100644
--- a/gcc/testsuite/gcc.target/sh/pr54089-7.c
+++ b/gcc/testsuite/gcc.target/sh/pr54089-7.c
@@ -1,7 +1,6 @@
/* Check that the rotcr instruction is generated. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-times "rotcr" 4 } } */
/* { dg-final { scan-assembler-not "movt" } } */
/* { dg-final { scan-assembler-not "or\t" } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr54089-8.c b/gcc/testsuite/gcc.target/sh/pr54089-8.c
index 20b0098..6af1750 100644
--- a/gcc/testsuite/gcc.target/sh/pr54089-8.c
+++ b/gcc/testsuite/gcc.target/sh/pr54089-8.c
@@ -1,7 +1,6 @@
/* Check that the rotcl instruction is generated. */
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-times "rotcl" 28 } } */
typedef char bool;
diff --git a/gcc/testsuite/gcc.target/sh/pr54089-9.c b/gcc/testsuite/gcc.target/sh/pr54089-9.c
index 8aa15df..3ced51e 100644
--- a/gcc/testsuite/gcc.target/sh/pr54089-9.c
+++ b/gcc/testsuite/gcc.target/sh/pr54089-9.c
@@ -1,7 +1,6 @@
/* Check that the rotcr instruction is generated. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-times "rotcl" 4 } } */
/* { dg-final { scan-assembler-not "movt" } } */
/* { dg-final { scan-assembler-not "or\t" } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr54236-1.c b/gcc/testsuite/gcc.target/sh/pr54236-1.c
index 31008ca..0b52a6a 100644
--- a/gcc/testsuite/gcc.target/sh/pr54236-1.c
+++ b/gcc/testsuite/gcc.target/sh/pr54236-1.c
@@ -3,7 +3,7 @@
movt instructions in these cases. */
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
+
/* { dg-final { scan-assembler-times "addc" 6 } } */
/* { dg-final { scan-assembler-times "subc" 4 } } */
/* { dg-final { scan-assembler-times "sett" 5 } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr54236-2.c b/gcc/testsuite/gcc.target/sh/pr54236-2.c
index b6c2493..1e2f3bb 100644
--- a/gcc/testsuite/gcc.target/sh/pr54236-2.c
+++ b/gcc/testsuite/gcc.target/sh/pr54236-2.c
@@ -3,7 +3,7 @@
these cases. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
+
/* { dg-final { scan-assembler-times "addc" 36 } } */
/* { dg-final { scan-assembler-times "shll" 14 } } */
/* { dg-final { scan-assembler-times "add\tr" 12 } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr54236-3.c b/gcc/testsuite/gcc.target/sh/pr54236-3.c
index 933ece3..cd3d353 100644
--- a/gcc/testsuite/gcc.target/sh/pr54236-3.c
+++ b/gcc/testsuite/gcc.target/sh/pr54236-3.c
@@ -3,7 +3,6 @@
these cases. */
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-times "addc" 4 } } */
/* { dg-final { scan-assembler-times "subc" 5 } } */
/* { dg-final { scan-assembler-times "movt" 1 } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr54236-4.c b/gcc/testsuite/gcc.target/sh/pr54236-4.c
index dce413e..4a3ffd1 100644
--- a/gcc/testsuite/gcc.target/sh/pr54236-4.c
+++ b/gcc/testsuite/gcc.target/sh/pr54236-4.c
@@ -2,7 +2,7 @@
inverted. */
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
+
/* { dg-final { scan-assembler-times "cmp/eq" 7 } } */
/* { dg-final { scan-assembler-times "subc" 5 { target { ! sh2a } } } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr54386.c b/gcc/testsuite/gcc.target/sh/pr54386.c
index ec52d89..b04b212 100644
--- a/gcc/testsuite/gcc.target/sh/pr54386.c
+++ b/gcc/testsuite/gcc.target/sh/pr54386.c
@@ -1,7 +1,6 @@
/* Check that the inlined mem load is not handled as unaligned load. */
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-not "shll|extu|or" } } */
static inline int
diff --git a/gcc/testsuite/gcc.target/sh/pr54602-1.c b/gcc/testsuite/gcc.target/sh/pr54602-1.c
index bd402b3..e7fb2a9 100644
--- a/gcc/testsuite/gcc.target/sh/pr54602-1.c
+++ b/gcc/testsuite/gcc.target/sh/pr54602-1.c
@@ -3,7 +3,6 @@
expected we won't see any nop insns. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-not "nop" } } */
int test00 (int a, int b);
diff --git a/gcc/testsuite/gcc.target/sh/pr54685.c b/gcc/testsuite/gcc.target/sh/pr54685.c
index 111a120..ed84a32 100644
--- a/gcc/testsuite/gcc.target/sh/pr54685.c
+++ b/gcc/testsuite/gcc.target/sh/pr54685.c
@@ -2,7 +2,6 @@
utilizing the cmp/pz instruction. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-not "not\[ \t\]" } } */
/* { dg-final { scan-assembler-times "cmp/pz" 7 } } */
/* { dg-final { scan-assembler-times "shll" 1 } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr54760-1.c b/gcc/testsuite/gcc.target/sh/pr54760-1.c
index 4437511..8bc5836 100644
--- a/gcc/testsuite/gcc.target/sh/pr54760-1.c
+++ b/gcc/testsuite/gcc.target/sh/pr54760-1.c
@@ -2,7 +2,6 @@
built-in functions result in gbr store / load instructions. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-times "ldc" 1 } } */
/* { dg-final { scan-assembler-times "stc" 1 } } */
/* { dg-final { scan-assembler-times "gbr" 2 } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr54760-2.c b/gcc/testsuite/gcc.target/sh/pr54760-2.c
index 4a3561a..bad478c 100644
--- a/gcc/testsuite/gcc.target/sh/pr54760-2.c
+++ b/gcc/testsuite/gcc.target/sh/pr54760-2.c
@@ -3,7 +3,6 @@
instruction something is not working properly. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-times "stc\tgbr" 0 } } */
/* ---------------------------------------------------------------------------
diff --git a/gcc/testsuite/gcc.target/sh/pr54760-3.c b/gcc/testsuite/gcc.target/sh/pr54760-3.c
index 678fb39..617a66b 100644
--- a/gcc/testsuite/gcc.target/sh/pr54760-3.c
+++ b/gcc/testsuite/gcc.target/sh/pr54760-3.c
@@ -4,7 +4,6 @@
independent thread_pointer built-in functions available. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
int
test00 (void* p, int x)
diff --git a/gcc/testsuite/gcc.target/sh/pr54760-4.c b/gcc/testsuite/gcc.target/sh/pr54760-4.c
index d218281..bc7cefd 100644
--- a/gcc/testsuite/gcc.target/sh/pr54760-4.c
+++ b/gcc/testsuite/gcc.target/sh/pr54760-4.c
@@ -3,7 +3,6 @@
register, i.e. it is invalidated by function calls. */
/* { dg-do compile } */
/* { dg-options "-O1 -fcall-used-gbr" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler "stc\tgbr" } } */
extern int test00 (void);
diff --git a/gcc/testsuite/gcc.target/sh/pr54760-5.c b/gcc/testsuite/gcc.target/sh/pr54760-5.c
index 30dfd31..824025d 100644
--- a/gcc/testsuite/gcc.target/sh/pr54760-5.c
+++ b/gcc/testsuite/gcc.target/sh/pr54760-5.c
@@ -3,7 +3,6 @@
call saved register. */
/* { dg-do compile } */
/* { dg-options "-O1 -fcall-saved-gbr" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-not "stc\tgbr" } } */
typedef struct
diff --git a/gcc/testsuite/gcc.target/sh/pr54760-6.c b/gcc/testsuite/gcc.target/sh/pr54760-6.c
index 4bf94c3..59f0d75 100644
--- a/gcc/testsuite/gcc.target/sh/pr54760-6.c
+++ b/gcc/testsuite/gcc.target/sh/pr54760-6.c
@@ -3,7 +3,6 @@
are. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-not "stc\tgbr" } } */
typedef struct
diff --git a/gcc/testsuite/gcc.target/sh/pr55146.c b/gcc/testsuite/gcc.target/sh/pr55146.c
index 91f0935..ef6ecd1 100644
--- a/gcc/testsuite/gcc.target/sh/pr55146.c
+++ b/gcc/testsuite/gcc.target/sh/pr55146.c
@@ -1,7 +1,6 @@
/* Check that the 'extu.b' instruction is generated for short jump tables. */
/* { dg-do compile } */
/* { dg-options "-Os" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler "extu.b" } } */
int
