[ECOS] Can not connect to target x86 pc board

[ECOS] Can not connect to target x86 pc board

[John]

[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #1: Type: text/plain, Size: 2105 bytes --]

Hi all:

I Have used Configuration Tool to make a boot floppy
    (hardware --> i386 pc target ; package --> stubs)
and a eCos kernel without conflicts
    (hardware --> i386 pc target ; package --> default).

I insert the boot floppy into my target Intel PII pc board and use a cable to connect my host(COM1) and target(COM1).
After booting my target, the target monitor shows
    ++$T0508:e03b0000;04:e00f0000;#44
And then I use Configuration Tool
    Tools-->Run Tests-->Run
to test it and the following output message shows

*** 10:54:31 Run started
GNU gdb 5.0
Copyright 2000 Free Software Foundation, Inc.
GDB is free software, covered by the GNU General Public License, and you are
welcome to change it and/or distribute copies of it under certain conditions.
Type "show copying" to see the conditions.
There is absolutely no warranty for GDB.  Type "show warranty" for details.
This GDB was configured as "--host=i586-pc-cygwin --target=i386-elf"...
(gdb) set height 0
(gdb) set remotedebug 0
Warning: command 'set remotedebug' is deprecated.
Use 'set debug remote'.

(gdb) set remotebaud 38400
(gdb) target remote com1
Remote debugging using com1
Ignoring packet error, continuing...
Ignoring packet error, continuing...
Ignoring packet error, continuing...
Couldn't establish connection to remote target
Malformed response to offset query, timeout
(gdb) load
You can't do that when your target is `exec'
(gdb) break cyg_test_exit
Breakpoint 1 at 0x138df: file //d/PROGRA~1/REDHAT~1/eCos/packages/infra/v1_3_1/src/tcdiag.cxx, line 116.
(gdb) break cyg_assert_fail
Function "cyg_assert_fail" not defined.
(gdb) break cyg_test_init
Breakpoint 2 at 0x137fb: file //d/PROGRA~1/REDHAT~1/eCos/packages/infra/v1_3_1/src/tcdiag.cxx, line 62.
(gdb) cont
The program is not being run.

What's wrong?
Thanks in advance.

----
Á»¨­õ
John Hsieh
µo²{ªÌ°ê»ÚªÑ¥÷¦³­­¤½¥q
iMining Technology Co., Ltd.
john@imining.com.tw
TEL: 886-2-27235122
FAX: 886-2-27232287
www.imining.com.tw

RE: [ECOS] Can not connect to target x86 pc board

[John]

[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #1: Type: text/plain, Size: 3011 bytes --]

I have checked my pc board again
Both my pc boards of target and host just has 1 COM port
so I think it's hard to make mistakes

-----Original Message-----
From: Jitendra kanitkar [ mailto:Jitendrak@netbrahma.com ]
Sent: Monday, February 19, 2001 12:39 PM
To: 'John'
Cc: 'ecos-discuss@sources.redhat.com'
Subject: RE: [ECOS] Can not connect to target x86 pc board


HI,

Just check the cable and the port you are saying com1 is really  COM1.
Coz i did the same mistake. In my case it was com2, to which iconnected the
cable.

Thanks,
Jitendra.

