* [ECOS] Configuration of static IP addresses @ 2001-01-08 5:32 Christian Plessl 2001-01-08 5:59 ` Jonathan Larmour 0 siblings, 1 reply; 7+ messages in thread From: Christian Plessl @ 2001-01-08 5:32 UTC (permalink / raw) To: ecos-discuss; +Cc: Thomas Meyer Hi Folks I'd like to configure eCos TCP/IP networking with fixed IP addresses. Could anybody please tell me, which configuration options in ecos.ecc I have to change. I've tried this some time ago without any problem, but now I can't manage it anymore.. strange.. Chris -- Christian Plessl <cplessl@ee.ethz.ch> ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [ECOS] Configuration of static IP addresses 2001-01-08 5:32 [ECOS] Configuration of static IP addresses Christian Plessl @ 2001-01-08 5:59 ` Jonathan Larmour 2001-01-08 14:45 ` Christian Plessl 0 siblings, 1 reply; 7+ messages in thread From: Jonathan Larmour @ 2001-01-08 5:59 UTC (permalink / raw) To: Christian Plessl; +Cc: ecos-discuss, Thomas Meyer Christian Plessl wrote: > > Hi Folks > > I'd like to configure eCos TCP/IP networking with fixed IP addresses. > Could anybody please tell me, which configuration options in ecos.ecc I > have to change. > > I've tried this some time ago without any problem, but now I can't manage > it anymore.. strange.. Search for CYGHWR_NET_DRIVER_ETH0_ADDRS_IP although you should remember to make sure an ethernet card has been enabled in your configuration. Jifl -- Red Hat, Rustat House, Clifton Road, Cambridge, UK. Tel: +44 (1223) 271062 Un cheval, pas du glue. Pas du cheval, beaucoup du glue. || Opinions==mine ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [ECOS] Configuration of static IP addresses 2001-01-08 5:59 ` Jonathan Larmour @ 2001-01-08 14:45 ` Christian Plessl 2001-01-08 14:59 ` Jonathan Larmour 2001-01-09 7:24 ` Bart Veer 0 siblings, 2 replies; 7+ messages in thread From: Christian Plessl @ 2001-01-08 14:45 UTC (permalink / raw) To: Jonathan Larmour; +Cc: ecos-discuss, Thomas Meyer >Search for CYGHWR_NET_DRIVER_ETH0_ADDRS_IP although you should remember to >make sure an ethernet card has been enabled in your configuration. That was what I tried, but I get just the following error message: C CYGHWR_NET_DRIVER_ETH0_SETUP, "requires" constraint not satisfied: 1 == CYGHWR_NET_DRIVER_ETH0_SETUP Unable to generate build tree, this configuration still contains conflicts. Either resolve the conflicts or use --ignore-errors I cannot figure out, how to resolve this conflict. Chris -- Christian Plessl <cplessl@ee.ethz.ch> ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [ECOS] Configuration of static IP addresses 2001-01-08 14:45 ` Christian Plessl @ 2001-01-08 14:59 ` Jonathan Larmour 2001-01-09 7:24 ` Bart Veer 1 sibling, 0 replies; 7+ messages in thread From: Jonathan Larmour @ 2001-01-08 14:59 UTC (permalink / raw) To: Christian Plessl; +Cc: ecos-discuss, Thomas Meyer Christian Plessl wrote: > > >Search for CYGHWR_NET_DRIVER_ETH0_ADDRS_IP although you should remember to > >make sure an ethernet card has been enabled in your configuration. > > That was what I tried, but I get just the following error message: > > C CYGHWR_NET_DRIVER_ETH0_SETUP, "requires" constraint not satisfied: 1 == > CYGHWR_NET_DRIVER_ETH0_SETUP > > Unable to generate build tree, this configuration still contains > conflicts. > Either resolve the conflicts or use --ignore-errors > > I cannot figure out, how to resolve this conflict. Did you actually enable CYGHWR_NET_DRIVER_ETH0_ADDRS i.e. user_value 1 ? It's an option too. Jifl -- Red Hat, Rustat House, Clifton Road, Cambridge, UK. Tel: +44 (1223) 271062 Un cheval, pas du glue. Pas du cheval, beaucoup du glue. || Opinions==mine ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [ECOS] Configuration of static IP addresses 2001-01-08 14:45 ` Christian Plessl 2001-01-08 14:59 ` Jonathan Larmour @ 2001-01-09 7:24 ` Bart Veer 2001-01-09 14:28 ` Christian Plessl 1 sibling, 1 reply; 7+ messages in thread From: Bart Veer @ 2001-01-09 7:24 UTC (permalink / raw) To: cplessl; +Cc: ecos-discuss >>>>> "Chris" == Christian Plessl <cplessl@ee.ethz.ch> writes: >> Search for CYGHWR_NET_DRIVER_ETH0_ADDRS_IP although you should >> remember to make sure an ethernet card has been enabled in your >> configuration. Chris> That was what I tried, but I get just the following error Chris> message: Chris> C CYGHWR_NET_DRIVER_ETH0_SETUP, "requires" constraint