diff --git a/gcc/testsuite/gcc.target/sh/pr55160.c b/gcc/testsuite/gcc.target/sh/pr55160.c
index dca15c9..996c4ca 100644
--- a/gcc/testsuite/gcc.target/sh/pr55160.c
+++ b/gcc/testsuite/gcc.target/sh/pr55160.c
@@ -1,7 +1,6 @@
/* Check that the decrement-and-test instruction is generated. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-times "dt\tr" 2 } } */
int
diff --git a/gcc/testsuite/gcc.target/sh/pr59278.c b/gcc/testsuite/gcc.target/sh/pr59278.c
index 563e5b7..2040ffa 100644
--- a/gcc/testsuite/gcc.target/sh/pr59278.c
+++ b/gcc/testsuite/gcc.target/sh/pr59278.c
@@ -1,7 +1,6 @@
/* Check that combine considers unused regs dead. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler "addc" } } */
struct result
diff --git a/gcc/testsuite/gcc.target/sh/pr59401-1.c b/gcc/testsuite/gcc.target/sh/pr59401-1.c
index a2afe1a..408a270 100644
--- a/gcc/testsuite/gcc.target/sh/pr59401-1.c
+++ b/gcc/testsuite/gcc.target/sh/pr59401-1.c
@@ -3,7 +3,6 @@
and a GBR memory access must not be done. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler "stc\tgbr" } } */
/* { dg-final { scan-assembler "bf|bt" } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr59533-1.c b/gcc/testsuite/gcc.target/sh/pr59533-1.c
index c5c6c7e..b046985 100644
--- a/gcc/testsuite/gcc.target/sh/pr59533-1.c
+++ b/gcc/testsuite/gcc.target/sh/pr59533-1.c
@@ -1,7 +1,6 @@
/* Check that the cmp/pz instruction is generated as expected. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-times "shll" 1 } } */
/* { dg-final { scan-assembler-times "movt" 5 } } */
diff --git a/gcc/testsuite/gcc.target/sh/pr63260.c b/gcc/testsuite/gcc.target/sh/pr63260.c
index d01885f..ceff756 100644
--- a/gcc/testsuite/gcc.target/sh/pr63260.c
+++ b/gcc/testsuite/gcc.target/sh/pr63260.c
@@ -2,7 +2,6 @@
fabs instructions. */
/* { dg-do compile } */
/* { dg-options "-O1" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*"} { "" } } */
/* { dg-final { scan-assembler-not "fpscr|fpchg" } } */
float
diff --git a/gcc/testsuite/gcc.target/sh/pragma-isr-trap-exit.c b/gcc/testsuite/gcc.target/sh/pragma-isr-trap-exit.c
index 6dbd8e7..2a6728f 100644
--- a/gcc/testsuite/gcc.target/sh/pragma-isr-trap-exit.c
+++ b/gcc/testsuite/gcc.target/sh/pragma-isr-trap-exit.c
@@ -1,6 +1,5 @@
/* Check whether trapa is generated only for an ISR. */
/* { dg-do compile } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-options "-O" } */
/* { dg-final { scan-assembler-times "trapa\[ \t\]\[ \t\]*#4" 1 } } */
diff --git a/gcc/testsuite/gcc.target/sh/pragma-isr-trapa.c b/gcc/testsuite/gcc.target/sh/pragma-isr-trapa.c
index b70be6e..d2a9e60 100644
--- a/gcc/testsuite/gcc.target/sh/pragma-isr-trapa.c
+++ b/gcc/testsuite/gcc.target/sh/pragma-isr-trapa.c
@@ -1,6 +1,5 @@
/* Check that no interrupt-specific register saves are generated. */
/* { dg-do compile { target { { "sh*-*-*" } && nonpic } } } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-options "-O" } */
/* { dg-final { scan-assembler-times "rte" 1 } } */
/* { dg-final { scan-assembler-not "mov.l\tr\[0-9\],@-r15" } } */
diff --git a/gcc/testsuite/gcc.target/sh/strlen.c b/gcc/testsuite/gcc.target/sh/strlen.c
index 7f2d519..ca88026 100644
--- a/gcc/testsuite/gcc.target/sh/strlen.c
+++ b/gcc/testsuite/gcc.target/sh/strlen.c
@@ -2,7 +2,6 @@
when optimizing for speed. */
/* { dg-do compile } */
/* { dg-options "-O2" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-final { scan-assembler-not "jmp" } } */
/* { dg-final { scan-assembler-times "cmp/str" 2 } } */
/* { dg-final { scan-assembler-times "tst\t#3" 1 } } */
diff --git a/gcc/testsuite/gcc.target/sh/torture/pr30807.c b/gcc/testsuite/gcc.target/sh/torture/pr30807.c
index c9cc771..256d419 100644
--- a/gcc/testsuite/gcc.target/sh/torture/pr30807.c
+++ b/gcc/testsuite/gcc.target/sh/torture/pr30807.c
@@ -1,6 +1,5 @@
/* { dg-do compile } */
/* { dg-additional-options "-fpic -std=c99" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
typedef unsigned int size_t;
typedef struct
diff --git a/gcc/testsuite/gcc.target/sh/torture/pr34777.c b/gcc/testsuite/gcc.target/sh/torture/pr34777.c
index de6ba02..052709e 100644
--- a/gcc/testsuite/gcc.target/sh/torture/pr34777.c
+++ b/gcc/testsuite/gcc.target/sh/torture/pr34777.c
@@ -1,6 +1,5 @@
/* { dg-do compile } */
/* { dg-additional-options "-fschedule-insns -fPIC -mprefergot" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
static __inline __attribute__ ((__always_inline__)) void *
_dl_mmap (void * start, int length, int prot, int flags, int fd,
diff --git a/gcc/testsuite/gcc.target/sh/torture/pr64652.c b/gcc/testsuite/gcc.target/sh/torture/pr64652.c
index 8144311..eeb1c42 100644
--- a/gcc/testsuite/gcc.target/sh/torture/pr64652.c
+++ b/gcc/testsuite/gcc.target/sh/torture/pr64652.c
@@ -1,7 +1,6 @@
/* Check that using -mdiv=call-fp compiles without fuzz. */
/* { dg-do compile } */
/* { dg-additional-options "-mdiv=call-fp" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
int
test_0 (int a, int b, int c, int d)
diff --git a/gcc/testsuite/gcc.target/sh/torture/pr65505.c b/gcc/testsuite/gcc.target/sh/torture/pr65505.c
index 3e93002..934092c 100644
--- a/gcc/testsuite/gcc.target/sh/torture/pr65505.c
+++ b/gcc/testsuite/gcc.target/sh/torture/pr65505.c
@@ -1,6 +1,5 @@
/* { dg-do compile } */
/* { dg-additional-options "-std=gnu99" } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
struct thread_info {
struct task_struct *task;
diff --git a/gcc/testsuite/gcc.target/sh/torture/pragma-isr.c b/gcc/testsuite/gcc.target/sh/torture/pragma-isr.c
index 9e665ba..66e71f4 100644
--- a/gcc/testsuite/gcc.target/sh/torture/pragma-isr.c
+++ b/gcc/testsuite/gcc.target/sh/torture/pragma-isr.c
@@ -1,6 +1,5 @@
/* Check whether rte is generated for two ISRs. */
/* { dg-do compile } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-final { scan-assembler-times "rte" 2 } } */
extern void foo (void);
diff --git a/gcc/testsuite/gcc.target/sh/torture/pragma-isr2.c b/gcc/testsuite/gcc.target/sh/torture/pragma-isr2.c
index ce984e7..e7f5129 100644
--- a/gcc/testsuite/gcc.target/sh/torture/pragma-isr2.c
+++ b/gcc/testsuite/gcc.target/sh/torture/pragma-isr2.c
@@ -1,6 +1,5 @@
/* Check whether rte is generated only for an ISRs. */
/* { dg-do compile } */
-/* { dg-skip-if "" { "sh*-*-*" } { "-m5*" } { "" } } */
/* { dg-final { scan-assembler-times "rte" 1 } } */
#pragma interrupt
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [SH][committed] Remove SH5 support in compiler
2016-04-30 1:58 ` Oleg Endo
@ 2016-04-30 5:44 ` Oleg Endo
2016-04-30 9:22 ` Oleg Endo
0 siblings, 1 reply; 10+ messages in thread
From: Oleg Endo @ 2016-04-30 5:44 UTC (permalink / raw)
To: gcc-patches
[-- Attachment #1: Type: text/plain, Size: 1720 bytes --]
On Sat, 2016-04-30 at 10:58 +0900, Oleg Endo wrote:
> On Fri, 2016-04-29 at 23:11 +0900, Oleg Endo wrote:
> > On Fri, 2016-04-29 at 19:45 +0900, Oleg Endo wrote:
> > > On Thu, 2016-04-28 at 10:27 +0900, Oleg Endo wrote:
> > >
> > > > The removal of SH5 support from GCC has been announced here
> > > > https://gcc.gnu.org/ml/gcc/2015-08/msg00101.html
> > > >
> > > > The attached patch removes support for SH5 in the compiler back
> > > > end.
