* Re: Successful Build and Install
@ 1998-03-25 23:43 Per Bothner
1998-03-26 18:14 ` Joe Buck
0 siblings, 1 reply; 10+ messages in thread
From: Per Bothner @ 1998-03-25 23:43 UTC (permalink / raw)
To: egcs
> Thought I'd pass on the info you requested: successful build and
> install. Worked without a hitch.
Is this "request" still in egcs? Has it outlived its usefulness?
At least for linux?
--Per Bothner
Cygnus Solutions bothner@cygnus.com http://www.cygnus.com/~bothner
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Successful Build and Install
1998-03-25 23:43 Successful Build and Install Per Bothner
@ 1998-03-26 18:14 ` Joe Buck
1998-04-02 11:32 ` Jeffrey A Law
0 siblings, 1 reply; 10+ messages in thread
From: Joe Buck @ 1998-03-26 18:14 UTC (permalink / raw)
To: Per Bothner; +Cc: egcs
> > Thought I'd pass on the info you requested: successful build and
> > install. Worked without a hitch.
>
> Is this "request" still in egcs? Has it outlived its usefulness?
> At least for linux?
It seems that we would only want:
* reports of failures on systems we believe to work
* reports of successes *or* failures on systems we haven't tested.
So we should be telling folks something like: if you run X, Y, or Z,
let us know if the install fails or there are large numbers of test
failures. If you have something more exotic, we'd appreciate a report
if you build successfully. And the list can be dynamic: if we hadn't
verified, say, FreeBSD 2.2.6 but some user does, we can indicate that.
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Successful Build and Install
1998-04-02 11:32 ` Jeffrey A Law
@ 1998-04-02 11:32 ` Joe Buck
1998-04-04 14:20 ` Jeffrey A Law
0 siblings, 1 reply; 10+ messages in thread
From: Joe Buck @ 1998-04-02 11:32 UTC (permalink / raw)
To: law; +Cc: jbuck, bothner, egcs
I wrote:
> > It seems that we would only want:
> > * reports of failures on systems we believe to work
> > * reports of successes *or* failures on systems we haven't tested.
Jeff writes:
> This is probably the right general direction for minor releases.
>
> However at each major release it's probably useful to get these
> reports for all systems -- including those we regularly work on.
Just the same, I'd like to cut down on email volume. We can expect
the egcs user community to increase greatly with time. Do you want
every single egcs user on Linux to send a mail to everyone on the list,
saying essentially the same thing? You'll start to drive away developers.
People have other things they want to do with their lives than read egcs,
and if they try using filters they'll miss important messages (delete
all test results? what if some expose problems?).
Another alternative is to publish a summary of test results on platforms
that we have tried. We can then ask people to send in a report if their
results differ *and* they've checked a FAQ to make sure they haven't made
a common mistake. If we have no report for their system, we would use
whatever users send in.
> It's been my experience that as a developer I know how to build
> things dead cold. It's amazing what kinds of problems are exposed
> by folks that don't build compilers every day...
Exactly. That's why we need reports from people who get different
results. But we don't need reports from people who get the same results.
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Successful Build and Install
1998-03-26 18:14 ` Joe Buck
@ 1998-04-02 11:32 ` Jeffrey A Law
1998-04-02 11:32 ` Joe Buck
0 siblings, 1 reply; 10+ messages in thread
From: Jeffrey A Law @ 1998-04-02 11:32 UTC (permalink / raw)
To: Joe Buck; +Cc: Per Bothner, egcs
In message <199803261957.LAA15374@atrus.synopsys.com>you write:
> It seems that we would only want:
> * reports of failures on systems we believe to work
> * reports of successes *or* failures on systems we haven't tested.
>
> So we should be telling folks something like: if you run X, Y, or Z,
> let us know if the install fails or there are large numbers of test
> failures. If you have something more exotic, we'd appreciate a report
> if you build successfully. And the list can be dynamic: if we hadn't
> verified, say, FreeBSD 2.2.6 but some user does, we can indicate that.
This is probably the right general direction for minor releases.
However at each major release it's probably useful to get these
reports for all systems -- including those we regularly work on.
It's been my experience that as a developer I know how to build
things dead cold. It's amazing what kinds of problems are exposed
by folks that don't build compilers every day...
jeff
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: Successful Build and Install
1998-04-02 11:32 ` Joe Buck
@ 1998-04-04 14:20 ` Jeffrey A Law
0 siblings, 0 replies; 10+ messages in thread
From: Jeffrey A Law @ 1998-04-04 14:20 UTC (permalink / raw)
To: Joe Buck; +Cc: bothner, egcs
In message < 199803311735.JAA15334@atrus.synopsys.com >you write:
> I wrote:
>
> > > It seems that we would only want:
> > > * reports of failures on systems we believe to work
> > > * reports of successes *or* failures on systems we haven't tested.
>
> Jeff writes:
> > This is probably the right general direction for minor releases.
> >
> > However at each major release it's probably useful to get these
> > reports for all systems -- including those we regularly work on.
>
> Just the same, I'd like to cut down on email volume. We can expect
> the egcs user community to increase greatly with time. Do you want
> every single egcs user on Linux to send a mail to everyone on the list,
> saying essentially the same thing? You'll start to drive away developers.
> People have other things they want to do with their lives than read egcs,
> and if they try using filters they'll miss important messages (delete
> all test results? what if some expose problems?).
Actually, if you're looking that far into the future, the solution
is a web page :-) Have a little form that you can fill out to specify
what platform you built on, and maybe comments.
That info is then make available on another page -- the idea is to
cut down on the "was anyone able to build on xyz" kinds of questions.
In fact, if someone wants to contribute the html gunk to do this it
would be greatly appreciated. Note you can check out the web pages
via CVS these days :-)
> Another alternative is to publish a summary of test results on platforms
> that we have tried. We can then ask people to send in a report if their
> results differ *and* they've checked a FAQ to make sure they haven't made
> a common mistake. If we have no report for their system, we would use
> whatever users send in.