not satisfied: 1 == Chris> CYGHWR_NET_DRIVER_ETH0_SETUP Chris> Unable to generate build tree, this configuration still Chris> contains conflicts. Either resolve the conflicts or use Chris> --ignore-errors Chris> I cannot figure out, how to resolve this conflict. There are three configuration options that implement the way the IP address is determined: CYGHWR_NET_DRIVER_ETH0_MANUAL, BOOTP, and ADDRS. The default is BOOTP. Only one of these can be enabled, so you need to disable the default option BOOTP and then enable ADDRS. If you look at CYGHWR_NET_DRIVER_ETH0_SETUP where the problem is reported, you should see something like: cdl_interface CYGHWR_NET_DRIVER_ETH0_SETUP { # Implemented by CYGHWR_NET_DRIVER_ETH0_MANUAL, active, disabled # Implemented by CYGHWR_NET_DRIVER_ETH0_BOOTP, active, enabled # Implemented by CYGHWR_NET_DRIVER_ETH0_ADDRS, active, disabled ... } This lists all the relevant configuration options. Bart ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [ECOS] Configuration of static IP addresses 2001-01-09 7:24 ` Bart Veer @ 2001-01-09 14:28 ` Christian Plessl 2001-01-09 16:31 ` Jonathan Larmour 0 siblings, 1 reply; 7+ messages in thread From: Christian Plessl @ 2001-01-09 14:28 UTC (permalink / raw) To: bartv; +Cc: ecos-discuss >There are three configuration options that implement the way the IP >address is determined: CYGHWR_NET_DRIVER_ETH0_MANUAL, BOOTP, and >ADDRS. The default is BOOTP. Only one of these can be enabled, so you >need to disable the default option BOOTP and then enable ADDRS. > >If you look at CYGHWR_NET_DRIVER_ETH0_SETUP where the problem is >reported, you should see something like: > >cdl_interface CYGHWR_NET_DRIVER_ETH0_SETUP { > # Implemented by CYGHWR_NET_DRIVER_ETH0_MANUAL, active, disabled > # Implemented by CYGHWR_NET_DRIVER_ETH0_BOOTP, active, enabled > # Implemented by CYGHWR_NET_DRIVER_ETH0_ADDRS, active, disabled > ... >} > >This lists all the relevant configuration options. Now it works. I had to set all the following options CYGHWR_NET_DRIVER_ETH0_ADDRS => user_value 1 CYGHWR_NET_DRIVER_ETH0_ADDRS_IP => user_value 192.168.1.50 CYGPKG_NET_DHCP => user_value 0 CYGHWR_NET_DRIVER_ETH0_BOOTP => user_value 0 Thanks for your help. Chris -- Christian Plessl <cplessl@ee.ethz.ch> ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [ECOS] Configuration of static IP addresses 2001-01-09 14:28 ` Christian Plessl @ 2001-01-09 16:31 ` Jonathan Larmour 0 siblings, 0 replies; 7+ messages in thread From: Jonathan Larmour @ 2001-01-09 16:31 UTC (permalink / raw) To: Christian Plessl; +Cc: bartv, ecos-discuss Christian Plessl wrote: > > >There are three configuration options that implement the way the IP > >address is determined: CYGHWR_NET_DRIVER_ETH0_MANUAL, BOOTP, and > >ADDRS. The default is BOOTP. Only one of these can be enabled, so you > >need to disable the default option BOOTP and then enable ADDRS. > > > >If you look at CYGHWR_NET_DRIVER_ETH0_SETUP where the problem is > >reported, you should see something like: > > > >cdl_interface CYGHWR_NET_DRIVER_ETH0_SETUP { > > # Implemented by CYGHWR_NET_DRIVER_ETH0_MANUAL, active, disabled > > # Implemented by CYGHWR_NET_DRIVER_ETH0_BOOTP, active, enabled > > # Implemented by CYGHWR_NET_DRIVER_ETH0_ADDRS, active, disabled > > ... > >} > > > >This lists all the relevant configuration options. > > Now it works. > > I had to set all the following options > > CYGHWR_NET_DRIVER_ETH0_ADDRS => user_value 1 > CYGHWR_NET_DRIVER_ETH0_ADDRS_IP => user_value 192.168.1.50 > CYGPKG_NET_DHCP => user_value 0 > CYGHWR_NET_DRIVER_ETH0_BOOTP => user_value 0 Purely FYI, you should have found that the latter two would have automatically got set to 0 if you used "ecosconfig resolve". Jifl -- Red Hat, Rustat House, Clifton Road, Cambridge, UK. Tel: +44 (1223) 271062 Un cheval, pas du glue. Pas du cheval, beaucoup du glue. || Opinions==mine ^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2001-01-09 16:31 UTC | newest] Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2001-01-08 5:32 [ECOS] Configuration of static IP addresses Christian Plessl 2001-01-08 5:59 ` Jonathan Larmour 2001-01-08 14:45 ` Christian Plessl 2001-01-08 14:59 ` Jonathan Larmour 2001-01-09 7:24 ` Bart Veer 2001-01-09 14:28 ` Christian Plessl 2001-01-09 16:31 ` Jonathan Larmour
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).