> > > > There are still some leftovers and new simplification
> > > > opportunities.
> > > > These will be addressed in later follow up patches.
> > > >
> > > > Tested on sh-elf with
> > > >
> > > > make -k check RUNTESTFLAGS="--target_board=sh-sim\{-m2/-ml,-m2/
> > > > -mb,
> > > > -m2a/-mb,-m4/-ml,-m4/-mb,-m4a/-ml,-m4a/-mb}"
> > >
> > > The attached patch removes some leftovers and reinstantes the
> > > divsf3
> > > expander pattern which got accidentally deleted by the previous
> > > patch.
> >
> > The attached patch removes SH5 support from libgcc.
> > Tested as above. Committed as r235640.
>
> The attached patch removes SH5 checks in the testsuite.
> Committed as r235673.
The attached patch removes some remaining superfluous TARGET_SH1
checks. Tested with
make -k check-gcc RUNTESTFLAGS="--target_board=sh-sim\{-m2/-ml,-m2/-mb,
-m2a/-mb,-m4/-ml,-m4/-mb,-m4a/-ml,-m4a/-mb}";
Committed as r235674.
Cheers,
Oleg
gcc/ChangeLog:
* config/sh/sh.c (register_sh_passes, sh_option_override,
sh_print_operand, prepare_move_operands,
sh_can_follow_jump): Remove TARGET_SH1 checks.
* config/sh/sh.h (TARGET_VARARGS_PRETEND_ARGS, VALID_REGISTER_P,
PROMOTE_MODE): Likewise.
* config/sh/sh.md (adddi3, addsi3, subdi3, subsi3, andsi3,
movdi): Likewise.
[-- Attachment #2: remove_sh64_sh5_gcc_6.patch --]
[-- Type: text/x-patch, Size: 9535 bytes --]
diff --git a/gcc/config/sh/sh.c b/gcc/config/sh/sh.c
index 3d9ce9d..b37d3ab 100644
--- a/gcc/config/sh/sh.c
+++ b/gcc/config/sh/sh.c
@@ -772,9 +772,6 @@ extern opt_pass* make_pass_sh_optimize_sett_clrt (gcc::context* ctx,
static void
register_sh_passes (void)
{
- if (!TARGET_SH1)
- return;
-
/* Running the sh_treg_combine pass after ce1 generates better code when
comparisons are combined and reg-reg moves are introduced, because
reg-reg moves will be eliminated afterwards. However, there are quite
@@ -848,36 +845,31 @@ sh_option_override (void)
if (!TARGET_SH3 && TARGET_USERMODE)
TARGET_USERMODE = false;
- if (TARGET_SH1)
+ if (! strcmp (sh_div_str, "call-div1"))
+ sh_div_strategy = SH_DIV_CALL_DIV1;
+ else if (! strcmp (sh_div_str, "call-fp") && TARGET_FPU_ANY)
+ sh_div_strategy = SH_DIV_CALL_FP;
+ else if (! strcmp (sh_div_str, "call-table") && TARGET_DYNSHIFT)
+ sh_div_strategy = SH_DIV_CALL_TABLE;
+ else
{
- if (! strcmp (sh_div_str, "call-div1"))
- sh_div_strategy = SH_DIV_CALL_DIV1;
- else if (! strcmp (sh_div_str, "call-fp")
- && (TARGET_FPU_DOUBLE || TARGET_FPU_SINGLE_ONLY
- || TARGET_FPU_ANY))
- sh_div_strategy = SH_DIV_CALL_FP;
- else if (! strcmp (sh_div_str, "call-table") && TARGET_DYNSHIFT)
+ /* Pick one that makes most sense for the target in general.
+ It is not much good to use different functions depending on -Os,
+ since then we'll end up with two different functions when some of
+ the code is compiled for size, and some for speed. */
+
+ /* SH4 tends to emphasize speed. */
+ if (TARGET_HARD_SH4)
sh_div_strategy = SH_DIV_CALL_TABLE;
+ /* These have their own way of doing things. */
+ else if (TARGET_SH2A)
+ sh_div_strategy = SH_DIV_INTRINSIC;
+ /* SH1 .. SH3 cores often go into small-footprint systems, so
+ default to the smallest implementation available. */
else
- /* Pick one that makes most sense for the target in general.
- It is not much good to use different functions depending
- on -Os, since then we'll end up with two different functions
- when some of the code is compiled for size, and some for
- speed. */
-
- /* SH4 tends to emphasize speed. */
- if (TARGET_HARD_SH4)
- sh_div_strategy = SH_DIV_CALL_TABLE;
- /* These have their own way of doing things. */
- else if (TARGET_SH2A)
- sh_div_strategy = SH_DIV_INTRINSIC;
- /* SH1 .. SH3 cores often go into small-footprint systems, so
- default to the smallest implementation available. */
- else
- sh_div_strategy = SH_DIV_CALL_DIV1;
+ sh_div_strategy = SH_DIV_CALL_DIV1;
}
- if (!TARGET_SH1)
- TARGET_PRETEND_CMOVE = 0;
+
if (sh_divsi3_libfunc[0])
; /* User supplied - leave it alone. */
else if (TARGET_DIVIDE_CALL_FP)
@@ -1443,8 +1435,7 @@ sh_print_operand (FILE *stream, rtx x, int code)
break;
default:
- if (TARGET_SH1)
- fputc ('#', stream);
+ fputc ('#', stream);
output_addr_const (stream, x);
break;
}
@@ -1618,8 +1609,7 @@ prepare_move_operands (rtx operands[], machine_mode mode)
of a library call to the target. Reject `st r0,@(rX,rY)' because
reload will fail to find a spill register for rX, since r0 is already
being used for the source. */
- else if (TARGET_SH1
- && refers_to_regno_p (R0_REG, operands[1])
+ else if (refers_to_regno_p (R0_REG, operands[1])
&& MEM_P (operands[0])
&& GET_CODE (XEXP (operands[0], 0)) == PLUS
&& REG_P (XEXP (XEXP (operands[0], 0), 1)))
@@ -1639,7 +1629,7 @@ prepare_move_operands (rtx operands[], machine_mode mode)
case. We can pre-allocate R0 for that index term to avoid
the issue. See PR target/66591. */
else if (sh_lra_p ()
- && TARGET_SH1 && ! TARGET_SH2A
+ && ! TARGET_SH2A
&& ((REG_P (operands[0]) && MEM_P (operands[1]))
|| (REG_P (operands[1]) && MEM_P (operands[0]))))
{
@@ -9590,8 +9580,7 @@ sh_can_follow_jump (const rtx_insn *branch1, const rtx_insn *branch2)
{
/* Don't follow if BRANCH2 is possible to be a jump crossing between
hot and cold partitions. */
- if (TARGET_SH1
- && flag_reorder_blocks_and_partition
+ if (flag_reorder_blocks_and_partition
&& simplejump_p (branch2)
&& CROSSING_JUMP_P (branch2))
return false;
diff --git a/gcc/config/sh/sh.h b/gcc/config/sh/sh.h
index 9f104f0..31d75e8 100644
--- a/gcc/config/sh/sh.h
+++ b/gcc/config/sh/sh.h
@@ -77,7 +77,7 @@ extern int code_for_indirect_jump_scratch;
/* This is not used by the SH2E calling convention */
#define TARGET_VARARGS_PRETEND_ARGS(FUN_DECL) \
- (TARGET_SH1 && ! TARGET_SH2E \
+ (! TARGET_SH2E \
&& ! (TARGET_HITACHI || sh_attr_renesas_p (FUN_DECL)))
#ifndef TARGET_CPU_DEFAULT
@@ -636,7 +636,7 @@ extern char sh_additional_register_names[ADDREGNAMES_SIZE] \
|| XD_REGISTER_P (REGNO) \
|| (REGNO) == AP_REG || (REGNO) == RAP_REG \
|| (REGNO) == FRAME_POINTER_REGNUM \
- || (TARGET_SH1 && (SPECIAL_REGISTER_P (REGNO) || (REGNO) == PR_REG)) \