Similarly -- we'd make a set of "baseline" test results available for
releases on major platforms (I don't think it's worth the time for
snapshots). People could then compare their own with those on the
web.
jeff
^ permalink raw reply [flat|nested] 10+ messages in thread
* successful build and install
@ 2014-05-09 9:30 Jiří Vymazal
0 siblings, 0 replies; 10+ messages in thread
From: Jiří Vymazal @ 2014-05-09 9:30 UTC (permalink / raw)
To: gcc
Here is info according to installation document on your homepages:
_______________________________________________________
srcdir/config.guess:
x86_64-unknown-linux-gnu
gcc -v:
Using built-in specs.
COLLECT_GCC=./gcc
COLLECT_LTO_WRAPPER=/usr/local/libexec/gcc/x86_64-unknown-linux-gnu/4.9.0/lto-wrapper
Target: x86_64-unknown-linux-gnu
Configured with: ../src/gcc-4.9.0/configure --enable-thread=posix
--with-fpmath=sse --disable-bootstrap --enable-languages=c,c++
--disable-multilib
Thread model: posix
gcc version 4.9.0 (GCC)
uname --version:
uname (GNU coreutils) 8.20
Copyright (C) 2012 Free Software Foundation, Inc.
License GPLv3+: GNU GPL version 3 or later <http://gnu.org/licenses/gpl.html>.
This is free software: you are free to change and redistribute it.
There is NO WARRANTY, to the extent permitted by law.
/
Written by David MacKenzie.
uname -a:
Linux cyberspider-MintXfceVM 3.11.0-12-generic #19-Ubuntu SMP Wed Oct
9 16:20:46 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux
dpkg -l libc6:
Desired=Unknown/Install/Remove/Purge/Hold
| Status=Not/Inst/Conf-files/Unpacked/halF-conf/Half-inst/trig-aWait/Trig-pend
|/ Err?=(none)/Reinst-required (Status,Err: uppercase=bad)
||/ Name Version
Architecture Description
+++-====================================-=======================-=======================-=============================================================================
ii libc6:amd64 2.17-93ubuntu4 amd64
Embedded GNU C Library: Shared libraries
ii libc6:i386 2.17-93ubuntu4 i386
Embedded GNU C Library: Shared libraries
OS is running in virtualbox 4.3.8 with newest quest additions
(v4.2.16) installed, host is 64-bit Windows 8.1 Pro N,
hardware-assisted virtualization enabled (i7-3537U), 3D acceleration
enabled, virtual machine is given 4096MB RAM, 128MB video memory and 2
cores
Thank you very much, you are doing awesome work!
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: successful build and install
2002-05-24 10:21 Benjamin Collar
@ 2002-05-24 11:22 ` Janis Johnson
0 siblings, 0 replies; 10+ messages in thread
From: Janis Johnson @ 2002-05-24 11:22 UTC (permalink / raw)
To: Benjamin Collar; +Cc: gcc
On Fri, May 24, 2002 at 04:53:26PM +0200, Benjamin Collar wrote:
> Greetings,
>
> I've build and installed gcc 3.1 on the system detailed here:
>
> i686-pc-linux-gnu
> Reading specs from /usr/local/lib/gcc-lib/i686-pc-linux-gnu/3.1/specs
> Configured with: /usr/local/src/gcc-3.1/configure --prefix=/usr/local
> --enable-languages=c,c++
> Thread model: single
> gcc version 3.1
> SuSE Linux 7.3 (i386)
> 2.4.18-lkpc-4 (linux kernel patch collection, rc4)
> glibc-2.2.4-21
Thanks! Your message is linked from the GCC 3.1 build status list at
http://gcc.gnu.org/gcc-3.1/buildstat.html.
Janis
^ permalink raw reply [flat|nested] 10+ messages in thread
* successful build and install
@ 2002-05-24 10:21 Benjamin Collar
2002-05-24 11:22 ` Janis Johnson
0 siblings, 1 reply; 10+ messages in thread
From: Benjamin Collar @ 2002-05-24 10:21 UTC (permalink / raw)
To: gcc
Greetings,
I've build and installed gcc 3.1 on the system detailed here:
i686-pc-linux-gnu
Reading specs from /usr/local/lib/gcc-lib/i686-pc-linux-gnu/3.1/specs
Configured with: /usr/local/src/gcc-3.1/configure --prefix=/usr/local
--enable-languages=c,c++
Thread model: single
gcc version 3.1
SuSE Linux 7.3 (i386)
2.4.18-lkpc-4 (linux kernel patch collection, rc4)
glibc-2.2.4-21
^ permalink raw reply [flat|nested] 10+ messages in thread
* Successful Build and Install
@ 1998-08-17 23:32 S. Colin Leister
0 siblings, 0 replies; 10+ messages in thread
From: S. Colin Leister @ 1998-08-17 23:32 UTC (permalink / raw)
To: egcs
[-- Attachment #1: Type: text/plain, Size: 17 bytes --]
Version: 1.0.3a
[-- Attachment #2: config.guess --]
[-- Type: text/x-shellscript, Size: 24803 bytes --]
