From: "Agus Ariffianto" <aariffianto@s.ee.itb.ac.id>
To: "Andrew Lunn" <andrew@lunn.ch>
Cc: "Mahmud Galela" <mgalela@vlsi.itb.ac.id>,
<ecos-discuss@ecos.sourceware.org>
Subject: Re: [ECOS] error: no memory region specified for loadable '.ram_vectors'
Date: Tue, 30 May 2006 13:02:00 -0000 [thread overview]
Message-ID: <043601c56517$c54d2e30$6c44cda7@aariffianto> (raw)
In-Reply-To: <20060530120216.GN2876@lunn.ch>
>> My questions are:
>>
>> 1. Why message: "...hello.bin": not in executable format: File format not
>> recognized." turn up?
>
>
> gdb wants the elf file, not the binary you produced.
>
>> 2. How to create 'the executable file'? I was successfully created ecos
>> bootable disk (run in PC, showing hello ecos). I enter command (in cygwin
>> environment):
>>
>> [cygwin-agus]$ dd conv=sync if=hello.bin of=/dev/fd0
>>
>> What should I do to produce the same executable (or bootable <?>)
>> file?
>
> How do you intend to get the image onto the system? Does it have a
> floppy and a BIOS to boot it? Are you going to burn it into an EEPROM?
> Do you have a JTAG interface to load the program into RAM?
>
> Andrew
Then I use target board (Alter Stratix S40). First of all I load LEON into
the board (via JTAG), then I load hello.out (via serial). Here is the
result:
Agus@aariffianto /opt/grmon-eval-1.1.3/win32/ecos/project-ecos
$ ../../grmon-eval.exe -u -uart COM8
GRMON LEON debug monitor v1.1.3 (evaluation version)
Copyright (C) 2004,2005 Gaisler Research - all rights reserved.
For latest updates, go to http://www.gaisler.com/
Comments or bug-reports to support@gaisler.com
This evaluation version will expire on 8/2/2006
try open device COM8
###opened device COM8
GRLIB plug&play not found, switching to LEON2 legacy mode
initialising ..........
detected frequency: 50 MHz
Component Vendor
LEON2 Memory Controller European Space Agency
LEON2 SPARC V8 processor European Space Agency
LEON2 Configuration register European Space Agency
LEON2 Timer Unit European Space Agency
LEON2 UART European Space Agency
LEON2 UART European Space Agency
LEON2 Interrupt Ctrl European Space Agency
LEON2 I/O port European Space Agency
AHB Debug UART Gaisler Research
LEON2 Debug Support Unit Gaisler Research
Use command 'info sys' to print a detailed report of attached cores
grmon> load hello.out
section: .rom_vectors at 0x40000000, size 4864 bytes
section: .text at 0x40001300, size 63996 bytes
section: .rodata at 0x40010cfc, size 804 bytes
section: .data at 0x40011020, size 1168 bytes
total size: 70832 bytes (30.7 kbit/s)
read 406 symbols
entry point: 0x40001300
grmon> run
IU in error mode (tt = 0x07)
400077bc d0026010 ld [%o1 + 0x10], %o0
grmon>
1. Is the error appear because of warning message which turn up when I
compile the source using ecos-configtool?
2. What should I do?
Thank you very much.
Regards,
Agus
--
Before posting, please read the FAQ: http://ecos.sourceware.org/fom/ecos
and search the list archive: http://ecos.sourceware.org/ml/ecos-discuss
next prev parent reply other threads:[~2006-05-30 13:02 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-05-29 9:20 Agus Ariffianto
2006-05-29 9:44 ` Andrew Lunn
2006-05-29 10:40 ` Agus Ariffianto
2006-05-29 12:20 ` Andrew Lunn
2006-05-30 4:00 ` Agus Ariffianto
2006-05-30 7:28 ` AW: " Ram Sudhir Tadavarthi
2006-05-30 7:38 ` Andrew Lunn
2006-05-30 11:49 ` Agus Ariffianto
2006-05-30 12:02 ` Andrew Lunn
2006-05-30 12:40 ` Agus Ariffianto
2006-05-30 12:59 ` Andrew Lunn
2006-05-30 13:02 ` Agus Ariffianto [this message]
2006-05-30 13:18 ` Andrew Lunn
2006-05-30 13:28 ` Agus Ariffianto
2006-06-13 9:31 ` [ECOS] error: no memory region specified for loadable '.ram_vectors' => Now it works Agus Ariffianto
2006-05-30 4:06 ` [ECOS] error: no memory region specified for loadable '.ram_vectors' Agus Ariffianto
2006-05-30 7:43 ` Andrew Lunn
2006-05-30 9:36 ` Agus Ariffianto
2006-05-30 11:19 ` Andrew Lunn
2006-05-29 9:38 Agus Ariffianto
2006-05-29 11:21 Agus Ariffianto
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='043601c56517$c54d2e30$6c44cda7@aariffianto' \
--to=aariffianto@s.ee.itb.ac.id \
--cc=andrew@lunn.ch \
--cc=ecos-discuss@ecos.sourceware.org \
--cc=mgalela@vlsi.itb.ac.id \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).