+ || ((SPECIAL_REGISTER_P (REGNO) || (REGNO) == PR_REG)) \
|| (TARGET_SH2E && (REGNO) == FPUL_REG))
/* The mode that should be generally used to store a register by
@@ -1879,8 +1879,7 @@ extern int current_function_interrupt;
#define PROMOTE_MODE(MODE, UNSIGNEDP, TYPE) \
if (GET_MODE_CLASS (MODE) == MODE_INT \
&& GET_MODE_SIZE (MODE) < 4/* ! UNITS_PER_WORD */)\
- (UNSIGNEDP) = ((MODE) == SImode ? 0 : (UNSIGNEDP)), \
- (MODE) = (TARGET_SH1 ? SImode : DImode);
+ (UNSIGNEDP) = ((MODE) == SImode ? 0 : (UNSIGNEDP)), (MODE) = SImode;
#define MAX_FIXED_MODE_SIZE (64)
diff --git a/gcc/config/sh/sh.md b/gcc/config/sh/sh.md
index ef90303..ad29426 100644
--- a/gcc/config/sh/sh.md
+++ b/gcc/config/sh/sh.md
@@ -1529,12 +1529,9 @@
(match_operand:DI 2 "arith_operand")))]
""
{
- if (TARGET_SH1)
- {
- operands[2] = force_reg (DImode, operands[2]);
- emit_insn (gen_adddi3_compact (operands[0], operands[1], operands[2]));
- DONE;
- }
+ operands[2] = force_reg (DImode, operands[2]);
+ emit_insn (gen_adddi3_compact (operands[0], operands[1], operands[2]));
+ DONE;
})
(define_insn_and_split "adddi3_compact"
@@ -1780,7 +1777,7 @@
(match_operand:SI 2 "arith_or_int_operand")))]
""
{
- if (TARGET_SH1 && !arith_operand (operands[2], SImode))
+ if (!arith_operand (operands[2], SImode))
{
if (!sh_lra_p () || reg_overlap_mentioned_p (operands[0], operands[1]))
{
@@ -1935,12 +1932,9 @@
(match_operand:DI 2 "arith_reg_operand" "")))]
""
{
- if (TARGET_SH1)
- {
- operands[1] = force_reg (DImode, operands[1]);
- emit_insn (gen_subdi3_compact (operands[0], operands[1], operands[2]));
- DONE;
- }
+ operands[1] = force_reg (DImode, operands[1]);
+ emit_insn (gen_subdi3_compact (operands[0], operands[1], operands[2]));
+ DONE;
})
(define_insn_and_split "subdi3_compact"
@@ -2165,7 +2159,7 @@
(match_operand:SI 2 "arith_reg_operand" "")))]
""
{
- if (TARGET_SH1 && CONST_INT_P (operands[1]))
+ if (CONST_INT_P (operands[1]))
{
emit_insn (gen_negsi2 (operands[0], operands[2]));
emit_insn (gen_addsi3 (operands[0], operands[0], operands[1]));
@@ -2840,20 +2834,18 @@
Ideally the splitter of *andsi_compact would be enough, if redundant
zero extensions were detected after the combine pass, which does not
happen at the moment. */
- if (TARGET_SH1)
+
+ if (satisfies_constraint_Jmb (operands[2]))
{
- if (satisfies_constraint_Jmb (operands[2]))
- {
- emit_insn (gen_zero_extendqisi2 (operands[0],
- gen_lowpart (QImode, operands[1])));
- DONE;
- }
- else if (satisfies_constraint_Jmw (operands[2]))
- {
- emit_insn (gen_zero_extendhisi2 (operands[0],
- gen_lowpart (HImode, operands[1])));
- DONE;
- }
+ emit_insn (gen_zero_extendqisi2 (operands[0],
+ gen_lowpart (QImode, operands[1])));
+ DONE;
+ }
+ else if (satisfies_constraint_Jmw (operands[2]))
+ {
+ emit_insn (gen_zero_extendhisi2 (operands[0],
+ gen_lowpart (HImode, operands[1])));
+ DONE;
}
})
@@ -5565,23 +5557,19 @@
""
{
prepare_move_operands (operands, DImode);
- if (TARGET_SH1)
- {
- /* When the dest operand is (R0, R1) register pair, split it to
- two movsi of which dest is R1 and R0 so as to lower R0-register
- pressure on the first movsi. Apply only for simple source not
- to make complex rtl here. */
- if (REG_P (operands[0])
- && REGNO (operands[0]) == R0_REG
- && REG_P (operands[1])
- && REGNO (operands[1]) >= FIRST_PSEUDO_REGISTER)
- {
- emit_insn (gen_movsi (gen_rtx_REG (SImode, R1_REG),
- gen_rtx_SUBREG (SImode, operands[1], 4)));
- emit_insn (gen_movsi (gen_rtx_REG (SImode, R0_REG),
- gen_rtx_SUBREG (SImode, operands[1], 0)));
- DONE;
- }
+
+ /* When the dest operand is (R0, R1) register pair, split it to
+ two movsi of which dest is R1 and R0 so as to lower R0-register
+ pressure on the first movsi. Apply only for simple source not
+ to make complex rtl here. */
+ if (REG_P (operands[0]) && REGNO (operands[0]) == R0_REG
+ && REG_P (operands[1]) && REGNO (operands[1]) >= FIRST_PSEUDO_REGISTER)
+ {
+ emit_insn (gen_movsi (gen_rtx_REG (SImode, R1_REG),
+ gen_rtx_SUBREG (SImode, operands[1], 4)));
+ emit_insn (gen_movsi (gen_rtx_REG (SImode, R0_REG),
+ gen_rtx_SUBREG (SImode, operands[1], 0)));
+ DONE;
}
})
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [SH][committed] Remove SH5 support in compiler
2016-04-30 5:44 ` Oleg Endo
@ 2016-04-30 9:22 ` Oleg Endo
2016-04-30 9:39 ` Joseph Myers
0 siblings, 1 reply; 10+ messages in thread
From: Oleg Endo @ 2016-04-30 9:22 UTC (permalink / raw)
To: gcc-patches
[-- Attachment #1: Type: text/plain, Size: 2220 bytes --]
On Sat, 2016-04-30 at 14:44 +0900, Oleg Endo wrote:
> On Sat, 2016-04-30 at 10:58 +0900, Oleg Endo wrote:
> > On Fri, 2016-04-29 at 23:11 +0900, Oleg Endo wrote:
> > > On Fri, 2016-04-29 at 19:45 +0900, Oleg Endo wrote:
> > > > On Thu, 2016-04-28 at 10:27 +0900, Oleg Endo wrote:
> > > >
> > > > > The removal of SH5 support from GCC has been announced here
> > > > > https://gcc.gnu.org/ml/gcc/2015-08/msg00101.html
> > > > >
> > > > > The attached patch removes support for SH5 in the compiler
> > > > > back
> > > > > end.
> > > > > There are still some leftovers and new simplification
> > > > > opportunities.
> > > > > These will be addressed in later follow up patches.
> > > > >
> > > > > Tested on sh-elf with
> > > > >
> > > > > make -k check RUNTESTFLAGS="--target_board=sh-sim\{-m2/-ml,
> > > > > -m2/
> > > > > -mb,
> > > > > -m2a/-mb,-m4/-ml,-m4/-mb,-m4a/-ml,-m4a/-mb}"
> > > >
> > > > The attached patch removes some leftovers and reinstantes the
> > > > divsf3
> > > > expander pattern which got accidentally deleted by the previous
> > > > patch.
> > >
> > > The attached patch removes SH5 support from libgcc.
> > > Tested as above. Committed as r235640.
> >
> > The attached patch removes SH5 checks in the testsuite.
> > Committed as r235673.
>
> The attached patch removes some remaining superfluous TARGET_SH1
> checks. Tested with
The attached patch finally removes SH5 support from the various
configure machineries.
Tested with
make -k check-gcc RUNTESTFLAGS="--target_board=sh-sim\{-m2/-ml,-m2/-mb,
-m2a/-mb,-m4/-ml,-m4/-mb,-m4a/-ml,-m4a/-mb}"
Committed as r235676.