#! /bin/sh
# Attempt to guess a canonical system name.
# Copyright (C) 1992, 93, 94, 95, 96, 1997 Free Software Foundation, Inc.
#
# This file is free software; you can redistribute it and/or modify it
# under the terms of the GNU General Public License as published by
# the Free Software Foundation; either version 2 of the License, or
# (at your option) any later version.
#
# This program is distributed in the hope that it will be useful, but
# WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
# General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
#
# As a special exception to the GNU General Public License, if you
# distribute this file as part of a program that contains a
# configuration script generated by Autoconf, you may include it under
# the same distribution terms that you use for the rest of that program.
# Written by Per Bothner <bothner@cygnus.com>.
# The master version of this file is at the FSF in /home/gd/gnu/lib.
#
# This script attempts to guess a canonical system name similar to
# config.sub. If it succeeds, it prints the system name on stdout, and
# exits with 0. Otherwise, it exits with 1.
#
# The plan is that this can be called by configure scripts if you
# don't specify an explicit system type (host/target name).
#
# Only a few systems have been added to this list; please add others
# (but try to keep the structure clean).
#
# This is needed to find uname on a Pyramid OSx when run in the BSD universe.
# (ghazi@noc.rutgers.edu 8/24/94.)
if (test -f /.attbin/uname) >/dev/null 2>&1 ; then
PATH=$PATH:/.attbin ; export PATH
fi
UNAME_MACHINE=`(uname -m) 2>/dev/null` || UNAME_MACHINE=unknown
UNAME_RELEASE=`(uname -r) 2>/dev/null` || UNAME_RELEASE=unknown
UNAME_SYSTEM=`(uname -s) 2>/dev/null` || UNAME_SYSTEM=unknown
UNAME_VERSION=`(uname -v) 2>/dev/null` || UNAME_VERSION=unknown
trap 'rm -f dummy.c dummy.o dummy; exit 1' 1 2 15
# Note: order is significant - the case branches are not exclusive.
case "${UNAME_MACHINE}:${UNAME_SYSTEM}:${UNAME_RELEASE}:${UNAME_VERSION}" in
alpha:OSF1:*:*)
if test $UNAME_RELEASE = "V4.0"; then
UNAME_RELEASE=`/usr/sbin/sizer -v | awk '{print $3}'`
fi
# A Vn.n version is a released version.
# A Tn.n version is a released field test version.
# A Xn.n version is an unreleased experimental baselevel.
# 1.2 uses "1.2" for uname -r.
cat <<EOF >dummy.s
.globl main
.ent main
main:
.frame \$30,0,\$26,0
.prologue 0
.long 0x47e03d80 # implver $0
lda \$2,259
.long 0x47e20c21 # amask $2,$1
srl \$1,8,\$2
sll \$2,2,\$2
sll \$0,3,\$0
addl \$1,\$0,\$0
addl \$2,\$0,\$0
ret \$31,(\$26),1
.end main
EOF
${CC-cc} dummy.s -o dummy 2>/dev/null
if test "$?" = 0 ; then
./dummy
case "$?" in
7)
UNAME_MACHINE="alpha"
;;
15)
UNAME_MACHINE="alphaev5"
;;
14)
UNAME_MACHINE="alphaev56"
;;
10)
UNAME_MACHINE="alphapca56"
;;
16)
UNAME_MACHINE="alphaev6"
;;
esac
fi
rm -f dummy.s dummy
echo ${UNAME_MACHINE}-dec-osf`echo ${UNAME_RELEASE} | sed -e 's/^[VTX]//' | tr [[A-Z]] [[a-z]]`
exit 0 ;;
21064:Windows_NT:50:3)
echo alpha-dec-winnt3.5
exit 0 ;;
Amiga*:UNIX_System_V:4.0:*)
echo m68k-cbm-sysv4
exit 0;;
amiga:NetBSD:*:*)
echo m68k-cbm-netbsd${UNAME_RELEASE}
exit 0 ;;
amiga:OpenBSD:*:*)
echo m68k-unknown-openbsd${UNAME_RELEASE}
exit 0 ;;
arc64:OpenBSD:*:*)
echo mips64el-unknown-openbsd${UNAME_RELEASE}
exit 0 ;;
arc:OpenBSD:*:*)
echo mipsel-unknown-openbsd${UNAME_RELEASE}
exit 0 ;;
hkmips:OpenBSD:*:*)
echo mips-unknown-openbsd${UNAME_RELEASE}
exit 0 ;;
pmax:OpenBSD:*:*)
echo mipsel-unknown-openbsd${UNAME_RELEASE}
exit 0 ;;
sgi:OpenBSD:*:*)
echo mips-unknown-openbsd${UNAME_RELEASE}
exit 0 ;;
wgrisc:OpenBSD:*:*)
echo mipsel-unknown-openbsd${UNAME_RELEASE}
exit 0 ;;
arm:RISC*:1.[012]*:*|arm:riscix:1.[012]*:*)
echo arm-acorn-riscix${UNAME_RELEASE}
exit 0;;
arm32:NetBSD:*:*)
echo arm-unknown-netbsd`echo ${UNAME_RELEASE}|sed -e 's/[-_].*/\./'`
exit 0 ;;
SR2?01:HI-UX/MPP:*:*)
echo hppa1.1-hitachi-hiuxmpp
exit 0;;
Pyramid*:OSx*:*:*|MIS*:OSx*:*:*)
# akee@wpdis03.wpafb.af.mil (Earle F. Ake) contributed MIS and NILE.
if test "`(/bin/universe) 2>/dev/null`" = att ; then
echo pyramid-pyramid-sysv3
else
echo pyramid-pyramid-bsd
fi
exit 0 ;;
NILE:*:*:dcosx)
echo pyramid-pyramid-svr4
exit 0 ;;
sun4*:SunOS:5.*:* | tadpole*:SunOS:5.*:*)
echo sparc-sun-solaris2`echo ${UNAME_RELEASE}|sed -e 's/[^.]*//'`
exit 0 ;;
i86pc:SunOS:5.*:*)
echo i386-pc-solaris2`echo ${UNAME_RELEASE}|sed -e 's/[^.]*//'`
exit 0 ;;
sun4*:SunOS:6*:*)
# According to config.sub, this is the proper way to canonicalize
# SunOS6. Hard to guess exactly what SunOS6 will be like, but
# it's likely to be more like Solaris than SunOS4.
echo sparc-sun-solaris3`echo ${UNAME_RELEASE}|sed -e 's/[^.]*//'`
exit 0 ;;
sun4*:SunOS:*:*)
case "`/usr/bin/arch -k`" in
Series*|S4*)
UNAME_RELEASE=`uname -v`
;;