> ----------
> From: 	John[SMTP:john@imining.com.tw]
> Sent: 	Monday, February 19, 2001 3:16 AM
> To: 	ecos-discuss@sources.redhat.com
> Subject: 	[ECOS] Can not connect to target x86 pc board
> 
> Hi all:
> 
> I Have used Configuration Tool to make a boot floppy
>     (hardware --> i386 pc target ; package --> stubs)
> and a eCos kernel without conflicts
>     (hardware --> i386 pc target ; package --> default).
> 
> I insert the boot floppy into my target Intel PII pc board and use a cable
> to connect my host(COM1) and target(COM1).
> After booting my target, the target monitor shows
>     ++$T0508:e03b0000;04:e00f0000;#44
> And then I use Configuration Tool
>     Tools-->Run Tests-->Run
> to test it and the following output message shows
> 
> *** 10:54:31 Run started
> GNU gdb 5.0
> Copyright 2000 Free Software Foundation, Inc.
> GDB is free software, covered by the GNU General Public License, and you
> are
> welcome to change it and/or distribute copies of it under certain
> conditions.
> Type "show copying" to see the conditions.
> There is absolutely no warranty for GDB.  Type "show warranty" for
> details.
> This GDB was configured as "--host=i586-pc-cygwin --target=i386-elf"...
> (gdb) set height 0
> (gdb) set remotedebug 0
> Warning: command 'set remotedebug' is deprecated.
> Use 'set debug remote'.
> 
> (gdb) set remotebaud 38400
> (gdb) target remote com1
> Remote debugging using com1
> Ignoring packet error, continuing...
> Ignoring packet error, continuing...
> Ignoring packet error, continuing...
> Couldn't establish connection to remote target
> Malformed response to offset query, timeout
> (gdb) load
> You can't do that when your target is `exec'
> (gdb) break cyg_test_exit
> Breakpoint 1 at 0x138df: file
> //d/PROGRA~1/REDHAT~1/eCos/packages/infra/v1_3_1/src/tcdiag.cxx, line 116.
> (gdb) break cyg_assert_fail
> Function "cyg_assert_fail" not defined.
> (gdb) break cyg_test_init
> Breakpoint 2 at 0x137fb: file
> //d/PROGRA~1/REDHAT~1/eCos/packages/infra/v1_3_1/src/tcdiag.cxx, line 62.
> (gdb) cont
> The program is not being run.
> 
> What's wrong?
> Thanks in advance.
> 
> ----
> Á»¨­õ
> John Hsieh
> µo²{ªÌ°ê»ÚªÑ¥÷¦³­­¤½¥q
> iMining Technology Co., Ltd.
> john@imining.com.tw
> TEL: 886-2-27235122
> FAX: 886-2-27232287
> www.imining.com.tw
> 

RE: [ECOS] Can not connect to target x86 pc board

[Jitendra kanitkar]

[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #1: Type: text/plain, Size: 2554 bytes --]

HI,

Just check the cable and the port you are saying com1 is really  COM1.
Coz i did the same mistake. In my case it was com2, to which iconnected the
cable.

Thanks,
Jitendra.

> ----------
> From: 	John[SMTP:john@imining.com.tw]
> Sent: 	Monday, February 19, 2001 3:16 AM
> To: 	ecos-discuss@sources.redhat.com
> Subject: 	[ECOS] Can not connect to target x86 pc board
> 
> Hi all:
> 
> I Have used Configuration Tool to make a boot floppy
>     (hardware --> i386 pc target ; package --> stubs)
> and a eCos kernel without conflicts
>     (hardware --> i386 pc target ; package --> default).
> 
> I insert the boot floppy into my target Intel PII pc board and use a cable
> to connect my host(COM1) and target(COM1).
> After booting my target, the target monitor shows
>     ++$T0508:e03b0000;04:e00f0000;#44
> And then I use Configuration Tool
>     Tools-->Run Tests-->Run
> to test it and the following output message shows
> 
> *** 10:54:31 Run started
> GNU gdb 5.0
> Copyright 2000 Free Software Foundation, Inc.
> GDB is free software, covered by the GNU General Public License, and you
> are
> welcome to change it and/or distribute copies of it under certain
> conditions.
> Type "show copying" to see the conditions.
> There is absolutely no warranty for GDB.  Type "show warranty" for
> details.
> This GDB was configured as "--host=i586-pc-cygwin --target=i386-elf"...
> (gdb) set height 0
> (gdb) set remotedebug 0
> Warning: command 'set remotedebug' is deprecated.
> Use 'set debug remote'.
> 
> (gdb) set remotebaud 38400
> (gdb) target remote com1
> Remote debugging using com1
> Ignoring packet error, continuing...
> Ignoring packet error, continuing...
> Ignoring packet error, continuing...
> Couldn't establish connection to remote target
> Malformed response to offset query, timeout
> (gdb) load
> You can't do that when your target is `exec'
> (gdb) break cyg_test_exit
> Breakpoint 1 at 0x138df: file
> //d/PROGRA~1/REDHAT~1/eCos/packages/infra/v1_3_1/src/tcdiag.cxx, line 116.
> (gdb) break cyg_assert_fail
> Function "cyg_assert_fail" not defined.
> (gdb) break cyg_test_init
> Breakpoint 2 at 0x137fb: file
> //d/PROGRA~1/REDHAT~1/eCos/packages/infra/v1_3_1/src/tcdiag.cxx, line 62.
> (gdb) cont
> The program is not being run.
> 
> What's wrong?
> Thanks in advance.
> 
> ----
> Á»¨­õ
> John Hsieh
> µo²{ªÌ°ê»ÚªÑ¥÷¦³­­¤½¥q
> iMining Technology Co., Ltd.
> john@imining.com.tw
> TEL: 886-2-27235122
> FAX: 886-2-27232287
> www.imining.com.tw
>