* [ECOS] To NavEcos
@ 2002-10-28 19:52 Vikram Mehta
2002-10-29 0:03 ` [ECOS] " NavEcos
0 siblings, 1 reply; 2+ messages in thread
From: Vikram Mehta @ 2002-10-28 19:52 UTC (permalink / raw)
To: NavEcos; +Cc: ecos-discuss
Hi NavEcos
Thanx a lot for ur response.
I was able to solve the problem. ( and I did not have to use an
oscilloscope . ha ha)
But Thanx again
On Mon, 28 Oct 2002 NavEcos wrote :
>On Saturday 26 October 2002 09:12 pm, Vikram Mehta wrote:
> > Hi NavEcos
> >
> > the baudrate I am using is 38400. THis is mentioned in the
> > Docmentations.Earlier I had tried at 9600 which is what I
>have
> > been using.
> > What baudrate shud I be using
> > And u have talked abt the cable connection. Kindly specify
>what
> > type of Cable connection I should use.
> > I am using the Cable sent along E7t. The cable specificaton
>given
> > along is
> > "signal ground, Rx, and Tx. Rx, and Tx not crossed over
> > (that is, it must be a straight-through cable). "
>
>I am no expert, but from what it sounds like you either have a
>bad cable or
>the wrong baudrate. I would simply try other baud rates with
>reboots in
>between.
>
>I once had a case where a serial cable failed to work in my
>laptop when the
>laptop was running off from the battery. Same sort of results.
>With the
>wrong baud rate you'll get garbage characters, and with a cable
>that has a
>high impedance the same sort of thing can happen.
>
>Of course, this may not be the problem at all, it's very
>difficult to debug a
>problem when you're not there, and I'm not. If it were me, I'd
>hook up an
>oscilloscope if I had to and debug by reading the bits. I'd also
>recompile
>the redboot code and make a modification to spit out a single
>character
>repeatedly.
>
>-Rich
__________________________________________________________
Give your Company an email address like
ravi @ ravi-exports.com. Sign up for Rediffmail Pro today!
Know more. http://www.rediffmailpro.com/signup/
--
Before posting, please read the FAQ: http://sources.redhat.com/fom/ecos
and search the list archive: http://sources.redhat.com/ml/ecos-discuss
^ permalink raw reply [flat|nested] 2+ messages in thread
* [ECOS] Re: To NavEcos
2002-10-28 19:52 [ECOS] To NavEcos Vikram Mehta
@ 2002-10-29 0:03 ` NavEcos
0 siblings, 0 replies; 2+ messages in thread
From: NavEcos @ 2002-10-29 0:03 UTC (permalink / raw)
To: Vikram Mehta; +Cc: ecos-discuss
Out of curiosity - what was the the problem?
Don't be embarassed if it was obvious, I once spent 3 days debugging a board
because I forgot to replace a jumper after I programmed the EEPROM.
-Rich
On Monday 28 October 2002 07:53 pm, Vikram Mehta wrote:
> Hi NavEcos
>
> Thanx a lot for ur response.
> I was able to solve the problem. ( and I did not have to use an
> oscilloscope . ha ha)
> But Thanx again
>
> On Mon, 28 Oct 2002 NavEcos wrote :
> >On Saturday 26 October 2002 09:12 pm, Vikram Mehta wrote:
> > > Hi NavEcos
> > >
> > > the baudrate I am using is 38400. THis is mentioned in the
> > > Docmentations.Earlier I had tried at 9600 which is what I
> >
> >have
> >
> > > been using.
> > > What baudrate shud I be using
> > > And u have talked abt the cable connection. Kindly specify
> >
> >what
> >
> > > type of Cable connection I should use.
> > > I am using the Cable sent along E7t. The cable specificaton
> >
> >given
> >
> > > along is
> > > "signal ground, Rx, and Tx. Rx, and Tx not crossed over
> > > (that is, it must be a straight-through cable). "
> >
> >I am no expert, but from what it sounds like you either have a
> >bad cable or
> >the wrong baudrate. I would simply try other baud rates with
> >reboots in
> >between.
> >
> >I once had a case where a serial cable failed to work in my
> >laptop when the
> >laptop was running off from the battery. Same sort of results.
> >With the
> >wrong baud rate you'll get garbage characters, and with a cable
> >that has a
> >high impedance the same sort of thing can happen.
> >
> >Of course, this may not be the problem at all, it's very
> >difficult to debug a
> >problem when you're not there, and I'm not. If it were me, I'd
> >hook up an
> >oscilloscope if I had to and debug by reading the bits. I'd also
> >recompile
> >the redboot code and make a modification to spit out a single
> >character
> >repeatedly.
> >
> >-Rich
>
> __________________________________________________________
> Give your Company an email address like
> ravi @ ravi-exports.com. Sign up for Rediffmail Pro today!
> Know more. http://www.rediffmailpro.com/signup/
--
Before posting, please read the FAQ: http://sources.redhat.com/fom/ecos
and search the list archive: http://sources.redhat.com/ml/ecos-discuss
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2002-10-29 8:03 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2002-10-28 19:52 [ECOS] To NavEcos Vikram Mehta
2002-10-29 0:03 ` [ECOS] " NavEcos
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).