esac
# Japanese Language versions have a version number like `4.1.3-JL'.
echo sparc-sun-sunos`echo ${UNAME_RELEASE}|sed -e 's/-/_/'`
exit 0 ;;
sun3*:SunOS:*:*)
echo m68k-sun-sunos${UNAME_RELEASE}
exit 0 ;;
sun*:*:4.2BSD:*)
UNAME_RELEASE=`(head -1 /etc/motd | awk '{print substr($5,1,3)}') 2>/dev/null`
test "x${UNAME_RELEASE}" = "x" && UNAME_RELEASE=3
case "`/bin/arch`" in
sun3)
echo m68k-sun-sunos${UNAME_RELEASE}
;;
sun4)
echo sparc-sun-sunos${UNAME_RELEASE}
;;
esac
exit 0 ;;
aushp:SunOS:*:*)
echo sparc-auspex-sunos${UNAME_RELEASE}
exit 0 ;;
atari*:NetBSD:*:*)
echo m68k-atari-netbsd${UNAME_RELEASE}
exit 0 ;;
atari*:OpenBSD:*:*)
echo m68k-unknown-openbsd${UNAME_RELEASE}
exit 0 ;;
sun3*:NetBSD:*:*)
echo m68k-sun-netbsd${UNAME_RELEASE}
exit 0 ;;
sun3*:OpenBSD:*:*)
echo m68k-unknown-openbsd${UNAME_RELEASE}
exit 0 ;;
mac68k:NetBSD:*:*)
echo m68k-apple-netbsd${UNAME_RELEASE}
exit 0 ;;
mac68k:OpenBSD:*:*)
echo m68k-unknown-openbsd${UNAME_RELEASE}
exit 0 ;;
mvme68k:OpenBSD:*:*)
echo m68k-unknown-openbsd${UNAME_RELEASE}
exit 0 ;;
mvme88k:OpenBSD:*:*)
echo m88k-unknown-openbsd${UNAME_RELEASE}
exit 0 ;;
powerpc:machten:*:*)
echo powerpc-apple-machten${UNAME_RELEASE}
exit 0 ;;
RISC*:Mach:*:*)
echo mips-dec-mach_bsd4.3
exit 0 ;;
RISC*:ULTRIX:*:*)
echo mips-dec-ultrix${UNAME_RELEASE}
exit 0 ;;
VAX*:ULTRIX*:*:*)
echo vax-dec-ultrix${UNAME_RELEASE}
exit 0 ;;
2020:CLIX:*:*)
echo clipper-intergraph-clix${UNAME_RELEASE}
exit 0 ;;
mips:*:*:UMIPS | mips:*:*:RISCos)
sed 's/^ //' << EOF >dummy.c
int main (argc, argv) int argc; char **argv; {
#if defined (host_mips) && defined (MIPSEB)
#if defined (SYSTYPE_SYSV)
printf ("mips-mips-riscos%ssysv\n", argv[1]); exit (0);
#endif
#if defined (SYSTYPE_SVR4)
printf ("mips-mips-riscos%ssvr4\n", argv[1]); exit (0);
#endif
#if defined (SYSTYPE_BSD43) || defined(SYSTYPE_BSD)
printf ("mips-mips-riscos%sbsd\n", argv[1]); exit (0);
#endif
#endif
exit (-1);
}
EOF
${CC-cc} dummy.c -o dummy \
&& ./dummy `echo "${UNAME_RELEASE}" | sed -n 's/\([0-9]*\).*/\1/p'` \
&& rm dummy.c dummy && exit 0
rm -f dummy.c dummy
echo mips-mips-riscos${UNAME_RELEASE}
exit 0 ;;
Night_Hawk:Power_UNIX:*:*)
echo powerpc-harris-powerunix
exit 0 ;;
m88k:CX/UX:7*:*)
echo m88k-harris-cxux7
exit 0 ;;
m88k:*:4*:R4*)
echo m88k-motorola-sysv4
exit 0 ;;
m88k:*:3*:R3*)
echo m88k-motorola-sysv3
exit 0 ;;
AViiON:dgux:*:*)
# DG/UX returns AViiON for all architectures
UNAME_PROCESSOR=`/usr/bin/uname -p`
if [ $UNAME_PROCESSOR = mc88100 -o $UNAME_PROCESSOR = mc88110 ] ; then
if [ ${TARGET_BINARY_INTERFACE}x = m88kdguxelfx \
-o ${TARGET_BINARY_INTERFACE}x = x ] ; then
echo m88k-dg-dgux${UNAME_RELEASE}
else
echo m88k-dg-dguxbcs${UNAME_RELEASE}
fi
else echo i586-dg-dgux${UNAME_RELEASE}
fi
exit 0 ;;
M88*:DolphinOS:*:*) # DolphinOS (SVR3)
echo m88k-dolphin-sysv3
exit 0 ;;
M88*:*:R3*:*)
# Delta 88k system running SVR3
echo m88k-motorola-sysv3
exit 0 ;;
XD88*:*:*:*) # Tektronix XD88 system running UTekV (SVR3)
echo m88k-tektronix-sysv3
exit 0 ;;
Tek43[0-9][0-9]:UTek:*:*) # Tektronix 4300 system running UTek (BSD)
echo m68k-tektronix-bsd
exit 0 ;;
*:IRIX*:*:*)
echo mips-sgi-irix`echo ${UNAME_RELEASE}|sed -e 's/-/_/g'`
exit 0 ;;
????????:AIX?:[12].1:2) # AIX 2.2.1 or AIX 2.1.1 is RT/PC AIX.