Cheers,
Oleg
ChangeLog:
/
* config.guess: Remove SH5 support.
* config.sub: Likewise.
* configure: Likewise.
* configure.ac: Likewise.
config/
* picflag.m4: Remove SH5 support.
gcc/
* config/sh/t-sh: Remove SH5 support.
* config.gcc: Likewise.
* configure: Likewise.
contrib/
* compare-all-tests: Remove SH5 support.
* config-list.mk: Likewise.
libada/
* configure: Remove SH5 support.
libgcc/
* config.host: Remove SH5 support.
* configure: Likewise.
libiberty/
* configure: Remove SH5 support.
libjava/
* classpath/config.guess: Remove SH5 support.
* classpath/config.sub: Likewise.
[-- Attachment #2: remove_sh64_sh5_config_7.patch --]
[-- Type: text/x-patch, Size: 16558 bytes --]
diff --git a/config.guess b/config.guess
index dcd5149..6396977 100755
--- a/config.guess
+++ b/config.guess
@@ -177,7 +177,6 @@ case "${UNAME_MACHINE}:${UNAME_SYSTEM}:${UNAME_RELEASE}:${UNAME_VERSION}" in
arm*) machine=arm-unknown ;;
sh3el) machine=shl-unknown ;;
sh3eb) machine=sh-unknown ;;
- sh5el) machine=sh5le-unknown ;;
earmv*)
arch=`echo ${UNAME_MACHINE_ARCH} | sed -e 's,^e\(armv[0-9]\).*$,\1,'`
endian=`echo ${UNAME_MACHINE_ARCH} | sed -ne 's,^.*\(eb\)$,\1,p'`
@@ -1028,9 +1027,6 @@ EOF
s390:Linux:*:* | s390x:Linux:*:*)
echo ${UNAME_MACHINE}-ibm-linux-${LIBC}
exit ;;
- sh64*:Linux:*:*)
- echo ${UNAME_MACHINE}-unknown-linux-${LIBC}
- exit ;;
sh*:Linux:*:*)
echo ${UNAME_MACHINE}-unknown-linux-${LIBC}
exit ;;
diff --git a/config.sub b/config.sub
index da6d1b6..1b4b975 100755
--- a/config.sub
+++ b/config.sub
@@ -306,7 +306,6 @@ case $basic_machine in
| rl78 | rx \
| score \
| sh | sh[1234] | sh[24]a | sh[24]aeb | sh[23]e | sh[234]eb | sheb | shbe | shle | sh[1234]le | sh3ele \
- | sh64 | sh64le \
| sparc | sparc64 | sparc64b | sparc64v | sparc86x | sparclet | sparclite \
| sparcv8 | sparcv9 | sparcv9b | sparcv9v \
| spu \
@@ -432,7 +431,7 @@ case $basic_machine in
| riscv32-* | riscv64-* \
| rl78-* | romp-* | rs6000-* | rx-* \
| sh-* | sh[1234]-* | sh[24]a-* | sh[24]aeb-* | sh[23]e-* | sh[34]eb-* | sheb-* | shbe-* \
- | shle-* | sh[1234]le-* | sh3ele-* | sh64-* | sh64le-* \
+ | shle-* | sh[1234]le-* | sh3ele-* \
| sparc-* | sparc64-* | sparc64b-* | sparc64v-* | sparc86x-* | sparclet-* \
| sparclite-* \
| sparcv8-* | sparcv9-* | sparcv9b-* | sparcv9v-* | sv1-* | sx*-* \
@@ -1094,12 +1093,6 @@ case $basic_machine in
basic_machine=sh-hitachi
os=-hms
;;
- sh5el)
- basic_machine=sh5le-unknown
- ;;
- sh64)
- basic_machine=sh64-unknown
- ;;
sparclite-wrs | simso-wrs)
basic_machine=sparclite-wrs
os=-vxworks
diff --git a/config/picflag.m4 b/config/picflag.m4
index 2f5b972..e0fa343 100644
--- a/config/picflag.m4
+++ b/config/picflag.m4
@@ -61,8 +61,7 @@ case "${$2}" in
$1=-fpic
;;
# FIXME: Simplify to sh*-*-netbsd*?
- sh-*-netbsdelf* | shl*-*-netbsdelf* | sh5-*-netbsd* | sh5l*-*-netbsd* | \
- sh64-*-netbsd* | sh64l*-*-netbsd*)
+ sh-*-netbsdelf* | shl*-*-netbsdelf*)
$1=-fpic
;;
# Default to -fPIC unless specified otherwise.
diff --git a/configure b/configure
index 35f231e..31f1dd6 100755
--- a/configure
+++ b/configure
@@ -3446,8 +3446,6 @@ case "${target}" in
;;
sh-*-* | sh[34]*-*-*)
;;
- sh64-*-* | sh5*-*-*)
- ;;
sparc*-*-*)
;;
x86_64-*-*)
@@ -3946,7 +3944,7 @@ case "${target}" in
or1k*-*-*)
noconfigdirs="$noconfigdirs gdb"
;;
- sh-*-* | sh64-*-*)
+ sh-*-*)
case "${target}" in
sh*-*-elf)
;;
diff --git a/configure.ac b/configure.ac
index 74bf58a..017b5a0 100644
--- a/configure.ac
+++ b/configure.ac
@@ -782,8 +782,6 @@ case "${target}" in
;;
sh-*-* | sh[[34]]*-*-*)
;;
- sh64-*-* | sh5*-*-*)
- ;;
sparc*-*-*)
;;
x86_64-*-*)
@@ -1282,7 +1280,7 @@ case "${target}" in
or1k*-*-*)
noconfigdirs="$noconfigdirs gdb"
;;
- sh-*-* | sh64-*-*)
+ sh-*-*)
case "${target}" in
sh*-*-elf)
;;
diff --git a/contrib/compare-all-tests b/contrib/compare-all-tests
index 444e3b5..7851a1b 100644
--- a/contrib/compare-all-tests
+++ b/contrib/compare-all-tests
@@ -31,11 +31,10 @@ mn10300_opts='-mam33 -mam33-2'
pa_opts='-march=2.0 -march=1.0 -march=1.1'
ppc_opts='-m32 -m64'
s390_opts='-m31 -m31/-mzarch -m64'
-sh64_opts='-m5-32media -m5-32media-nofpu -m5-64media -m5-64media-nofpu -m5-compact -m5-compact-nofpu'
sh_opts='-m3 -m3e -m4 -m4a -m4al -m4/-mieee -m1 -m1/-mno-cbranchdi -m2a -m2a/-mieee -m2e -m2e/-mieee'
sparc_opts='-mcpu=v8/-m32 -mcpu=v9/-m32 -m64'
-all_targets='alpha arm avr bfin cris fr30 frv h8300 ia64 iq2000 m32c m32r m68k mcore mips mmix mn10300 pa pdp11 ppc sh sh64 sparc spu v850 vax xstormy16 xtensa' # e500
+all_targets='alpha arm avr bfin cris fr30 frv h8300 ia64 iq2000 m32c m32r m68k mcore mips mmix mn10300 pa pdp11 ppc sh sparc spu v850 vax xstormy16 xtensa' # e500
test_one_file ()
{
diff --git a/contrib/config-list.mk b/contrib/config-list.mk
index 6a83a84..8210352 100644
--- a/contrib/config-list.mk
+++ b/contrib/config-list.mk
@@ -63,8 +63,8 @@ LIST = aarch64-elf aarch64-linux-gnu aarch64-rtems \
powerpcle-eabisim powerpcle-eabi rs6000-ibm-aix4.3 rs6000-ibm-aix5.1.0 \
rs6000-ibm-aix5.2.0 rs6000-ibm-aix5.3.0 rs6000-ibm-aix6.0 \
rl78-elf rx-elf s390-linux-gnu s390x-linux-gnu s390x-ibm-tpf sh-elf \
- shle-linux sh-netbsdelf sh-superh-elf sh5el-netbsd sh64-netbsd sh64-linux \
- sh64-elfOPT-with-newlib sh-rtems sh-wrs-vxworks sparc-elf \
+ shle-linux sh-netbsdelf sh-superh-elf \
+ sh-rtems sh-wrs-vxworks sparc-elf \
sparc-leon-elf sparc-rtems sparc-linux-gnu \
sparc-leon3-linux-gnuOPT-enable-target=all sparc-netbsdelf \
sparc64-sun-solaris2.10OPT-with-gnu-ldOPT-with-gnu-asOPT-enable-threads=posix \
diff --git a/gcc/config.gcc b/gcc/config.gcc
index f66e48c..4e98df7 100644
--- a/gcc/config.gcc
+++ b/gcc/config.gcc
@@ -2617,16 +2617,15 @@ s390x-ibm-tpf*)
;;
sh-*-elf* | sh[12346l]*-*-elf* | \
sh-*-linux* | sh[2346lbe]*-*-linux* | \
- sh-*-netbsdelf* | shl*-*-netbsdelf* | sh5-*-netbsd* | sh5l*-*-netbsd* | \
- sh64-*-netbsd* | sh64l*-*-netbsd*)
+ sh-*-netbsdelf* | shl*-*-netbsdelf*)