echo romp-ibm-aix # uname -m gives an 8 hex-code CPU id
exit 0 ;; # Note that: echo "'`uname -s`'" gives 'AIX '
i?86:AIX:*:*)
echo i386-ibm-aix
exit 0 ;;
*:AIX:2:3)
if grep bos325 /usr/include/stdio.h >/dev/null 2>&1; then
sed 's/^ //' << EOF >dummy.c
#include <sys/systemcfg.h>
main()
{
if (!__power_pc())
exit(1);
puts("powerpc-ibm-aix3.2.5");
exit(0);
}
EOF
${CC-cc} dummy.c -o dummy && ./dummy && rm dummy.c dummy && exit 0
rm -f dummy.c dummy
echo rs6000-ibm-aix3.2.5
elif grep bos324 /usr/include/stdio.h >/dev/null 2>&1; then
echo rs6000-ibm-aix3.2.4
else
echo rs6000-ibm-aix3.2
fi
exit 0 ;;
*:AIX:*:4)
if /usr/sbin/lsattr -EHl proc0 | grep POWER >/dev/null 2>&1; then
IBM_ARCH=rs6000
else
IBM_ARCH=powerpc
fi
if [ -x /usr/bin/oslevel ] ; then
IBM_REV=`/usr/bin/oslevel`
else
IBM_REV=4.${UNAME_RELEASE}
fi
echo ${IBM_ARCH}-ibm-aix${IBM_REV}
exit 0 ;;
*:AIX:*:*)
echo rs6000-ibm-aix
exit 0 ;;
ibmrt:4.4BSD:*|romp-ibm:BSD:*)
echo romp-ibm-bsd4.4
exit 0 ;;
ibmrt:*BSD:*|romp-ibm:BSD:*) # covers RT/PC NetBSD and
echo romp-ibm-bsd${UNAME_RELEASE} # 4.3 with uname added to
exit 0 ;; # report: romp-ibm BSD 4.3
*:BOSX:*:*)
echo rs6000-bull-bosx
exit 0 ;;
DPX/2?00:B.O.S.:*:*)
echo m68k-bull-sysv3
exit 0 ;;
9000/[34]??:4.3bsd:1.*:*)
echo m68k-hp-bsd
exit 0 ;;
hp300:4.4BSD:*:* | 9000/[34]??:4.3bsd:2.*:*)
echo m68k-hp-bsd4.4
exit 0 ;;
9000/[3478]??:HP-UX:*:*)
case "${UNAME_MACHINE}" in
9000/31? ) HP_ARCH=m68000 ;;
9000/[34]?? ) HP_ARCH=m68k ;;
9000/7?? | 9000/8?[1679] ) HP_ARCH=hppa1.1 ;;
9000/8?? ) HP_ARCH=hppa1.0 ;;
esac
HPUX_REV=`echo ${UNAME_RELEASE}|sed -e 's/[^.]*.[0B]*//'`
echo ${HP_ARCH}-hp-hpux${HPUX_REV}
exit 0 ;;
3050*:HI-UX:*:*)
sed 's/^ //' << EOF >dummy.c
#include <unistd.h>
int
main ()
{
long cpu = sysconf (_SC_CPU_VERSION);
/* The order matters, because CPU_IS_HP_MC68K erroneously returns
true for CPU_PA_RISC1_0. CPU_IS_PA_RISC returns correct
results, however. */
if (CPU_IS_PA_RISC (cpu))
{
switch (cpu)
{
case CPU_PA_RISC1_0: puts ("hppa1.0-hitachi-hiuxwe2"); break;
case CPU_PA_RISC1_1: puts ("hppa1.1-hitachi-hiuxwe2"); break;
case CPU_PA_RISC2_0: puts ("hppa2.0-hitachi-hiuxwe2"); break;
default: puts ("hppa-hitachi-hiuxwe2"); break;
}
}
else if (CPU_IS_HP_MC68K (cpu))
puts ("m68k-hitachi-hiuxwe2");
else puts ("unknown-hitachi-hiuxwe2");
exit (0);
}
EOF
${CC-cc} dummy.c -o dummy && ./dummy && rm dummy.c dummy && exit 0
rm -f dummy.c dummy
echo unknown-hitachi-hiuxwe2
exit 0 ;;
9000/7??:4.3bsd:*:* | 9000/8?[79]:4.3bsd:*:* )
echo hppa1.1-hp-bsd
exit 0 ;;
9000/8??:4.3bsd:*:*)
echo hppa1.0-hp-bsd
exit 0 ;;
hp7??:OSF1:*:* | hp8?[79]:OSF1:*:* )
echo hppa1.1-hp-osf
exit 0 ;;
hp8??:OSF1:*:*)
echo hppa1.0-hp-osf
exit 0 ;;
i?86:OSF1:*:*)
if [ -x /usr/sbin/sysversion ] ; then
echo ${UNAME_MACHINE}-unknown-osf1mk
else
echo ${UNAME_MACHINE}-unknown-osf1
fi
exit 0 ;;
parisc*:Lites*:*:*)
echo hppa1.1-hp-lites
exit 0 ;;
C1*:ConvexOS:*:* | convex:ConvexOS:C1*:*)
echo c1-convex-bsd
exit 0 ;;
C2*:ConvexOS:*:* | convex:ConvexOS:C2*:*)
if getsysinfo -f scalar_acc
then echo c32-convex-bsd
else echo c2-convex-bsd
fi
exit 0 ;;
C34*:ConvexOS:*:* | convex:ConvexOS:C34*:*)
echo c34-convex-bsd
exit 0 ;;
C38*:ConvexOS:*:* | convex:ConvexOS:C38*:*)
echo c38-convex-bsd
exit 0 ;;
C4*:ConvexOS:*:* | convex:ConvexOS:C4*:*)
echo c4-convex-bsd
exit 0 ;;
CRAY*X-MP:*:*:*)
echo xmp-cray-unicos
exit 0 ;;
CRAY*Y-MP:*:*:*)
echo ymp-cray-unicos${UNAME_RELEASE}
exit 0 ;;
CRAY*[A-Z]90:*:*:*)
echo ${UNAME_MACHINE}-cray-unicos${UNAME_RELEASE} \
| sed -e 's/CRAY.*\([A-Z]90\)/\1/' \
-e y/ABCDEFGHIJKLMNOPQRSTUVWXYZ/abcdefghijklmnopqrstuvwxyz/
exit 0 ;;
CRAY*TS:*:*:*)
echo t90-cray-unicos${UNAME_RELEASE}
exit 0 ;;
CRAY-2:*:*:*)
echo cray2-cray-unicos
exit 0 ;;
F300:UNIX_System_V:*:*)
FUJITSU_SYS=`uname -p | tr [A-Z] [a-z] | sed -e 's/\///'`
FUJITSU_REL=`echo ${UNAME_RELEASE} | sed -e 's/ /_/'`
echo "f300-fujitsu-${FUJITSU_SYS}${FUJITSU_REL}"
exit 0 ;;
F301:UNIX_System_V:*:*)
echo f301-fujitsu-uxpv`echo $UNAME_RELEASE | sed 's/ .*//'`
exit 0 ;;
hp3[0-9][05]:NetBSD:*:*)
echo m68k-hp-netbsd${UNAME_RELEASE}
exit 0 ;;
hp300:OpenBSD:*:*)
echo m68k-unknown-openbsd${UNAME_RELEASE}
exit 0 ;;
i?86:BSD/386:*:* | *:BSD/OS:*:*)
echo ${UNAME_MACHINE}-pc-bsdi${UNAME_RELEASE}
exit 0 ;;
*:FreeBSD:*:*)
echo ${UNAME_MACHINE}-unknown-freebsd`echo ${UNAME_RELEASE}|sed -e 's/[-(].*//'`
exit 0 ;;
*:NetBSD:*:*)
echo ${UNAME_MACHINE}-unknown-netbsd`echo ${UNAME_RELEASE}|sed -e 's/[-_].*/\./'`
exit 0 ;;
*:OpenBSD:*:*)
echo ${UNAME_MACHINE}-unknown-openbsd`echo ${UNAME_RELEASE}|sed -e 's/[-_].*/\./'`
exit 0 ;;
i*:CYGWIN*:*)
echo i386-pc-cygwin32
exit 0 ;;
i*:MINGW*:*)
echo i386-pc-mingw32
exit 0 ;;
p*:CYGWIN*:*)
echo powerpcle-unknown-cygwin32
exit 0 ;;
prep*:SunOS:5.*:*)
echo powerpcle-unknown-solaris2`echo ${UNAME_RELEASE}|sed -e 's/[^.]*//'`
exit 0 ;;
*:GNU:*:*)
echo `echo ${UNAME_MACHINE}|sed -e 's,[-/].*$,,'`-unknown-gnu`echo ${UNAME_RELEASE}|sed -e 's,/.*$,,'`
exit 0 ;;
*:Linux:*:*)
# The BFD linker knows what the default object file format is, so
# first see if it will tell us.
ld_help_string=`ld --help 2>&1`
ld_supported_emulations=`echo $ld_help_string \
| sed -ne '/supported emulations:/!d
s/[ ][ ]*/ /g
s/.*supported emulations: *//
s/ .*//
p'`
case "$ld_supported_emulations" in
i?86linux) echo "${UNAME_MACHINE}-pc-linux-gnuaout" ; exit 0 ;;
i?86coff) echo "${UNAME_MACHINE}-pc-linux-gnucoff" ; exit 0 ;;
sparclinux) echo "${UNAME_MACHINE}-unknown-linux-gnuaout" ; exit 0 ;;
m68klinux) echo "${UNAME_MACHINE}-unknown-linux-gnuaout" ; exit 0 ;;
elf32ppc)
# Determine Lib Version
cat >dummy.c <<EOF
#include <features.h>
#if defined(__GLIBC__)
extern char __libc_version[];
extern char __libc_release[];
#endif
main(argc, argv)
int argc;
char *argv[];
{
#if defined(__GLIBC__)
printf("%s %s\n", __libc_version, __libc_release);
#else
printf("unkown\n");
#endif
return 0;
}
EOF
LIBC=""
${CC-cc} dummy.c -o dummy 2>/dev/null
if test "$?" = 0 ; then
./dummy | grep 1\.99 > /dev/null
if test "$?" = 0 ; then
LIBC="libc1"
fi
fi
rm -f dummy.c dummy
echo powerpc-unknown-linux-gnu${LIBC} ; exit 0 ;;
esac
if test "${UNAME_MACHINE}" = "alpha" ; then
sed 's/^ //' <<EOF >dummy.s
.globl main
.ent main
main:
.frame \$30,0,\$26,0
.prologue 0
.long 0x47e03d80 # implver $0
lda \$2,259
.long 0x47e20c21 # amask $2,$1
srl \$1,8,\$2
sll \$2,2,\$2
sll \$0,3,\$0
addl \$1,\$0,\$0
addl \$2,\$0,\$0
ret \$31,(\$26),1
.end main
EOF
LIBC=""
${CC-cc} dummy.s -o dummy 2>/dev/null
if test "$?" = 0 ; then
./dummy
case "$?" in
7)
UNAME_MACHINE="alpha"
;;
15)
UNAME_MACHINE="alphaev5"
;;
14)
UNAME_MACHINE="alphaev56"
;;
10)
UNAME_MACHINE="alphapca56"
;;
16)
UNAME_MACHINE="alphaev6"
;;
esac
objdump --private-headers dummy | \
grep ld.so.1 > /dev/null
if test "$?" = 0 ; then
LIBC="libc1"
fi
fi
rm -f dummy.s dummy
echo ${UNAME_MACHINE}-unknown-linux-gnu${LIBC} ; exit 0
elif test "${UNAME_MACHINE}" = "mips" ; then
cat >dummy.c <<EOF
main(argc, argv)
int argc;
char *argv[];
{
#ifdef __MIPSEB__
printf ("%s-unknown-linux-gnu\n", argv[1]);
#endif
#ifdef __MIPSEL__
printf ("%sel-unknown-linux-gnu\n", argv[1]);
#endif
return 0;
}
EOF
${CC-cc} dummy.c -o dummy 2>/dev/null && ./dummy "${UNAME_MACHINE}" && rm dummy.c dummy && exit 0