tmake_file="${tmake_file} sh/t-sh sh/t-elf"
if test x${with_endian} = x; then
case ${target} in
sh[1234]*be-*-* | sh[1234]*eb-*-*) with_endian=big ;;
shbe-*-* | sheb-*-*) with_endian=big,little ;;
sh[1234]l* | sh[34]*-*-linux*) with_endian=little ;;
- shl* | sh64l* | sh*-*-linux* | \
- sh5l* | sh-superh-elf) with_endian=little,big ;;
+ shl* | sh*-*-linux* | \
+ sh-superh-elf) with_endian=little,big ;;
sh[1234]*-*-*) with_endian=big ;;
*) with_endian=big,little ;;
esac
@@ -2670,37 +2669,14 @@ sh-*-elf* | sh[12346l]*-*-elf* | \
tm_file="${tm_file} sh/embed-elf.h" ;;
esac
case ${target} in
- sh5*-*-netbsd*)
- # SHmedia, 32-bit ABI
- tmake_file="${tmake_file} sh/t-sh64"
- ;;
- sh64*-netbsd*)
- # SHmedia, 64-bit ABI
- tmake_file="${tmake_file} sh/t-sh64 sh/t-netbsd-sh5-64"
- ;;
*-*-netbsd)
;;
- sh64*-*-linux*)
- tmake_file="${tmake_file} sh/t-sh64"
- tm_file="${tm_file} sh/sh64.h"
- extra_headers="shmedia.h ushmedia.h sshmedia.h"
- ;;
- sh64*)
- tmake_file="${tmake_file} sh/t-sh64"
- tm_file="${tm_file} sh/sh64.h"
- if test x$with_newlib = xyes; then
- tm_file="${tm_file} newlib-stdint.h"
- fi
- extra_headers="shmedia.h ushmedia.h sshmedia.h"
- ;;
*-*-elf*)
tm_file="${tm_file} newlib-stdint.h"
;;
esac
# sed el/eb endian suffixes away to avoid confusion with sh[23]e
case `echo ${target} | sed 's/e[lb]-/-/'` in
- sh64*-*-netbsd*) sh_cpu_target=sh5-64media ;;
- sh64* | sh5*-*-netbsd*) sh_cpu_target=sh5-32media ;;
sh4a_single_only*) sh_cpu_target=sh4a-single-only ;;
sh4a_single*) sh_cpu_target=sh4a-single ;;
sh4a_nofpu*) sh_cpu_target=sh4a-nofpu ;;
@@ -2723,7 +2699,6 @@ sh-*-elf* | sh[12346l]*-*-elf* | \
# did the user say --without-fp ?
if test x$with_fp = xno; then
case ${sh_cpu_target} in
- sh5-*media) sh_cpu_target=${sh_cpu_target}-nofpu ;;
sh4al | sh1) ;;
sh4a* ) sh_cpu_target=sh4a-nofpu ;;
sh4*) sh_cpu_target=sh4-nofpu ;;
@@ -2736,8 +2711,6 @@ sh-*-elf* | sh[12346l]*-*-elf* | \
fi
sh_cpu_default="`echo $with_cpu|sed s/^m/sh/|tr A-Z_ a-z-`"
case $sh_cpu_default in
- sh5-64media-nofpu | sh5-64media | \
- sh5-32media-nofpu | sh5-32media | sh5-compact-nofpu | sh5-compact | \
sh2a-single-only | sh2a-single | sh2a-nofpu | sh2a | \
sh4a-single-only | sh4a-single | sh4a-nofpu | sh4a | sh4al | \
sh4-single-only | sh4-single | sh4-nofpu | sh4 | sh4-300 | \
@@ -2748,9 +2721,7 @@ sh-*-elf* | sh[12346l]*-*-elf* | \
sh_multilibs=${with_multilib_list}
if test "$sh_multilibs" = "default" ; then
case ${target} in
- sh64-superh-linux* | \
sh[1234]*) sh_multilibs=${sh_cpu_target} ;;
- sh64* | sh5*) sh_multilibs=m5-32media,m5-32media-nofpu,m5-compact,m5-compact-nofpu,m5-64media,m5-64media-nofpu ;;
sh-superh-*) sh_multilibs=m4,m4-single,m4-single-only,m4-nofpu ;;
sh*-*-linux*) sh_multilibs=m1,m2,m2a,m3e,m4 ;;
sh*-*-netbsd*) sh_multilibs=m3,m3e,m4 ;;
@@ -2769,10 +2740,7 @@ sh-*-elf* | sh[12346l]*-*-elf* | \
m1 | m2 | m2e | m3 | m3e | \
m4 | m4-single | m4-single-only | m4-nofpu | m4-300 |\
m4a | m4a-single | m4a-single-only | m4a-nofpu | m4al | \
- m2a | m2a-single | m2a-single-only | m2a-nofpu | \
- m5-64media | m5-64media-nofpu | \
- m5-32media | m5-32media-nofpu | \
- m5-compact | m5-compact-nofpu)
+ m2a | m2a-single | m2a-single-only | m2a-nofpu)
# TM_MULTILIB_CONFIG is used by t-sh for the non-endian multilib definition
# It is passed to MULTIILIB_OPTIONS verbatim.
TM_MULTILIB_CONFIG="${TM_MULTILIB_CONFIG}/${sh_multilib}"
@@ -2789,7 +2757,7 @@ sh-*-elf* | sh[12346l]*-*-elf* | \
done
TM_MULTILIB_CONFIG=`echo $TM_MULTILIB_CONFIG | sed 's:^/::'`
if test x${enable_incomplete_targets} = xyes ; then
- tm_defines="$tm_defines SUPPORT_SH1=1 SUPPORT_SH2E=1 SUPPORT_SH4=1 SUPPORT_SH4_SINGLE=1 SUPPORT_SH2A=1 SUPPORT_SH2A_SINGLE=1 SUPPORT_SH5_32MEDIA=1 SUPPORT_SH5_32MEDIA_NOFPU=1 SUPPORT_SH5_64MEDIA=1 SUPPORT_SH5_64MEDIA_NOFPU=1"
+ tm_defines="$tm_defines SUPPORT_SH1=1 SUPPORT_SH2E=1 SUPPORT_SH4=1 SUPPORT_SH4_SINGLE=1 SUPPORT_SH2A=1 SUPPORT_SH2A_SINGLE=1"
fi
tm_file="$tm_file ./sysroot-suffix.h"
tmake_file="$tmake_file t-sysroot-suffix"
diff --git a/gcc/config/sh/t-sh b/gcc/config/sh/t-sh
index 348cc0b..7446c8e 100644
--- a/gcc/config/sh/t-sh
+++ b/gcc/config/sh/t-sh
@@ -50,9 +50,7 @@ MULTILIB_MATCHES = $(shell \
m2e,m3e,m4-single-only,m4-100-single-only,m4-200-single-only,m4-300-single-only,m4a-single-only \
m2a-single,m2a-single-only \
m4-single,m4-100-single,m4-200-single,m4-300-single,m4a-single \
- m4,m4-100,m4-200,m4-300,m4a \
- m5-32media,m5-compact,m5-32media \
- m5-32media-nofpu,m5-compact-nofpu,m5-32media-nofpu; do \
+ m4,m4-100,m4-200,m4-300,m4a; do \
subst= ; \
for lib in `echo $$abi|tr , ' '` ; do \
if test "`echo $$multilibs|sed s/$$lib//`" != "$$multilibs"; then \
@@ -89,13 +87,7 @@ MULTILIB_OSDIRNAMES = \
m4a-single-only=!m4a-single-only $(OTHER_ENDIAN)/m4a-single-only=!$(OTHER_ENDIAN)/m4a-single-only \
m4a-single=!m4a-single $(OTHER_ENDIAN)/m4a-single=!$(OTHER_ENDIAN)/m4a-single \
m4a=!m4a $(OTHER_ENDIAN)/m4a=!$(OTHER_ENDIAN)/m4a \
- m4al=!m4al $(OTHER_ENDIAN)/m4al=!$(OTHER_ENDIAN)/m4al \
- m5-32media=!m5-32media $(OTHER_ENDIAN)/m5-32media=!$(OTHER_ENDIAN)/m5-32media \
- m5-32media-nofpu=!m5-32media-nofpu $(OTHER_ENDIAN)/m5-32media-nofpu=!$(OTHER_ENDIAN)/m5-32media-nofpu \
- m5-compact=!m5-compact $(OTHER_ENDIAN)/m5-compact=!$(OTHER_ENDIAN)/m5-compact \
- m5-compact-nofpu=!m5-compact-nofpu $(OTHER_ENDIAN)/m5-compact-nofpu=!$(OTHER_ENDIAN)/m5-compact-nofpu \
- m5-64media=!m5-64media $(OTHER_ENDIAN)/m5-64media=!$(OTHER_ENDIAN)/m5-64media \
- m5-64media-nofpu=!m5-64media-nofpu $(OTHER_ENDIAN)/m5-64media-nofpu=!$(OTHER_ENDIAN)/m5-64media-nofpu
+ m4al=!m4al $(OTHER_ENDIAN)/m4al=!$(OTHER_ENDIAN)/m4al
$(out_object_file): gt-sh.h
gt-sh.h : s-gtype ; @true
diff --git a/gcc/configure b/gcc/configure
index 1c6e340..2e426ac 100755
--- a/gcc/configure
+++ b/gcc/configure
@@ -5060,8 +5060,7 @@ case "${target}" in
PICFLAG_FOR_TARGET=-fpic
;;
# FIXME: Simplify to sh*-*-netbsd*?
- sh-*-netbsdelf* | shl*-*-netbsdelf* | sh5-*-netbsd* | sh5l*-*-netbsd* | \
- sh64-*-netbsd* | sh64l*-*-netbsd*)
+ sh-*-netbsdelf* | shl*-*-netbsdelf*)
PICFLAG_FOR_TARGET=-fpic
;;
# Default to -fPIC unless specified otherwise.
diff --git a/libada/configure b/libada/configure
index 2296096..981bcdb 100755
--- a/libada/configure
+++ b/libada/configure
@@ -2878,8 +2878,7 @@ case "${host}" in
PICFLAG=-fpic
;;
# FIXME: Simplify to sh*-*-netbsd*?
- sh-*-netbsdelf* | shl*-*-netbsdelf* | sh5-*-netbsd* | sh5l*-*-netbsd* | \
- sh64-*-netbsd* | sh64l*-*-netbsd*)
+ sh-*-netbsdelf* | shl*-*-netbsdelf*)
PICFLAG=-fpic
;;
# Default to -fPIC unless specified otherwise.
diff --git a/libgcc/config.host b/libgcc/config.host
index b61a579..41a1897 100644
--- a/libgcc/config.host
+++ b/libgcc/config.host
@@ -1136,10 +1136,6 @@ sh-*-elf* | sh[12346l]*-*-elf*)
libic_invalidate_array_4-200.a \
libic_invalidate_array_4a.a \
libgcc-Os-4-200.a libgcc-4-300.a"
- case ${host} in sh64*-*-*)
- tmake_file="$tmake_file sh/t-sh64"
- ;;
- esac
case ${host} in
sh*-superh-elf)
tmake_file="$tmake_file sh/t-superh"
@@ -1149,20 +1145,11 @@ sh-*-elf* | sh[12346l]*-*-elf*)
;;
sh-*-linux* | sh[2346lbe]*-*-linux*)
tmake_file="${tmake_file} sh/t-sh t-slibgcc-libgcc sh/t-linux t-fdpbit"
- case ${host} in sh64*-*-linux*)
- tmake_file="$tmake_file sh/t-sh64"
- ;;
- esac
md_unwind_header=sh/linux-unwind.h
;;
-sh-*-netbsdelf* | shl*-*-netbsdelf* | sh5-*-netbsd* | sh5l*-*-netbsd* | \
- sh64-*-netbsd* | sh64l*-*-netbsd*)
+sh-*-netbsdelf* | shl*-*-netbsdelf*)
tmake_file="$tmake_file sh/t-sh sh/t-netbsd"
- case ${host} in
- sh5*-*-netbsd* | sh64*-netbsd*)
- tmake_file="$tmake_file sh/t-sh64"
- ;;
- esac
+
# NetBSD's C library includes a fast software FP library that
# has support for setting/setting the rounding mode, exception
# mask, etc. Therefore, we don't want to include software FP
diff --git a/libgcc/configure b/libgcc/configure
index e7d6c75..bf96aec 100644
--- a/libgcc/configure
+++ b/libgcc/configure
@@ -2355,8 +2355,7 @@ case "${host}" in
PICFLAG=-fpic
;;
# FIXME: Simplify to sh*-*-netbsd*?
- sh-*-netbsdelf* | shl*-*-netbsdelf* | sh5-*-netbsd* | sh5l*-*-netbsd* | \
- sh64-*-netbsd* | sh64l*-*-netbsd*)
+ sh-*-netbsdelf* | shl*-*-netbsdelf*)
PICFLAG=-fpic
;;
# Default to -fPIC unless specified otherwise.
diff --git a/libiberty/configure b/libiberty/configure
index bde78ff..0f8e9b9 100755
--- a/libiberty/configure
+++ b/libiberty/configure
@@ -5145,8 +5145,7 @@ case "${host}" in
PICFLAG=-fpic
;;
# FIXME: Simplify to sh*-*-netbsd*?
- sh-*-netbsdelf* | shl*-*-netbsdelf* | sh5-*-netbsd* | sh5l*-*-netbsd* | \
- sh64-*-netbsd* | sh64l*-*-netbsd*)
+ sh-*-netbsdelf* | shl*-*-netbsdelf*)
PICFLAG=-fpic
;;
# Default to -fPIC unless specified otherwise.
diff --git a/libjava/classpath/config.guess b/libjava/classpath/config.guess
index b02565c..f70fd60 100755
--- a/libjava/classpath/config.guess
+++ b/libjava/classpath/config.guess
@@ -162,7 +162,6 @@ case "${UNAME_MACHINE}:${UNAME_SYSTEM}:${UNAME_RELEASE}:${UNAME_VERSION}" in
arm*) machine=arm-unknown ;;
sh3el) machine=shl-unknown ;;
sh3eb) machine=sh-unknown ;;
- sh5el) machine=sh5le-unknown ;;
*) machine=${UNAME_MACHINE_ARCH}-unknown ;;
esac
# The Operating System including object format, if it has switched
@@ -968,9 +967,6 @@ EOF
s390:Linux:*:* | s390x:Linux:*:*)
echo ${UNAME_MACHINE}-ibm-linux
exit ;;
- sh64*:Linux:*:*)
- echo ${UNAME_MACHINE}-unknown-linux-gnu
- exit ;;
sh*:Linux:*:*)
echo ${UNAME_MACHINE}-unknown-linux-gnu
exit ;;
diff --git a/libjava/classpath/config.sub b/libjava/classpath/config.sub
index 59bb593..d728224 100755
--- a/libjava/classpath/config.sub
+++ b/libjava/classpath/config.sub
@@ -307,7 +307,6 @@ case $basic_machine in
| rl78 | rx \
| score \
| sh | sh[1234] | sh[24]a | sh[24]aeb | sh[23]e | sh[34]eb | sheb | shbe | shle | sh[1234]le | sh3ele \
- | sh64 | sh64le \
| sparc | sparc64 | sparc64b | sparc64v | sparc86x | sparclet | sparclite \
| sparcv8 | sparcv9 | sparcv9b | sparcv9v \
| spu \
@@ -421,7 +420,7 @@ case $basic_machine in
| pyramid-* \
| rl78-* | romp-* | rs6000-* | rx-* \
| sh-* | sh[1234]-* | sh[24]a-* | sh[24]aeb-* | sh[23]e-* | sh[34]eb-* | sheb-* | shbe-* \
- | shle-* | sh[1234]le-* | sh3ele-* | sh64-* | sh64le-* \
+ | shle-* | sh[1234]le-* | sh3ele-* \
| sparc-* | sparc64-* | sparc64b-* | sparc64v-* | sparc86x-* | sparclet-* \
| sparclite-* \
| sparcv8-* | sparcv9-* | sparcv9b-* | sparcv9v-* | sv1-* | sx?-* \
@@ -1064,12 +1063,6 @@ case $basic_machine in
basic_machine=sh-hitachi
os=-hms
;;
- sh5el)
- basic_machine=sh5le-unknown
- ;;
- sh64)
- basic_machine=sh64-unknown
- ;;
sparclite-wrs | simso-wrs)
basic_machine=sparclite-wrs
os=-vxworks
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [SH][committed] Remove SH5 support in compiler
2016-04-30 9:22 ` Oleg Endo
@ 2016-04-30 9:39 ` Joseph Myers
2016-04-30 11:02 ` Oleg Endo
0 siblings, 1 reply; 10+ messages in thread
From: Joseph Myers @ 2016-04-30 9:39 UTC (permalink / raw)
To: Oleg Endo; +Cc: gcc-patches
On Sat, 30 Apr 2016, Oleg Endo wrote:
> * config.guess: Remove SH5 support.