rm -f dummy.c dummy
else
# Either a pre-BFD a.out linker (linux-gnuoldld)
# or one that does not give us useful --help.
# GCC wants to distinguish between linux-gnuoldld and linux-gnuaout.
# If ld does not provide *any* "supported emulations:"
# that means it is gnuoldld.
echo "$ld_help_string" | grep >/dev/null 2>&1 "supported emulations:"
test $? != 0 && echo "${UNAME_MACHINE}-pc-linux-gnuoldld" && exit 0
case "${UNAME_MACHINE}" in
i?86)
VENDOR=pc;
;;
*)
VENDOR=unknown;
;;
esac
# Determine whether the default compiler is a.out or elf
cat >dummy.c <<EOF
#include <features.h>
main(argc, argv)
int argc;
char *argv[];
{
#ifdef __ELF__
# ifdef __GLIBC__
# if __GLIBC__ >= 2
printf ("%s-${VENDOR}-linux-gnu\n", argv[1]);
# else
printf ("%s-${VENDOR}-linux-gnulibc1\n", argv[1]);
# endif
# else
printf ("%s-${VENDOR}-linux-gnulibc1\n", argv[1]);
# endif
#else
printf ("%s-${VENDOR}-linux-gnuaout\n", argv[1]);
#endif
return 0;
}
EOF
${CC-cc} dummy.c -o dummy 2>/dev/null && ./dummy "${UNAME_MACHINE}" && rm dummy.c dummy && exit 0
rm -f dummy.c dummy
fi ;;
# ptx 4.0 does uname -s correctly, with DYNIX/ptx in there. earlier versions
# are messed up and put the nodename in both sysname and nodename.
i?86:DYNIX/ptx:4*:*)
echo i386-sequent-sysv4
exit 0 ;;
i?86:UNIX_SV:4.2MP:2.*)
# Unixware is an offshoot of SVR4, but it has its own version
# number series starting with 2...
# I am not positive that other SVR4 systems won't match this,
# I just have to hope. -- rms.
# Use sysv4.2uw... so that sysv4* matches it.
echo ${UNAME_MACHINE}-pc-sysv4.2uw${UNAME_VERSION}
exit 0 ;;
i?86:*:4.*:* | i?86:SYSTEM_V:4.*:*)
if grep Novell /usr/include/link.h >/dev/null 2>/dev/null; then
echo ${UNAME_MACHINE}-univel-sysv${UNAME_RELEASE}
else
echo ${UNAME_MACHINE}-pc-sysv${UNAME_RELEASE}
fi
exit 0 ;;
i?86:*:3.2:*)
if test -f /usr/options/cb.name; then
UNAME_REL=`sed -n 's/.*Version //p' </usr/options/cb.name`
echo ${UNAME_MACHINE}-pc-isc$UNAME_REL
elif /bin/uname -X 2>/dev/null >/dev/null ; then
UNAME_REL=`(/bin/uname -X|egrep Release|sed -e 's/.*= //')`
(/bin/uname -X|egrep i80486 >/dev/null) && UNAME_MACHINE=i486
(/bin/uname -X|egrep '^Machine.*Pentium' >/dev/null) \
&& UNAME_MACHINE=i586
echo ${UNAME_MACHINE}-pc-sco$UNAME_REL
else
echo ${UNAME_MACHINE}-pc-sysv32
fi
exit 0 ;;
pc:*:*:*)
# uname -m prints for DJGPP always 'pc', but it prints nothing about
# the processor, so we play safe by assuming i386.
echo i386-pc-msdosdjgpp
exit 0 ;;
Intel:Mach:3*:*)
echo i386-pc-mach3
exit 0 ;;
paragon:*:*:*)
echo i860-intel-osf1
exit 0 ;;
i860:*:4.*:*) # i860-SVR4
if grep Stardent /usr/include/sys/uadmin.h >/dev/null 2>&1 ; then
echo i860-stardent-sysv${UNAME_RELEASE} # Stardent Vistra i860-SVR4
else # Add other i860-SVR4 vendors below as they are discovered.
echo i860-unknown-sysv${UNAME_RELEASE} # Unknown i860-SVR4
fi
exit 0 ;;
mini*:CTIX:SYS*5:*)
# "miniframe"
echo m68010-convergent-sysv
exit 0 ;;
M68*:*:R3V[567]*:*)
test -r /sysV68 && echo 'm68k-motorola-sysv' && exit 0 ;;
3[34]??:*:4.0:3.0 | 3[34]??,*:*:4.0:3.0 | 4850:*:4.0:3.0)
OS_REL=''
test -r /etc/.relid \
&& OS_REL=.`sed -n 's/[^ ]* [^ ]* \([0-9][0-9]\).*/\1/p' < /etc/.relid`
/bin/uname -p 2>/dev/null | grep 86 >/dev/null \
&& echo i486-ncr-sysv4.3${OS_REL} && exit 0
/bin/uname -p 2>/dev/null | /bin/grep entium >/dev/null \
&& echo i586-ncr-sysv4.3${OS_REL} && exit 0 ;;
3[34]??:*:4.0:* | 3[34]??,*:*:4.0:*)
/bin/uname -p 2>/dev/null | grep 86 >/dev/null \
&& echo i486-ncr-sysv4 && exit 0 ;;
m68*:LynxOS:2.*:*)
echo m68k-unknown-lynxos${UNAME_RELEASE}
exit 0 ;;
mc68030:UNIX_System_V:4.*:*)
echo m68k-atari-sysv4
exit 0 ;;
i?86:LynxOS:2.*:*)
echo i386-unknown-lynxos${UNAME_RELEASE}
exit 0 ;;
TSUNAMI:LynxOS:2.*:*)
echo sparc-unknown-lynxos${UNAME_RELEASE}
exit 0 ;;
rs6000:LynxOS:2.*:* | PowerPC:LynxOS:2.*:*)
echo rs6000-unknown-lynxos${UNAME_RELEASE}
exit 0 ;;
SM[BE]S:UNIX_SV:*:*)
echo mips-dde-sysv${UNAME_RELEASE}
exit 0 ;;
RM*:SINIX-*:*:*)
echo mips-sni-sysv4
exit 0 ;;
*:SINIX-*:*:*)
if uname -p 2>/dev/null >/dev/null ; then
UNAME_MACHINE=`(uname -p) 2>/dev/null`
echo ${UNAME_MACHINE}-sni-sysv4
else
echo ns32k-sni-sysv
fi
exit 0 ;;
PENTIUM:CPunix:4.0*:*) # Unisys `ClearPath HMP IX 4000' SVR4/MP effort
# says <Richard.M.Bartel@ccMail.Census.GOV>
echo i586-unisys-sysv4
exit 0 ;;
*:UNIX_System_V:4*:FTX*)