> * config.sub: Likewise.
Please revert. These files must come verbatim from config.git with no
local changes. If you persuade config-patches that SH5 support should be
removed there then you can import new, unmodified upstream files.
> * configure: Likewise.
For all the configure scripts listed, regeneration rather than manual
editing is appropriate. Please make sure the changes you committed are
identical to those from a proper regeneration with the right autoconf
version.
> * classpath/config.guess: Remove SH5 support.
> * classpath/config.sub: Likewise.
Again, please revert and keep these files identical to upstream.
--
Joseph S. Myers
joseph@codesourcery.com
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [SH][committed] Remove SH5 support in compiler
2016-04-30 9:39 ` Joseph Myers
@ 2016-04-30 11:02 ` Oleg Endo
2016-05-03 22:42 ` Eric Botcazou
0 siblings, 1 reply; 10+ messages in thread
From: Oleg Endo @ 2016-04-30 11:02 UTC (permalink / raw)
To: Joseph Myers; +Cc: gcc-patches
Joseph,
Thanks for keeping an eye on that.
On Sat, 2016-04-30 at 09:39 +0000, Joseph Myers wrote:
> On Sat, 30 Apr 2016, Oleg Endo wrote:
>
> > * config.guess: Remove SH5 support.
> > * config.sub: Likewise.
>
> Please revert. These files must come verbatim from config.git with
> no local changes. If you persuade config-patches that SH5 support
> should be removed there then you can import new, unmodified upstream
> files.
Done (r235677). I've sent the patch to config-patches.
>
> > * configure: Likewise.
>
> For all the configure scripts listed, regeneration rather than manual
> editing is appropriate. Please make sure the changes you committed
> are identical to those from a proper regeneration with the right
> autoconf version.
Did that. Looks there are no changes after regeneration.
Cheers,
Oleg
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [SH][committed] Remove SH5 support in compiler
2016-04-30 11:02 ` Oleg Endo
@ 2016-05-03 22:42 ` Eric Botcazou
2016-05-11 12:37 ` Oleg Endo
0 siblings, 1 reply; 10+ messages in thread
From: Eric Botcazou @ 2016-05-03 22:42 UTC (permalink / raw)
To: Oleg Endo; +Cc: gcc-patches, Joseph Myers
> Did that. Looks there are no changes after regeneration.
Not in the libada directory:
eric@polaris:~/svn/gcc/libada> svn info configure configure.ac
Path: configure
Name: configure
Working Copy Root Path: /home/eric/svn/gcc
URL: svn+ssh://gcc.gnu.org/svn/gcc/trunk/libada/configure
Relative URL: ^/trunk/libada/configure
Repository Root: svn+ssh://gcc.gnu.org/svn/gcc
Repository UUID: 138bc75d-0d04-0410-961f-82ee72b054a4
Revision: 235678
Node Kind: file
Schedule: normal
Last Changed Author: olegendo
Last Changed Rev: 235676
Last Changed Date: 2016-04-30 11:11:03 +0200 (Sat, 30 Apr 2016)
Text Last Updated: 2016-04-30 12:43:53 +0200 (Sat, 30 Apr 2016)
Checksum: 81a247fa3a0b075a9d5912fc76108ca80958bf4d
Path: configure.ac
Name: configure.ac
Working Copy Root Path: /home/eric/svn/gcc
URL: svn+ssh://gcc.gnu.org/svn/gcc/trunk/libada/configure.ac
Relative URL: ^/trunk/libada/configure.ac
Repository Root: svn+ssh://gcc.gnu.org/svn/gcc
Repository UUID: 138bc75d-0d04-0410-961f-82ee72b054a4
Revision: 235678
Node Kind: file
Schedule: normal
Last Changed Author: jakub
Last Changed Rev: 232055
Last Changed Date: 2016-01-04 15:30:50 +0100 (Mon, 04 Jan 2016)
Text Last Updated: 2016-01-06 08:00:38 +0100 (Wed, 06 Jan 2016)
Checksum: 33d89322bb3530f3c351968d9d127c6af002acf7
You cannot change any configure files without changing configure.ac.
--
Eric Botcazou
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [SH][committed] Remove SH5 support in compiler
2016-05-03 22:42 ` Eric Botcazou
@ 2016-05-11 12:37 ` Oleg Endo
0 siblings, 0 replies; 10+ messages in thread
From: Oleg Endo @ 2016-05-11 12:37 UTC (permalink / raw)
To: Eric Botcazou; +Cc: gcc-patches, Joseph Myers
On Wed, 2016-05-04 at 00:42 +0200, Eric Botcazou wrote:
> > Did that. Looks there are no changes after regeneration.
>
> Not in the libada directory:
>
> eric@polaris:~/svn/gcc/libada> svn info configure configure.ac
> Path: configure
> Name: configure
> Working Copy Root Path: /home/eric/svn/gcc
> URL: svn+ssh://gcc.gnu.org/svn/gcc/trunk/libada/configure
> Relative URL: ^/trunk/libada/configure
> Repository Root: svn+ssh://gcc.gnu.org/svn/gcc
> Repository UUID: 138bc75d-0d04-0410-961f-82ee72b054a4
> Revision: 235678
> Node Kind: file
> Schedule: normal
> Last Changed Author: olegendo
> Last Changed Rev: 235676
> Last Changed Date: 2016-04-30 11:11:03 +0200 (Sat, 30 Apr 2016)
> Text Last Updated: 2016-04-30 12:43:53 +0200 (Sat, 30 Apr 2016)
> Checksum: 81a247fa3a0b075a9d5912fc76108ca80958bf4d
>
> Path: configure.ac
> Name: configure.ac
> Working Copy Root Path: /home/eric/svn/gcc
> URL: svn+ssh://gcc.gnu.org/svn/gcc/trunk/libada/configure.ac
> Relative URL: ^/trunk/libada/configure.ac
> Repository Root: svn+ssh://gcc.gnu.org/svn/gcc
> Repository UUID: 138bc75d-0d04-0410-961f-82ee72b054a4
> Revision: 235678
> Node Kind: file
> Schedule: normal
> Last Changed Author: jakub
> Last Changed Rev: 232055
> Last Changed Date: 2016-01-04 15:30:50 +0100 (Mon, 04 Jan 2016)
> Text Last Updated: 2016-01-06 08:00:38 +0100 (Wed, 06 Jan 2016)
> Checksum: 33d89322bb3530f3c351968d9d127c6af002acf7
>
> You cannot change any configure files without changing configure.ac.
Ugh, sorry. Those pieces that I've changed manually are pulled from
the GNU config repo. At least that's what I understand. My proposed
changes to remove SH5 support in GNU config were rejected. I will
revert the corresponding changes in GCC.
Cheers,
Oleg
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2016-05-11 12:37 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-04-28 1:27 [SH][committed] Remove SH5 support in compiler Oleg Endo
2016-04-29 10:45 ` Oleg Endo
2016-04-29 14:11 ` Oleg Endo
2016-04-30 1:58 ` Oleg Endo
2016-04-30 5:44 ` Oleg Endo
2016-04-30 9:22 ` Oleg Endo
2016-04-30 9:39 ` Joseph Myers
2016-04-30 11:02 ` Oleg Endo
2016-05-03 22:42 ` Eric Botcazou
2016-05-11 12:37 ` Oleg Endo
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).