# From Gerald Hewes <hewes@openmarket.com>.
# How about differentiating between stratus architectures? -djm
echo hppa1.1-stratus-sysv4
exit 0 ;;
*:*:*:FTX*)
# From seanf@swdc.stratus.com.
echo i860-stratus-sysv4
exit 0 ;;
mc68*:A/UX:*:*)
echo m68k-apple-aux${UNAME_RELEASE}
exit 0 ;;
news*:NEWS-OS:*:6*)
echo mips-sony-newsos6
exit 0 ;;
R3000:*System_V*:*:* | R4000:UNIX_SYSV:*:*)
if [ -d /usr/nec ]; then
echo mips-nec-sysv${UNAME_RELEASE}
else
echo mips-unknown-sysv${UNAME_RELEASE}
fi
exit 0 ;;
esac
#echo '(No uname command or uname output not recognized.)' 1>&2
#echo "${UNAME_MACHINE}:${UNAME_SYSTEM}:${UNAME_RELEASE}:${UNAME_VERSION}" 1>&2
cat >dummy.c <<EOF
#ifdef _SEQUENT_
# include <sys/types.h>
# include <sys/utsname.h>
#endif
main ()
{
#if defined (sony)
#if defined (MIPSEB)
/* BFD wants "bsd" instead of "newsos". Perhaps BFD should be changed,
I don't know.... */
printf ("mips-sony-bsd\n"); exit (0);
#else
#include <sys/param.h>
printf ("m68k-sony-newsos%s\n",
#ifdef NEWSOS4
"4"
#else
""
#endif
); exit (0);
#endif
#endif
#if defined (__arm) && defined (__acorn) && defined (__unix)
printf ("arm-acorn-riscix"); exit (0);
#endif
#if defined (hp300) && !defined (hpux)
printf ("m68k-hp-bsd\n"); exit (0);
#endif
#if defined (NeXT)
#if !defined (__ARCHITECTURE__)
#define __ARCHITECTURE__ "m68k"
#endif
int version;
version=`(hostinfo | sed -n 's/.*NeXT Mach \([0-9]*\).*/\1/p') 2>/dev/null`;
printf ("%s-next-nextstep%d\n", __ARCHITECTURE__, version);
exit (0);
#endif
#if defined (MULTIMAX) || defined (n16)
#if defined (UMAXV)
printf ("ns32k-encore-sysv\n"); exit (0);
#else
#if defined (CMU)
printf ("ns32k-encore-mach\n"); exit (0);
#else
printf ("ns32k-encore-bsd\n"); exit (0);
#endif
#endif
#endif
#if defined (__386BSD__)
printf ("i386-pc-bsd\n"); exit (0);
#endif
#if defined (sequent)
#if defined (i386)
printf ("i386-sequent-dynix\n"); exit (0);
#endif
#if defined (ns32000)
printf ("ns32k-sequent-dynix\n"); exit (0);
#endif
#endif
#if defined (_SEQUENT_)
struct utsname un;
uname(&un);
if (strncmp(un.version, "V2", 2) == 0) {
printf ("i386-sequent-ptx2\n"); exit (0);
}
if (strncmp(un.version, "V1", 2) == 0) { /* XXX is V1 correct? */
printf ("i386-sequent-ptx1\n"); exit (0);
}
printf ("i386-sequent-ptx\n"); exit (0);
#endif
#if defined (vax)
#if !defined (ultrix)
printf ("vax-dec-bsd\n"); exit (0);
#else
printf ("vax-dec-ultrix\n"); exit (0);
#endif
#endif
#if defined (alliant) && defined (i860)
printf ("i860-alliant-bsd\n"); exit (0);
#endif
exit (1);
}
EOF
${CC-cc} dummy.c -o dummy 2>/dev/null && ./dummy && rm dummy.c dummy && exit 0
rm -f dummy.c dummy
# Apollos put the system type in the environment.
test -d /usr/apollo && { echo ${ISP}-apollo-${SYSTYPE}; exit 0; }
# Convex versions that predate uname can use getsysinfo(1)
if [ -x /usr/convex/getsysinfo ]
then
case `getsysinfo -f cpu_type` in
c1*)
echo c1-convex-bsd
exit 0 ;;
c2*)
if getsysinfo -f scalar_acc
then echo c32-convex-bsd
else echo c2-convex-bsd
fi
exit 0 ;;
c34*)
echo c34-convex-bsd
exit 0 ;;
c38*)
echo c38-convex-bsd
exit 0 ;;
c4*)
echo c4-convex-bsd
exit 0 ;;
esac
fi
#echo '(Unable to guess system type)' 1>&2
exit 1
^ permalink raw reply [flat|nested] 10+ messages in thread
* Successful Build and Install
@ 1998-03-24 20:58 Pete Willemsen
0 siblings, 0 replies; 10+ messages in thread
From: Pete Willemsen @ 1998-03-24 20:58 UTC (permalink / raw)
To: egcs
Thought I'd pass on the info you requested: successful build and
install. Worked without a hitch.
Here's the output from config.guess
i686-pc-linux-gnu
I appreciate your efforts! Thanks.
Regards,
Pete
----------------------------------------------
Pete Willemsen Department of Comp. Sci.
willemsn@cs.uiowa.edu University of Iowa
---
http://www.cs.uiowa.edu/~willemsn
----------------------------------------------
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2014-05-09 9:30 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
1998-03-25 23:43 Successful Build and Install Per Bothner
1998-03-26 18:14 ` Joe Buck
1998-04-02 11:32 ` Jeffrey A Law
1998-04-02 11:32 ` Joe Buck
1998-04-04 14:20 ` Jeffrey A Law
-- strict thread matches above, loose matches on Subject: below --
2014-05-09 9:30 successful build and install Jiří Vymazal
2002-05-24 10:21 Benjamin Collar
2002-05-24 11:22 ` Janis Johnson
1998-08-17 23:32 Successful Build and Install S. Colin Leister
1998-03-24 20:58 Pete Willemsen
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).